Camry :: Power Loss On 2003 XLE / Not Accelerating Or Going Up Hills
Feb 11, 2015
My 2.4L 03 XLE with 220k on it is losing power. Running fine other than not accelerating or going up hills as well as it was last week. I have P420 cat code for the past 40K. It also has the typical smoky start from leaking valve seals and uses about a quart every 1k miles.
Ran a can of 44k through it and I'm about to pull the plugs and see what shape they are in, but I'm wondering if this loss of power might be the cat. I've been searching and it seems a plugged cat is a common cause for power loss. Seems likely since I use so much oil.
Seen the DIY replacement and leaky seals Rockauto suggested replacement Eastern ECOIII as well as the Walker.
View 14 Replies
Advertisement
I pulled with my 2000 F250 7.3 for the first time yesterday pulling a 12,500 5th wheel and then again today with an 18 ft ski boat weighting around 3500 for both the trailer and boat. I had this same issue pulling both.
Today when pulling the boat/trailer i was behind a slow moving truck and when we hit a hill with a passing lane i merged over and wanted to start passing him. We started off at around 45 mph up the hill and as I started pushing the pedal I wasn't gaining any speed and my rpm's didn't even get over 1500. It felt like a stall and continued that at around 45-50 mph up the hill (about a 65 degree slope). When I'm not towing the truck runs great, plenty of power and averaging around 16 1/2 mpg.
Only mods i have is a 6647 Napa filter, muffler delete and it's running the same 4 position TS tuner from the original owner. During normal operation I run it at the 75hp gain and when towing i use the 50hp gain.
In both instances i could see black smoke coming from exhaust when pushing the pedal but my rpm's wouldn't go up and truck maintained the slow speed going up the hill. Once at the top it drove normal and picked up speed without any problems.
View 14 Replies
Truck started just fine this morning, was driving for about 15 minutes and it started to lose power going up a gradual incline. I didn't even think of it really and so I just pushed the pedal in a bit and no increase in power, in fact it bogged down. I let up and went back to the gas and same thing. This was barely pressing the pedal down. I got to the top of the incline and started back down a bit and gained speed (dropped from 55-60 to 40 at the crest) up to 55, hit level ground and started to lose power again, and it felt for the life of me like the truck was fighting for every ounce of power it could get. Everytime I would step on it it would bog down again. I nursed it to an appointment I had, and when I got done with that I started back home. Same thing. It would accelerate from a stop up to 30 (I've always been a laid back accelerater) and when I would read 35-45 it would start to dog again. I got it back home.
2nd issue: On the way home I had to stop at a highway crossing on a slight inline. There the truck started to shudder a bit. and if I would just touch the gas pedal it would bog down. I played with it a bit and got it to rev a bit. put it in reverse got away from the intersection and let it idle a bit when It died. started right back up, no problem. would play with the accelerator and same thing. I finally got it to rev a bit and 2 footed it back home slipping from neutral to drive.
View 14 Replies
Getting DTC P0401 on my 2011 with 92K miles. First time I got the CEL, we were on vacation, so I read the code, took a screen shot, then cleared it. Called my normal dealer, setup an appt, verified that they thought the truck was safe to drive. Coming home from vacation, I was pulling the TT in my sig, and noticed significant loss of power on hills that I have pulled many times before that I couldnt even hold 55 on now. Transmission dropped into 4th a couple times, on hills that it would sometimes stay in 6th, or at most drop to 5th.
CEL stayed off for a week , and came back on again. The funny thing is that after a day or 2, the CEL went back out on its own. I read the codes the P0401 is still there as a stored code(I did not clear this time). Around town the truck drives fine, the only thing I noticed was the decrease in power when towing. Truck is at the dealer now. TECH "isn't convinced" yet that there is a problem. He is not finished diagnosing yet, and I am sure that he has specific tests to run, but I am starting to fear that I will be getting the call to come get my truck.
View 6 Replies
My issue can be while driving with cruise on, or accelerating, the truck just losses power, then recovers. At idle, the rpm can, but not always, fluctuate.
There is no "misfire" when it happens, but it just falls on its face. I have NO diagnostic tools, and my injectors are not stock, so I am unable to unplug my DP.
My thoughts are to unplug the ICP and give that a shot? Meanwhile, I will put in a order for a elm327
View 14 Replies
So my wife's 2005 escape has been slowly losing power over the past 6 months or so. I regularly change the oil, tried new spark plugs, new air filter and still it's lazy. I know it's not a race machine but it struggles on hills.
