Camry :: Low Coolant Temp - Engine Code P0128
May 1, 2014
I have an engine code of P0128 (low coolant temp etc.) I now think it's because I no longer have an Engine Splash Shield under my engine and the extra air is cooling the engine. I took it off after backing into a snow bank like an idiot. At first I thought it might be that I poured green coolant into the pink coolant because I lost coolant cleaning the throttle body (120,000miles). This mixture supposedly causes clumping and clogs in the system etc. Since then I flushed the coolant system and replaced it with yellow coolant which popular mechanics said was OK. So I'm left with the question of do i change it again to the pink coolant (~$50 compared to ~$15 for yellow coolant, thats why i got the yellow) or do i get an engine splash guard? Or Both?
View 11 Replies
Advertisement
I'm getting a P0128 thermostat coolant below temp. Coolant level checks out. Temp sensor seems to work. It climbs to 160 and holds steady. I simultaneously had a thermometer in the top of the radiator. It went from 86 to 160 with with jump from 86 to 135 which corresponded to the temp sensor reading of 135.
I am assuming this is the thermostat opening. So, the level is right. The sensor is working and the thermostat appears to open and close. Why its throwing a code?
View 1 Replies
2009 Ford Explorer, 6 cyl, 4.0L, 74K. Read code w/scanner - "P0128 - Coolant Temp below thermostat regulating temperature". Assuming this is pretty straight forward but was wondering what the most likely culprit is (?thermostat?). Ironically, this code popped about a week ago, I cleared it and actually got my inspection sticker earlier today and then later in the day, the CEL came on again and once again, the P0128 code. The coolant level is perfect so I know there aren't any leaks.
View 5 Replies
2002 Camry 4 cyclinder. P0128 code - replaced the thermostat and coolant. P0128 code is now locked in. Lifetd the battery cable, but it is still there when I start the engine - or - it comes comes back immediately when I start the engine. Coolant temperature looks normal on the dashboard gage when I drive the car. What should I do now?
View 3 Replies
I'm getting a P0128 code on my 2003 V4 Camry. Autozone diagnosis says it's either
a) coolant low level
b) sensor not working correctly
c) thermostat not working correctly.
As part of 90k mile check about 3500 miles ago, the mechanic replaced the coolant. I didn't check the coolant after he had replaced it but I just checked it today and it's about 1 inch below the full level. Is this normal coolant usage considering that it's been about 3500 miles and 3 months since it was last filled?If the coolant level is okay, then how do I figure out if it's the sensor/thermostat?
View 10 Replies
I have a 2002 v6 Camry with over 270k on it. Today the Check engine light came on while driving on the freeway. When I got home I used my scan tool and it gave me the following codes.
P0128, P0440, P0446 and P0440, P0441, P0446 pending.
I understand that the 128 has to do with coolant temp and that the other codes are evap system related.
What I'm trying to figure out is what might have caused them to all occur at the same time. I know once with my 98 Camry it threw a P0125 which had to do with coolant temp issues but it also threw several other codes for a bad 02 sensor and the 125 was just a false code (replaced the 02 sensors and they went away). If this 128 is possibly a false code or if I also have a bad thermostat/sensor on top of an evap system issue.
Also. coolant level is good and I checked the gas cap and insured it was on tight, reset the codes and am waiting to see what comes back.
View 1 Replies
I have unfortunately inherited a 2007 Toyota Camry LE at the passing of an uncle. I recently purchased an Innova 3140 b diagnostic scanner which pulled up several codes. One of which keeps popping back.
P0128 refers to (according to innova).
Coolant Thermostat (Coolant Temp Below Thermostat Regulating Temperature).
I have replaced the coolant temperature sensor but the codes came back after a few days. I cleared it once again and the code reappeared that same day. I have a thermostat on standby ready to install if the fix requires such.
View 8 Replies
Few weeks ago I threw a CEL for an engine coolant temp. It went away and came back now as a P3081, I don't recall that being the code before. But from what I understand It is a simple sensor that I can replace myself. Car is running fine and not overheating.. it did however overheat the last time It threw a CEL but that was also stop and go traffic with AC on.
View 8 Replies
I just had my 1998 Passat 1.8T with 97000 miles checked since the engine light came on. It started this afternoon and the car ran just fine. I took it to an Advance Auto and after they plugged in the OBD tool it came back with the code PO 116. Engine Coolant temp CKT Range/Performance.
The fellow decided to clear the code and then the car would not start. I waited for about 15 minutes and the car started with some hesitation and the light was out. When I got home I let the car sit for a few seconds and it started perfectly like nothing ever happened.
