I didn't put the rear drum on while adjusting the rear brakes, now the drum wont go back on because the brakes are too far out. How do I get my drum back on! This is on a 2002 Camry LE
View 6 RepliesAfter putting my Ford Ranger in park and pressing down on the E-break to get the news-paper or mail. I've noticed that there is a consistent squeaking coming from the back drum brakes when the brake pedal is applied. But only for a certain period of time; then the squeaking stops.
View 8 RepliesI have a 1997 F150, 4X4. My mechanic says its time for new brakes and was curious if it would be worth possibly converting from drum brakes to disc brakes??
My mechanic has quoted me $300 to do the rear brakes, would it be worth the extra money to convert??? I really don't care for drum brakes. I have done a search on the internet and every time it brings up the issue with the parking brake.
I have a 2000 CR-V with rear drum brakes that make quite a bit of noise. When I press the brake pedal, they make a noise like the shoes are grinding on something other than the drum itself. Also, when I press the pedal at the right amount of pressure at the right speed, I get a loud high pitched squeal as if there's a metal tab rubbing on the drum. I did this brake job with my dad about 6,000 miles ago (154xxx miles now) including the front pads. We did everything right and bled the brakes VERY thoroughly.
We used the same drums as before (however, we replaced the front disc rotors) and everything is how it should be. I even adjusted the shoes' pressure on the drum a bit to see if it would stop. Also, the squeal noise seems to be worse when I haven't driven the car for about 2 hours or in the morning when it's colder and the brakes haven't been used in several hours. What's causing these noises?
Received the truck, 1989 Ranger XLT long bed single cab from my mom. It had been used by my younger brothers for some years, and then sat at mom's for a couple years.
It needed new front brakes badly, so replaced rotors, and pads. No unexpected problems there.
Looked at replacing the rear. Both adjuster cables were initially broken, so they obviously weren't adjusting, or braking. Replaced with a hardware kit, and shoes, and drums. Its the 9" drums, BTW.
Still not actually braking. I can tell this, when at a stop sign in the winter, with the brake pedal held down, and the backs will still spin, with the tranny in D. Even on gravel or grass, this'll happen.
One shop told me this is because the axle seals are leaking. THey've never leaked badly, and the axle fluid isn't low, by and shade of the imagination. Also, this theory falls apart, when the parking brake works just fine, right? Its just hydraulically that they don't work.
I've since replaced the wheel cylinders, the brake line from the frame to the rear axle, and the master cylinder. No change. Bleeding them doesn't seem to be a problem; i.e. no lack of or little fluid witnessed, it seem fine.
Also have bypassed the RABS valve for about a year or so, and its made no difference. Last fall I pulled the drums off, and manually adjusted them, and it didn't seem much better either.
I'm having a problem with my rear drum brakes locking up when I press the brake pedal. I've had this problem before, but ignored it because it wasn't too bad. It would just release after taking my foot off the brake pedal.
1998 F-150 XLT supercab 4x4 front discs, rear drums 4.6L v8 175k miles
I cleaned my master cylinder and bled all brake lines so they have fresh fluid. Now that my brakes work way better, my rears just lock up. I put new brake cylinders on, still locking up. I went to a junkyard today and replaced the proportional check valve, brakes still locking up.
Could I maybe have did something wrong when cleaning the master cylinder? I'm sure I put it back together correctly. Anything else i should look at? bad lines maybe?
Changing rear drum brakes to discs? I've done it with my 94 explorer, and i was wondering if the axles are the same, just swap the hardware like the explorers are.
View 14 RepliesI got a 2002 f150, right now it has a 9.75 with disc brakes. But it exploded. I can only find a 9.75 with drums in the wrecking yard. Can I just swap my disc brakes on to the axle with drums?
View 1 RepliesRecently purchased my first Ford truck, a 97 F250 w/7.3L diesel. I discovered the passenger rear drum brake was full of oil. Cleaned it up and put it back together to do some research.
I see how the hub comes off and there are two bearings in it an an oil seal. The bearings are lubed in wheel bearing grease. Does differential oil circulate through the bearings too?
It doesn't look like a difficult job. Do the seals go bad often or could this be due to a clogged differential vent? Truck has only 100k miles. Any gotchas I should be aware of?
