Camry :: Unable To Find A Diagram For The Rear Brake Drum Of 2005?
Nov 7, 2014
Worthless Chilton's manual went in trash. I don't have a working PC and Im unable to find a diagram for the rear brake drum of my 2005 camry.
View 3 Replies
Nov 7, 2014
Advertisement
Camry :: 2005 - Rear Brake Drum Won't Come Off
I had a tire blow out, two nuts snapped off, custom rims came with car when I brought it, 12mm internal hex. I suspect they were over torqued.
I loosened self adjuster star all the way, and the drum still wont come off, I have tried heat with propane torch where hub meets drum.
And no parking brake isn't on. 2005 Camry right rear drum.
Camry :: Unable To Find 2005 Plug Wires?
My 2005 Camry LE four cylinder is past due for plug wires. I have tried Googling the correct part number for either NGK or Denso. The newest ones I can find are from 2001. What are the proper part numbers? My local parts store claims NGK and Denso does not make them for my car. I have a hard time believing they don't make plug wires for my car. If nothing else what is the correct Toyota part number?
View 3 RepliesAvalon 2005-12 :: 2007 - Find A Wiring Diagram For Speakers
Im looking to find a wiring diagram for the speakers. I have the 2007 Avalon XL. I dont have naviigation or JBL system. I want to install a line out converter to install an amp for my sub.
View 1 RepliesElantra XD (2001-06) :: Rear Drum Brake Replacement
This is my first time working on drum breaks, all the repair manuals and videos don't make it look too bad. I did have a question about the parts required to replace the rear breaks.
Assuming these breaks are very worn. What parts would need to be replaced in a typical break job.
The pics below are what I'm planning on buying:
Shoes
Rotors
Drum
Hardware Kit
Is there anything that I'm missing?
Accord :: Knocking And Vibration From Rear Passenger Drum Brake
I recently attempted to replace the rear brake shoes on my 01 Accord. Everything seemed to go reasonably well, but now when the brakes heat up I get a loud knocking and vibration while driving that goes away while braking. I popped the drum off last night and backed off the adjustment as the drum was hanging on one spot during rotation. This seemed to make it worse (though some minimal did stop suddenly in front of me, so I had to emergency brake and heat everything up). It has the original drums.
As a second, related question, there was no problem on my little test drive last night so I drove to work this morning. About 3/4 of the way there was when this started, and kept getting progressively worse. Understanding that you don't know exactly what the problem is, do you think it's reasonably ok to drive home (about 10 miles and I can stay off the highway)?
Knocking and vibration from rear passenger drum brake after replacing brake shoes, only while driving.
Car: 2001 Accord LX 4 cylinder
Took the drum off, backed down the tension on the adjustment screws. Drives and feels fine until the brakes heat up.
Ford - Escape :: 2011 - Odd Noises From Right Rear Drum Brake
Well, I have a 2011 Ford Escape. Recently, the car has been making two noises coming from the right rear drum brake.
I can only hear it going 5 mph or lower, possibly from road noise.
First noise: It sounds like someone is rubbing wet rubber on a wood floor (weird analogy). Not a grinding sound like a bad pad, but more of a hard rubbing sound.
Second noise: Whenever the car is at 5 MPH or lower and starts to decelerate, there is a high-pitched very small whistle coming from the same area. The pitch decreases as the speed does.
Got the brakes checked, no issues.
Accent LC (2000-05) :: Rear Brake Drum Cylinder Removal?
I must replace my driver's side rear brake drum cylinder but I am unable to fit any socket or wrench on the backing plate bolts holding on the brake cylinder. They are rusted and never been touched I think; how does one remove the bolts holding on the brake cylinder without stripping them? There is basically no room for leverage and the walls of a socket are too thick.
View 3 RepliesAccent MC (2006-11) :: Rear Drum To Disc Brake Conversion
I bought my accent in 2006 and it came with rear drum brakes and I want to know if it is possible to switch to rear disc brakes. I know that newer accents have all disc brakes so maybe it wont be that hard, but what do I need? I dont have abs. I asked the dealer like a year ago and they told me they wont do it. I have seen this conversion before in other cars that did not have rear disc brakes in newer versions either.
View 91 RepliesToyota - Tundra :: 2002 - Rear Drum Brake Adjustment
Don't seem to have an adjustment hole on my 2002 Tundra SR5, 2W drive. These are self adjusting brakes and, if they are, how to I go about adjusting them....simply backing up and engaging the brakes?
View 4 RepliesPontiac - Sunfire :: 2002 - Drum Removal For Rear Brake?
So I'm in the process of doing a rear brake job on a 2002 Pontiac Sunfire. Drum brakes. And (shocker - especially for a northern car that never had the job done before) the drum won't come off. I've spent two days with a propane blowtorch, PB Blaster, and a 3lb hammer. No dice. It won't even budge.
So now I'm thinking about taking an angle grinder to the drum and just replacing both (probably necessary, as I'm sure it's in terrible shape). I'm really at my last option here.
