I am planning to replace the headlight (high beam) light of my 2006 Toyota Camry. The original OEM light lasted for nearly 6/7 years.
I noticed in some forum that "Sylvania 9005SU SilverStar Ultra High Performance Headlight Bulbs" is good, but it has short life of less than 1 year.
I drive a 96 Subaru Legacy. What does it mean when one of the high beams is dimmer (less light output) than the low beam? I am using a brand-new bulb. It's not an adjustment issue because I was looking at the bulb when it was outside of the housing and it clearly gets dimmer when you switch to brights. However, they are equally bright when on low-beam, so I don't think its just a crossed wire.
View 2 RepliesHow to replace low beam bulbs? all info i found was talk about whether they were covered under warranty or not? I got extended maintenance warranty to 100k miles, but bulbs, I don't think so. I just noticed today that both were out on low beam, high beam are fine. Should I take car to dealer? or is this something I can do myself?
View 3 RepliesLooking for detailed instructions on replacing the low beam passenger side headlight on a 2004 Phaeton...
View 1 RepliesI need to replace the low beam headlight on the drivers side. Any quick way to do this, and how much and what type is the bulb?
View 3 RepliesThe headlight on the driver's side has burned out, should i move the battery in order to get to the bulb?
View 3 RepliesAfter months of researching and foruming, I made a satisfied decision to upgrade from Halogen to aftermarket HID Bi-Xenon which is really great in color and high visibility at night.
Moreover, behind Halogen headlight there is a 8mn bolt where you will use your hand or 8mn wrench (remove the black plastic cover over bumper to make more room). Twist it Clockwise to lower and Counter Clockwise to raise headlight.
I aimed mine relatively low because my intention is for a great looking light, high visibility and not blind on-coming traffic and yeah I'm so satisfied.
So I had an issue with my hid lights, I replaced one ballast and 2 new bulbs and they work fine now but the passenger side is stuck on high beam. When i turn on the brights only the driver side gets brighter, how to fix this? I only replaced the driver side ballast
View 3 RepliesWhy I have one headlight gone dim, high beam will not work. This just happened about a week ago and I changed the bulb and it's still the same.
View 9 RepliesI'm hooking up some Ridgid driving lights and want to tap into the high beam headlight power wire to activate the relay. Which wire is for the High beams on a 2006 F250 Diesel??
View 8 RepliesAny tips for replacing the passenger side high beam? I can get my hand in there by there is no way to turn the bulb. Any easy tool to grip and turn the bulb?
View 5 RepliesI suspect that I already know the answer but will ask anyway. In another lifetime I could adjust the headlights on my car (two spring-loaded screws on each bulb for up-down and side-side adjustment).
The low beam on my 2010 Camry seems to run out at about 30 yards. Some night I am going out and actually measure it. High beam has no problem as it goes forever. It just seems that the low beam does not allow me to see very far down the road. I have not asked the dealer yet and thought I would ask here first. Is there a way to adjust the headlights on these new cars with the total headlight system in one big package?
I have a 2004 Camry. A few months ago, the LH headlight stopped working. Thought it was the bulb, but wasn't. High beams work, DRLs work, socket good, contacts good. But, when I tap on the headlight cover, the low beam comes on, and stays on. What's going on here?
View 4 RepliesMy 2006 Prius (Model NHW20) has a strange headlight problem. On the passenger side, the high beam light is out but the regular headlight works.
On the driver side, the high beam is working but the regular headlight is out.
I don't think it's the fuses but I'm not sure. No amount of interchanging the following fuses changes anything about the issue:
1. 10A H-LP HI RH
2. 10A H-LP HI LH
3. 15A H-LP LO RH
4. 15A H-LP LO LH
I have a 2007 Camry SE V6 and noticed that my high beam/DRL won't turn off even when the car is off. I had to take out the fuses for both so it wouldn't drain my batteries. Its the exact same issue as the OP in this thread:
High Beam Headlights Stuck On. Is it a relay issue or switch?
I have a 2011 Camry XLE. My left high beam is not working not even for DRLs... I have replaced the bulbs and this is not the case.
View 3 RepliesWhere's the fuse for the DRL ...both my DRL and high beam isn't working ...I checked the bulb and is seem fine. I did check the fuse box on both locations ( under the hood and steering wheel) none of them says DRL fuse in there ...
View 14 RepliesI'm trying to replace my dads 2007 Camry XLE japan built headlight assembly because his are insanely oxidized. Besides OEM's and CAPA's, what else are there? Any good aftermarket headlight assembly and achieve great results?
View 8 RepliesI have an '06 Camry, which has lost all power functionality. The follow items just stopped working
1. Key fob -- keyless entry and alarm stopped working
2. high beam doesn't come on when headlight is on. However, when headlight is off, it comes on--go figure
3. Power door lock also does not work, even from driver side door. Have to lock all doors manually
4. Interior lights don't come on when door is open.
My car is fully stock, with all options available to me (cold weather package not available here). The low-beam triple-LED headlights are aimed way too low compared to all my previous cars, and where they should be. BUT high-beam is aimed properly. So if I adjust the low-beams up, my high-beams might end up lighting up the trees, not the road.
If adjust the headlights up on a fully stock car (not lowered at the front)? Are the high beams still lighting up the road fine? And if you can be specific as the number of turns on the screwdriver, it'd be good too to have an initial adjustment reference.
This morning a dash light informed me a headlight bulb was out. It was my DTR light on the passenger side.
I purchased Sylvania H7 high intensity, installed it and it failed to work properly. Daytime light on only drivers side works.
High Beam on , both lights works.
I checked my manual and it said to check fuse in the 5 slot on the driver side dash/door panel and there actually is no fuse in there. I checked the driver side and there was no fuse there either.
I replaced my driver side bulb last year and it took 5 mins....i am already 4 hours into this!