I had a tire blow out, two nuts snapped off, custom rims came with car when I brought it, 12mm internal hex. I suspect they were over torqued.
I loosened self adjuster star all the way, and the drum still wont come off, I have tried heat with propane torch where hub meets drum.
And no parking brake isn't on. 2005 Camry right rear drum.
Worthless Chilton's manual went in trash. I don't have a working PC and Im unable to find a diagram for the rear brake drum of my 2005 camry.
View 3 RepliesI've begun restoring my grandpas 1970 Chevy c/10 but I can't seem to get the brake drums to budge. I tried several cans of lubricant and even beat on one with a sledge hammer till the outside broke off. But the front face of the drum still won't come off. How to remove them?
View 14 RepliesI bought a 2012 Corolla S and I feel that the rear brakes are a little cheap. Has swapping brakes but how?
View 3 RepliesMy 1963 Holden has drum brakes all round. The fronts had always been a problem pulling and shuddering. I have had the drums machined and fitted new shoes and adjusted them up correctly. The shoes are the correct fit in the machined drums.
They are now working really well when cold. Once they heat up I am getting a bit of shudder, nowhere as bad as before but still annoying. No longer pulling to any great extent. My question is, why would the shudder only happen after driving for a while and the brakes warm up?
When I back up the T-egg and at the same time I press the brake to control the speed. I hear a strange sound coming from the rear brake. Something like I hit something. How often? I would say, always. I went to the dealer 2 months ago and could not duplicate at that time.
View 8 RepliesI have recently replaced my stock pads with pbr ceramics,front and rear. now my rear brakes are squeeling loud everytime i back up. i have tried to file the edges, did not work. What to do? change pads?
View 6 RepliesI have a 2005 Toyota Camry that we purchased 14 months ago. When purchased it had bad brakes so the dealer replaced the rotors and calipers at their expense. A month ago I took the car in for a routine oil change and was notified that my rear calipers were stuck open and that my rear brakes were not working and rusted. The rotors look hardly worn, the one on the passenger side has some deep grooves in it and the driver side is pitted. We feel that we had poor work done when the brakes were replaced and that the back never worked. After the brake job was done we would get some "chinging" noise in the back brakes and I had them inspected twice and they said everything was fine. But now we find out they weren't fine.
View 8 RepliesI just replaced the rear brake shoes and they seem really tight to the drum on the left side. Right side was liitle tight but OK. Self adjuster is screwed all the way in so I'm not sure why this happened.
View 16 RepliesThis is my first time working on drum breaks, all the repair manuals and videos don't make it look too bad. I did have a question about the parts required to replace the rear breaks.
Assuming these breaks are very worn. What parts would need to be replaced in a typical break job.
The pics below are what I'm planning on buying:
Shoes
Rotors
Drum
Hardware Kit
Is there anything that I'm missing?
I recently attempted to replace the rear brake shoes on my 01 Accord. Everything seemed to go reasonably well, but now when the brakes heat up I get a loud knocking and vibration while driving that goes away while braking. I popped the drum off last night and backed off the adjustment as the drum was hanging on one spot during rotation. This seemed to make it worse (though some minimal did stop suddenly in front of me, so I had to emergency brake and heat everything up). It has the original drums.
As a second, related question, there was no problem on my little test drive last night so I drove to work this morning. About 3/4 of the way there was when this started, and kept getting progressively worse. Understanding that you don't know exactly what the problem is, do you think it's reasonably ok to drive home (about 10 miles and I can stay off the highway)?
Knocking and vibration from rear passenger drum brake after replacing brake shoes, only while driving.
Car: 2001 Accord LX 4 cylinder
Took the drum off, backed down the tension on the adjustment screws. Drives and feels fine until the brakes heat up.
Well, I have a 2011 Ford Escape. Recently, the car has been making two noises coming from the right rear drum brake.
I can only hear it going 5 mph or lower, possibly from road noise.
First noise: It sounds like someone is rubbing wet rubber on a wood floor (weird analogy). Not a grinding sound like a bad pad, but more of a hard rubbing sound.
Second noise: Whenever the car is at 5 MPH or lower and starts to decelerate, there is a high-pitched very small whistle coming from the same area. The pitch decreases as the speed does.
Got the brakes checked, no issues.