This winter it was having problems starting unless the accelerator was pushed to the floor. After a cleaning of the Idle control valve all was well again. It has roughly 72,000 miles on it and uses .5-1qt of oil between changes.
View 2 Replies
My 2004 Subaru Outback has had the head gasket replaced, the O2 sensor replaced, spark plugs replaced. Still I cannot go up big hills anywhere near the speed limit. I think it may be the catalytic converter is bad from driving it with a leaky head gasket.
View 5 Replies
I have a 2000 Ford Explorer with 188,000 miles on it. I bought it used with 110K miles and put a new tranny in at that time. Now, I am having problems. I don't know if it's the tranny or the engine. It looses power when climbing hills. It takes off really slow with no power and finally gets up to speed it switches gears the whole time smoothly but the engine just can't take a load.
The check engine light came on and put out 10 codes:
P1451 EVAP Control System Canister Vent
P1747 Electronic Solenoid A-Short Circuit
P0743-Torque Converter Clutch Circuit Electrical
P0750-Shift Solenoid "A"
P0755-Shift Solenoid "B"
P0760-Shift Solenoid "C"
P0765-Shift Solenoid "D"
P0135-O2 Sensor Heater Circuit
P0155-O2 Sensor Heater Circuit
P1409-EGR Vacuum Regulator Circuit Malfunction
Those are the codes and I don't know how one has anything to do with the other. I checked the dip stick on the tranny and it's clean. Juicy red and not shavings.
View 4 Replies
My 2003 Camry loses power and starts to hesitate or miss-like under load, but when cruising along not under load it runs smooth. There is no check engine light coming on.
I have changed the fuel pump and fuel filter in the tank.
I have changed the spark plugs.
I have added injector cleaner and fuel treatment to the fuel.
I have cleaned the air filter and air filter compartment.
View 7 Replies
I have a '95 Town car that has great a/c, except for when going up hills it shuts down. As soon as I take my foot off the gas, it comes roaring back.
I've checked the vacuum storage canister (black plastic box) on the left fender well, and it's o.k.
I've checked all the red, blue, green, yellow vacuum lines @ the heater control and the various bellows that they control for scrapes/ kinks and they all hold vacuum/pressure.
I've checked the main vacuum line coming out of the elbow behind the throttle body and it is new and o.k.
I occasionally get the infamous "low flow egr" code, but I think this is due to loss of vacuum that is required to hold it open. The egr is brand new, as is the pipe to the right bank exhaust pipe and we have 4 new o2 sensors installed too. Also the horse shoe shaped passage under the intake manifold elbow is squeaky clean.
View 14 Replies
We have a 2005 Toyota Echo, manual 5 speed, with 160K miles. Everything works fine except for when you are accelerating (can happen in any gear) and mainly uphill. I assume the primary condition is when the car is being pushed or under more load than just cruising, anyway, it will will make a low grumbling noise and simultaneously shudders as if it is going to stall. This happens in a jerky fashion and doesn't last very long but consistently under aforementioned conditions. We have 3 Echo's by the way, all manual shift (Echo friendly)...
View 4 Replies
It's a 2006 Ford F250 6.0 diesel with 307,000 miles on it. Up until a week ago it ran great but when I was in a drive thru I turned it off (to order) then turned it back on to pull up but the idle was very rough and the truck shook as I revved it up but it went back to normal after I saw a puff of white smoke. Ever since then every few stop lights I will begin to accelerate but there isn't any power and it shoots out a lot and I mean a lot of black smoke for a second then the turbo spools and it's normal.
Today though I turned a corner and began to accelerate after but I had no power at all it shot out an un manageable amount of black smoke mixed with very little white as I pressed the pedal. I put the pedal to the floor and the rpm were up to 2000 still no power I out it in tow hail still pedal to floor and now power! At this point I pulled over and called my dad figuring the truck wouldn't move anymore but I got no answer so I tried to go again seeing how ideas almost and and the truck worked fine small amount of lag but it ran made boost and worked until I got home. What could it be? I've heard maybe my turbo is bad maybe my egr valve but I'm just not sure.
View 10 Replies
2001 Hyundai Elantra GLS ... I don't know what is going on with my car. When I start it, put it in gear and try to pull out, it feels like there is a loss of power. A few seconds later, the power returns . I can push my foot down, and the engine doesn't rev, but then it's like all of a sudden the engine realizes I have my foot down and takes off.