Camry :: Rear Drum Won't Go Back On - Brakes Are Too Far Out
I didn't put the rear drum on while adjusting the rear brakes, now the drum wont go back on because the brakes are too far out. How do I get my drum back on! This is on a 2002 Camry LE
View 6 RepliesPrius (2004-09) :: 2008 - Rear Drum Brake Shoe Thickness?
Getting ready to perform the clean and adjust rear brakes maintenance. I took a digital caliper and measured my rear drum brake thickness. The thinnest measurement I got was 3.19 mm.
I looked up the specifications and rear shoes brand-new are 4 mm. Minimum thickness allowed is 1mm.
I have 95K on my 2008. Since my brake shoes are showing close to brand-new measurements does this mean my rear drums are out of adjustment or is this normal?
XT1080 ?
Ford - Focus :: 2006 - Size Of Rear Drum Brake Bleeder Valve?
I replaced a brake cylinder on my 2006 Focus rear drum brake. Now, I need to bleed the brake fluid, but I can't find a wrench to fit the nut.10mm is too small and 11mm is too big. What's going on? Could it be the rusted nut has grown in size enough to make the 10mm wrench too small? Or, is the nut standard?I know the drum bleeder nut I know the front disc brake bleeder brake is 10mm. So, I am thinking the rear should be metric, but since it's drum, I am not so sure. What the size is?
View 13 RepliesFord Brakes/Suspension :: 1997 F250 - Passenger Side Rear Drum Brake Was Full Of Oil
Recently purchased my first Ford truck, a 97 F250 w/7.3L diesel. I discovered the passenger rear drum brake was full of oil. Cleaned it up and put it back together to do some research.
I see how the hub comes off and there are two bearings in it an an oil seal. The bearings are lubed in wheel bearing grease. Does differential oil circulate through the bearings too?
It doesn't look like a difficult job. Do the seals go bad often or could this be due to a clogged differential vent? Truck has only 100k miles. Any gotchas I should be aware of?
Celica :: 1992 GT 5 Speed - Can't Find A Fuse Box Diagram
So I bought a Celica a while back and the fuse box is uncovered meaning the cover that tells you which fuse is for what is gone. I can't find the cover saying which fuse is what online anywhere. If someone has a '92 Celica and can take a picture of it, that would save the day for me. It's a 1992 Celica GT 5 speed, 2.2L. Note that there are two fuses missing in the picture. I'm working on it right now, that's why.
View 2 RepliesElantra HD (2006-10) :: Unable To Remove Rear Brake Rotor?
2008 hyundai elantra. I'm trying to replace the rear brake pads and rotors. I was able to do the front ones easily. Any good tips to remove this rotor. I have tired tapping on a rotor and it wont budge.
View 2 RepliesCamry :: 2009 Toyota Unable To Start - Light On Rear Windshield Defroster Blinking
First time I'm having an issue with my Toyota Camry 2009 model.
See video: [URL] .....
I'm wondering if this is a starter issue because the battery seems to be fine (can turn on radio, lights are working). The strange thing i noticed was that the light on the rear windshield defroster was blinking. I haven't turned that on in months.
Also, is this covered under warranty ? I bought the extended warranty when i purchased the vehicle in 2008. If i'm not mistaken I'm still covered under it. Is there a place (online) where i could check my extended warranty period ?
Ford F-150 - 1997-2003 :: Reconnect The Brake Drum End Of The E-Brake?
How the heck do you reconnect the brake drum end of the E-Brake ?
There seems to be not enough play in the cable to be able to hook it.
Accent LC (2000-05) :: Drum Brake Adjuster Not Functioning
The star wheel is not bound up. I can adjust in manually and it clicks properly when tightening. The adjuster arm is touching the right area of the star wheel. What happens is, I manually adjust the rear brakes until they are close to perfect. I back up hoping to get them to self-adjust to the proper spec, and instead of tightening, they seem to loosen a few clicks and stay that way, leaving me with "half way" rear brakes. Meaning, it would take me a few hundred feat to come to any meaningful stop when pulling the E-brake.
I can also feel the difference between the rear brakes functioning, and not, despite their secondary role, and these are not functioning properly. Right after a drive, I can jack the car up and the wheel spins freely again as if I never adjusted them in the first place. They don't unadjust themselves to the point of being completely ineffective, just to the point of not being nearly how they should. I'd expect to be able to lock them up by pulling the e-brake, and it isn't even close.
When I apply the e-brake, I can hear them "grinding", sort of touching but not really. Everything seems to be installed correctly.
Pontiac - Bonneville :: Removing Hub From Front Brake Drum
i have a 1966 pontiac catalina and i am replacing most of the brake components including the drums, which a car of this vintage has at the front also. the new drums don't include hubs, so i will have to swap the old hubs to the new drums. do i have to go to the machine shop to have them press these apart?
View 16 Replies