Camry :: Rubber Washers Stuck To The Valve Cover
Jun 4, 2015
2007 2.4L Camry LE.
Took the plastic engine cover off and found that there are two rubber gasket/washers that stayed stuck to the valve cover (around the threaded rods that stick out of the cover). When I tried to remove them, they disintegrated. Now, my plastic engine cover is having problems tightening on properly, if that makes sense.
So, if you look at the engine cover, you take the two nuts off and remove the cover. There are rubber isolators/gasket that is there. Mine have disintegrated. Call to the Dealership says I have to replace the entire cover as you cannot get those separately.
View 1 Replies
Advertisement
The bolt that holds the dipstick on the valve cover. i have tried for ever to get this thing off. soaked it , got a skinny wrench on the nut underneath but think it might be stripped (1/2 inch grinded out a little). going to try and get a set of skinny wrenches tomorrow , mine bent. tried vise grips on top of the bolt and put a box wrench on the nut , and gave it my all. The damn thing won't budge.
Also, any tips on the rest of the valve cover bolts. I had to remove some from inside the fender well but barely got to them. My question is not getting these out but getting them back in. And how the heck to you torque these things??? The bolt i mentioned above is creating problem, and I only have so much time
View 8 Replies
I was loosening the bolt that holds down the number one spark plug wire when it just spun off leaving less than half the bolt in the valve cover. I tried using the grabbit extractor but that did not work.
View 8 Replies
so I have a 2azfe engine
So there's an oil leak coming from the valve cover gasket (just purchased vehicle dirt cheap with 220k)
found this
Notice all the oil sitting on top of the exhaust mani gasket
In the left(lower) part of the picture it appears to be scraped.
the gasket appears to be newer, I did NOT use a screw driver to remove the valve cover, which is what this appears to have been done..
Can this be sanded down then filled with jb weld, and then regasketed?
View 7 Replies
So I'll be taking on a project to replace the valve cover gasket on my 2002 Camry V6. There's a bit of leakage through the gasket. And while I'm at it, I'll replace the spark plugs as well. I'm looking for a write up on this project. did a lot of searching but couldn't find anything.
View 14 Replies
I changed my leaky valve cover gasket today, along with my spark plugs and PCV valve. Now after driving a few minutes my CEL and oil light come on.
the car was/is low on oil from the leak. I was going to change the oil but it has been pouring rain today and it was all I could do to get the valve cover gasket done.
I put two quarts in after the oil light came on, I haven't had a chance to check the level since then.
I don't see oil leaking anywhere on the engine. I cleaned it up pretty well around the valve cover and should see any new oil easily.
How low does it have to be for the oil light to come on?
View 1 Replies
I have a 2003 Toyota Camry with 210,000km on it. Today I popped the hood, noticed the coolant was slightly low in the over flow reservoir so I looked around the engine bay. Now I know generally coolant does not go up that far and it's just oil... But this has got my head turning. There's a crusty coolant residue drip that looks to start at the valve cover. At first I thought maybe the water pump was leaking, and the pulley was spinning it farther up, or spraying back from a rad leak when driving. but the fact it's crusty and A clear line that looks like a drip that's a slow leak and has crusted over time makes me wonder.
I mean generally coolant wouldn't come out of the valve cover unless it was right full of coolant, causing enough pressure to push it out... Am I wrong ? Once I get to the shop on Monday I'm going to pressurize the cooling system and pull the spark plugs and the valve cover to look at the head, The highest spot I see the drip start is the valve cover, only thing I could think of is the intake leaking, and traveling over there but even then, it doesn't make sense to me. The thermostat housing is about 2.5" under so it can't be that... It's such a small leak, the reservoir is only down about maybe half an inch and the oil looks clean as can be.... There's some pictures below that you can somewhat see it.
View 12 Replies
I have a 2002 toyota camry xle 6 cyl i believe i have a valve cover gasket leaking vehicle has 112,000 miles. is there a step by step removal proccess i can access. I have done one on a 1995 honda passport 6 cyl how difficult is it
View 2 Replies
Own a 2000 Camry XLE 6-cyl. Both valve cover gaskets are leaking. Rear one leaks onto the manifold and causes stench. Have been quoted $350. to replace because the job is complicated. Have any of you done this on your own, and if so, would you recommend it or go to a qualified mechanic?
View 9 Replies
2002 Camry 4 cyl was leaking a small bit of oil on the rear passenger side of the valve cover - about directly behind where the timing chain is. I replaced the valve cover today, but noticed that there is still a small amount of oil leaking at the same spot. Is this a common problem with the '02 Camry? Or perhaps I have a valve cover problem?
View 2 Replies
About, one month ago my car shut off while driving(pretty scary at the time). I pulled of the road and attempted to start it again. Everything looked good there, but as I was making my way home from work it started to act funny. It would not acknowledge me depressing the accelerator. When I got home, I ate supper, then went to have a look.
