Camry :: Changing Out Left Front Cv Joint Axle
Apr 1, 2012
Looking for info on changing out my left front cv joint axle.My boot is busted on the outter axle but iam going to change out the hold axle then my inner and outter are done the same time.Is there any body that attempted this on there own or a good thread that explains the steps to take on this job.My ride is a 2004 camry auto with the four bagger.
View 3 Replies
Advertisement
I just bought a 2003 Hyundai Elantra GLS, yesterday. 167k. Some faded paint on top areas, dead battery & in need of driver's front CV joint axle i believe, clicks when going around corners. Starts without hesitation, no smoke, no ticking, very clean and has only had 1 owner.
View 10 Replies
I noticed on my 03 excursion on both sides of the front axle there is a circle plastic o ring behind the u joint that is lose? Nothing is leaking and no signs of leak marks ever. Kind of looks lik a spacer ring of some sort because its at least 1/8th inch thick plastic. Also some time ago I posted about a whistling noise but never got a answer but its only there when im in 4wd there is a whistling noise from my right side and my locking hub when I turn it the hub seems lose and has a crunchy feeling to it. I just bought it a few weeks ago and now I am running into a whistling noise and noticed theres a piece of plastic that looks like a spacer....
View 14 Replies
I have a '01 F250 with a frozen u-joint in the driver side front axle. My question is can I put it together without the axle and drive it?
View 2 Replies
So now that it is becoming colder out (40's in the morning 50's in afternoon) I have been experiencing signs that an inner joint on one of my axles is going bad. When driving while the vehicle is still cold, and even when it is just warmed up, I have bad vibrations while accelerating. I've ruled out other things and even had the car in the air and had it checked out at a stealership but of course they couldn't reproduce any of the vibrations. It was warm out the day of the appointment.
View 6 Replies
I have a 2012 Ford Focus which infrequently makes an odd grinding, scratching sound by the front LEFT tire/ axle. It only does it when turning to the RIGHT. It usually does it as I'm coming out of the turn, not into the turn; so when the tire is moving back into the straight position. It's just the sound, you can very slightly feel it when it happens but really no stability or other steering issues. What is causing this sound?
View 3 Replies
I have an 06 gs300 awd. My left front axle boot is torn wide open. I've called multiple parts stores, looked online. And I can't seem to find one anywhere but the dealer. I have found one for gs350. So my question is will that one work in my gs300? What is the part number from the dealer is different between 06 and 07?
View 5 Replies
1998 Honda Civic EX, automatic transmission, 145K miles. Purchased three weeks ago.
Newly purchased used car has a knock emanating from the left front axle area. It's a rotational thumping/knocking sound that occurs about every 360 degrees of the tire rotation and only in forward and backward full-lock left turns. The car also has a small vibration/wobble in the left front. It's been narrowed down to the CV half axle outer bearing. What is puzzling is left front knocking from the outer CV joint is usually associated with full-lock right turns (and vice-versa) However, the left front knocking/thumping only happens as stated above (full-lock left turns).
Recent front end parts replaced:
1) Left front hub assembly and bearing
2) Inner and outer tie rods on both left and right sides
3) Front left caliper
4) New front brake pads on both left and right sides
5) Automatic transmission 3 x 3 drain and fill + Lubegard red
View 18 Replies
OK I need to replace just the boot, joint is fine. I have everything disassembled but cannot get the cv joint off the end of the axle. What am I missing here? All other CV Joints just come off with a few whacks of a hammer. Is there something special on these I'm missing?
View 14 Replies
Can I re-use this shaft or is that ring around it no good. The ring is around where the bearing sits. It is a circumferential hump all the way around.
View 14 Replies
I unstuck my front axles yesterday and while under the car spinning the front axles freely and enjoying my easy fix, I noticed a rubber seal (a thick squared edge round rubber seal) sitting loose and spinning freely. Its next to the axle joint, right before it disappears into the housing.
I'm guessing this is a dust seal of some kind. There is no fluid leaking out...
I'm wondering if I can just press fit this thing back into place or do I have to take the whole front wheel assembly (hub, bearing, axle, etc) to get the seal back into place.