View 3 Replies
Mine is 2006 with 130k miles. Just replaced fuel filter, air filter, cleaned air flow sensor and cleaned the injectors. The car still feels slow and it seems to eat more fuel than before. The spark plugs and the wires seems to be ok. No warning or error on dash is displayed.
When push the accelerator it takes a while to respond starting from stop position, and when the car is moving and try go faster it feels like lazy so I have remove the feet of the pedal and push it again so it respond quickly.
View 3 Replies
Air blowing noise that sounds like a disconnected turbo or hose. Loss of power accelerating and downshifting.
View 4 Replies
So I got a new tranny about a month ago. Everything works flawlessly. Until today.... Going up hills even small ones feels like I'm towing a house. No torque felling. In 3rd and 4th gear (automatic) it gains boost really fast and peaks at 28 lbs. and coasting downhill it slows itself down. I can go from 60 to 40 without braking in a half mile stretch. I fist noticed something was different when I started to drive home tonight; it makes a sort of whining or howling noise. I can't quite pinpoint where it's coming from. I'm tired of this truck but love it at the same time.
2003 125k miles New tranny New injectors New oil cooler and egr cooler Possible bad HPOP
View 9 Replies
1999 saab 9 3 loss of power going up hill and when accelerating, have had the catalytic converter replaced, the turbo thingy checked and blown out, the muffler checked and found no problem, It has been put on the machine at 2 different dealers and no problem found...
View 1 Replies
I have a 2003 Chevy Malibu, V6, 3.1, auto, 140k miles. Car started out with code 0420 with no noticeable symptoms, but then added code 0303 (miss fire cyl #3) with loud knock (mostly after warmup) and loss of power under load. Now internal loss of coolant (no puddles or external drips). Changed plugs and wires - no change - all plugs looked good with no sign of contamination. Questions - if this is a valve/piston/lifter problem (which would explain the knock, miss-fire and loss of power), why would I get the loss in coolant? If the loss of coolant is fouling plug #3 (which would explain the coolant loss, miss fire and loss of power), could that give me the loud knocking? I don't see how a valve/piston/lifter issue would cause a leak in coolant but I also don't see how a coolant leak into cyl #3 would give me such a loud knock. Do I have two different problems? If it is a leak into cyl #3, is there any way to tell if it is the intake manifold gasket (which leaked before and was replaced five-six years ago and which I could do again if I had to) or a blown head gasket (which I don't think I could fix or afford to get fixed)? Engine will occasionally get hot (but not overheat).
View 7 Replies
'01 Silverado with the 4.8, sitting at 160k right now. I'm starting to notice a loss of power in the truck, when pulling out and accelerating it doesn't put you back in the seat like it used to and when going up a hill you have to force a downshift to not lose 15-20mph... it just seems like I'm pulling an invisible trailer back there. The fuel pump is about 1 year old, fuel filter less than 3 months, plugs and wires are about a year and a half old, PCV valve about 6 months old, fuel pressure regulator about a year old..
View 3 Replies
My wife has had her 2010 3.5 Santa Fe since new. Over the past year it's been having a clunk develop when accelerating, happening a few times from a start until highway speed. The clunks almost feel as if one is driving over bumps - that's what I thought at first. The power doesn't seem to be there anymore either. I have been driving her vehicle the past three years and it was fine when I first started driving it. But the past couple years I first noticed a problem and it seems it is getting progressively worse. My wife now notices it quite a bit too.
View 1 Replies
It did this funny thing about 4-5 times over a span of about 24 hrs before dying and then won't start. It was like hitting the limit on a speed governed car.....sudden momentary loss of power..and it seemed to be when accelerating if that matters. The thing I'm sure of at this point is that the fuel pump is not coming on when the key is turned, I know that sound well, but also checked it at the external connector with a test light for thoroughness. I also found a blown fuse under the hood which coincided with a little smokey smell inside the car when the fuse was replaced and blew again.
There is no spark as well. My Haynes book says that the PCM is behind the passenger kick panel but I only see the eecv and it doesn't smell burnt. The IFS is good. There is power at the coil packs. Fuel pump relay fuse is good. Is it more likely the ccrm since it contains the fuel pump relay and PCM relay or could it still be the eecv? It feels like one part failed but is causing more than one "problem", no power to fuel pump and no spark.
View 19 Replies