The car would turn on, but not acknowledge me pressing the accelerator at all, It did however go up to 30 mph at a snails pace as if it was coasting down a hill. I plugged in my code reader, and it read that the Throttle Body Valve was stuck open. I took it off and tore into to it a bit. I noticed the gears inside the TB itself were corroded and the butterfly valve was locked up.
I replaced the part, and tried to turn my car on with the new TB. All the dash lights are in working order, however upon turning the ignition to crank the engine, the whole car system shuts down. No lights no nothing, besides the car door open sound. The car will remain like this regardless of the key position until I have reset the batter(take off the terminals and put them back on) to which the process repeats itself.
The code reader says no codes are stored because I obviously reset the battery. So now am at a standstill.I believe the old TB froze up, because I had to run in through 3 ft standing water during a storm, and then deployed shortly after(I'm in the service) for a few months while letting the car sit.
View 1 Replies
My GTI has a problem i don't know how to fix. Shift knob on the automatic mk4 (2005) GTI, has a rubber piece that covers the ther gears when you are in the one of your choices. Such as if you were to be in drive then park reverse and neutral would be covered by the rubber sheet, as would the gears under drives such as the 4th 3rd and 2nd gears. That sheet of rubber on the car has been unattached from the front side of the sifter so that there is a hole in front of the shifter if I were in drive, the rubber piece that covers that hole was jammed into the front part of the gearbox (directly under the shift knob when in park).
I managed to get the rubber piece out from under there with a pair of very fine pliers. now my problem is how to attach the sheet back to the front of the shift knob. the rubber sheet seems to be very loose and when it is moved side to side you can see that there is some sort of zipper pattern along each edge of the rubber cover. MY QUESTION IS!! how to reattach the rubber cover?? or do i have to take that section apart and replace it?
View 1 Replies
This may be my only chance to do a step-by-step ...
Tools Required : Fingers (preferably attached to hands)
Step One : Check diver side floorboard for cleanliness (people are going to see it in the pics)
Don't worry about passenger side. There will be no pics of it.
Step Two (fingers required for steps two through seven and ten) : Vacuum driver floorboard since there will be pictures made of it.
Step Three : Remove old, worn out brake pedal cover.
Step Four : Remove aftermarket brake pedal cover from ridiculously oversized Amazon box that's still in the passenger side floorboard.
Step Five : Take a picture of the old and new covers together to make fun of the old one.
Step Six : Install new brake pedal cover.
Step Seven : Remove new brake pedal cover and re-install right side up..
View 14 Replies
I had it checked out at the dealer and they called it a "weep" so they went on to tell me that VW probably wont approve warranty work for it. I pushed for them to take pictures and send it in anyway.
Now assuming they won't do it, I have been looking for a DIY or a technical order on the job but I can't find anything.
View 7 Replies
My car is in the shop and has a leak at the Power Steering Pump. The rubber O-ring on the Power Steering Pump Solenoid Valve (p/n 4417030120) is leaking fluid. The Solenoid Valve is ok, just the Rubber O-ring is bad, but it looks like you have to buy a complete new Solenoid Valve to get the O-ring (a lotta bucks).
I did find a Lexus Power Steering Pump rebuild kit online at, but I can't see if it includes the solenoid valve o-ring or not. Have to replace their solenoid valve o-ring?
View 10 Replies
Just found valve cover of my Tiguan is leaking out oil this morning. Will go to dealer tmr for gasket replacement. My car is just over 50k miles. What happened to VW's car quality control???
View 5 Replies
I want to have my oil cap sit close to the valve cover rather then have that long funnel.
I want to go from this:
To this:
View 7 Replies
Haven't had the engine cover off for about 25k now (cleaned it up under there last time I changed plugs.) Took it off today and noticed it's a little oily on all four sides around the valve cover.
Pretty sure I can account for the oil that's near the filler cap... I don't recall spilling enough that would completely go around the entire valve cover though...
But how did it end up so high on top of the valve cover on the corners? It's even a little wet looking on the back if you look hard enough..
I only have 4600 miles left of the 10/100 warranty so I'm glad I caught this and hope the dealer can do something about it... or are they going to tell me this a "normal" amount of seepage? I haven't owned a vehicle with plastic valve covers before so I don't quite know what to expect.
View 7 Replies
So with about 70,000 km on my 3.3 V6 I'm noticing some oil seepage from the valve cover gasket. It's not enough to budge the oil level on the dipstick, and frankly not the sort of thing I would bother having fixed (especially with a leased vehicle). The only thing bugging me is that the alternator is getting pretty grimy and dirty from it, and I'm wondering how much it can take.
View 12 Replies
when replacing valve cover gasket, using the cork based one. Do you use any gasket sealant or any kind of silicone or just put it in by its self.
View 5 Replies
I took it to the stealership to get the alternator and some vac. lines replaced all under an extended warranty. They informed me that both valve cover gaskets and right side cam adjuster gaskets are leaking. By no means am I a mechanic or close to but I am trying to get this stuff done as cheap as possible so I am going to try to tackle this myself.
View 3 Replies