I'm wondering if it broke off from a larger seal or if this is the whole thing? You can see how the seal isn't sitting quite straight. It actually just spins around.
View 9 Replies
Just to clarify, I've got a UK spec B5 wagon, manual, 1.8T (AEB, I believe) and it's a 2000. Last night when I was driving home, either my CV joint or axle on the driver (right) side blew out. Needless to say, I'm going to replace my axles or just the outer joints, but I've been shopping around and I'll find parts that will fit an A4 with a 5 speed and AEB but not a Passat, or parts that fit strictly AUG or ATW engine codes. How would I go about finding which axle will actually fit my car?
Here's a video so you can hear the noise : [URL] .....
View 1 Replies
Did ball joints this weekend and now have little axle fluid leaking out passenger side. was going to change axle fluid when i saw this so continued and when pulled the fill plug i would say 8oz or more came draining out. Did I mess up the seal inside the tube?
View 5 Replies
On a level-of-difficulty-scale from 1 to 10. 10 being the most difficult. How difficult is it to change the upper control arm and the lower ball joint?
View 3 Replies
Picture if you will...Removed tire, caliper and rotor. Removed hub, and knuckle containing the stub shaft/spindle with it's yoke for the U joint. You are now looking at the end of the axle tube, with the axle shaft in it, one end connected to the differential carrier, the other end has the yoke for the U joint on it. Just inboard of the yoke, is a seal. Apparently it's called a "dust seal" is there a bearing behind this, or is the first bearing all the way in at the differential? When I was doing my brakes, I noticed the passenger side u-joint is shot, and the axle wiggles around in the dust seal. Figured I'd replace the seal while I was doing the U joint. Also, how do I get the axle shaft out? Just pull, or do I have to remove a C clip from the inboard end? What is the right National part number for the seal? I have a 6/2000 Excursion.
View 2 Replies
I have the dreaded click-click-click noise when turning that is indicative of my CV joint going tits up. Checking it out the boot is split and there is some grease. So, I plan on going ahead and changing both sides drive axles out, since the Camry has 178k on it (yeah, 178k on a 2009.)
View 14 Replies
I had my passenger side cv axle replaced two months ago 2002 camry xle 110k miles for the ABS broken ring. After that start to here a shuddering intermittent noise from the front of the car more clear on turning the steering wheel, sometimes I here a metal on metal noise on bumps, axle was a brand new one and a press garage pressed the bracket on it..
View 6 Replies
Scion TC for Camry SE 2007.
I changed the front brake pads and resurfaced the rotors. After putting everything back together, I took the car to test drive it. The stopping power is fine and there is no squeaking or robbing sounds. However, when I apply the brakes at lower speeds moving forward there is knocking sounds the comes with the tire rotations. What is the reason for this sound?
This is my second time changing the pads and rotors, with the first with no issues. I put grease between the shams and the pads, and I sprayed the rotors with brake cleaner before the installation.
View 8 Replies
I have a 2000 Accent that I changed the clutch and CV Axles on and now the transmission seams to be stuck. When i got done replacing the axles and installing the brakes I spun the wheels while installing the nut to aline the cotter pin. Once I got the car down, serviced the gear oil, bled the clutch master. Went to drive the car and it wouldn't move .
View 5 Replies
My wife's 2007 Mazda3 is making a very slight clicking sound every while coming out of left turns. It's somewhat intermittent, only happening every few turns. I did a quick visual inspection and noticed that there was grease around the CV boot. The problem started about five days ago (or at least the noise started appearing five days ago). Three weeks ago I had the struts replaced, so I'm wondering if they could have torn the boot while replacing the struts, or if they didn't notice the issue.
Is the CV joint shot, considering this is only an intermittent sound, or is there something else that could be happening? Also, what is a typical repair cost for a CV joint (or half axle replacement) on a 2007 Mazda3?
View 3 Replies
So while my wife was driving down the highway, something rattled under my Camry, possibly front around the left wheel, under the engine or the like, then it came off. She said it looked like a circle, cut in half (or like a horseshoe of something). She didn't notice any strange behavior or drivability issue. She got home fine. She just said, it could have looked like a brake shoe also. Because it's wet here, I can't get under the car to check, so before I get a chance to do that.
View 7 Replies