Does that mean that the temperature coolant sensor is bad??? I have a Hanes manual and apparently is not too difficult to do. Would I have to partially drain the radiator?
View 1 Replies
I keep getting the same code for the check engine light of P0128. I have replaced the thermostat twice and the ECT sensor already. I do know know what else I can do for getting this fixed. I have checked the fans and they are working correctly. I have also checked to make sure there is nothing wrong with the head gasket. My car does not over heat, but it does take forever for the temperature gauge to rise. This is for a 2006 Hyundai Elantra. What else I can do?
View 2 Replies
My radiator gave way on the highway, and by the time I noticed it the temp had maxed out the gauge and all the coolent was gone. So, I only have 90k on my '94 Camry and I'm debating whether to tackle repairs and perhaps a rebuild if necessary. What's the likelihood that there's damage to the rings, bore, crank, valves, etc due to the overheat? How much repair am I potentially looking at and what can I check without a tear-down? I'd like to get it running again since I just invested in new struts, brake calipers and MS and tires (not to mention that it has been pretty-much worry-free until now), but I want to know whether it's even worth my while.
View 6 Replies
I recently had the engine light come up on my Hyundai Elantra 2003. I read the code with my cheap little code reader with the torque lite (free) app on android. It threw the P0128 code which means a faulty thermostat.
Here's the web link to all the details on the code: [URL] ....
I have checked the coolant level and its good. The strength of the coolant is good to -40 Celsius. The engine fan is not running at all. I recently changed the thermostat. I'm leaning towards faulty ECT. The car takes forever to blow hot air too. It has done weird readings in the past with the temperature gauge in the cab.
I just bought a infrared temperature reader of Amazon and want to check the temperature where the water comes out of the engine past the thermostat and compare it to the reading on the torque app readings. I'm thinking it won't match.
View 15 Replies
Got a 2002 GT with the NA 3.8 and 150,000 miles. The car has pretty much sat for the past 6 months, driven very sparingly. If it's been sitting for a while (like over night or longer) it will start no problem. If I turn the car off for a shorter period, it will crank but not fire. It will start only if I pump the gas as I'm turning the ignition.
In addition, on occasions it has died while at idle or coasting to a stoplight. After it dies it will fire back up no problem.
Fuel problem perhaps?
The "Service Engine Soon" light has been on for about a month before it started acting up. I had the codes checked at AutoZone and it came up with P0442 and P0128.
View 12 Replies
08 RX350 with ~100K miles. Two weeks ago the Check Engine/TRAC light were on, VSC light blinks, so I tightened the gas cap, and pull the negative and cleared the code. Hoping this is just a gas cap issue.
2 weeks later all those lights are back again, so my mechanic pulled the code and came up with P0128. He told me it should be the problem with the Coolant Temperature Sensor. The water pump, thermostat was replaced last year and coolant level is OK. No issue with coolant temperature and the car drives like normal. My mechanic cleared the code and told me to drive it again until the lights come back and he will pull the code again.
08 RX350 AWD
08 Avalon Touring
View 5 Replies
I was driving today when the CEL came on, I scanned the car which gave me 1 code: P1296.
I googled it and said it is possibly the coolant temp sensor?
The Engine temp was normal at 190' or just below even after quite a bit of driving today.
Would the problem just be the sensor or should I be looking for other problems as well?
The car is a 2002 B5.5 AWM 1.8T Tiptronic.
View 4 Replies
So my check engine light came on in my 04 jetta sw, and when I had the car read, it gave me a code that tracked down to be a bad coolant temp sensor. I bought the replacement part from my local VW dealership, installed it and the check engine light went away. Now about 2 weeks late it came back on, and I am getting a reading of "Coolant temp sensor high voltage". So it goes from needing replaced, then the replacement is running high voltage?
View 3 Replies
Threw a coolant temp sensor code yesterday morning:
16502 - Engine Coolant Temp. Sensor (G62): Signal too high
p0118 - 002 - Lower Limit Exceeded - Intermittent - MIL ON
Does throwing that code once mean I need to replace the CTS immediately or am I safe to clear the code and see if it returns? No code today after a 40 minute drive.
View 3 Replies
P3081. What the hell is this code. I think it is a coolant temp. sensor issue.
View 3 Replies
I recently got the solid check engine light for my 2003 VW Jetta 1.8T GLS. I used a bluetooth OBDII dongle and Torque Pro to pull the code P0118. This seems to coincide with my symptoms:
Car idle at start in park stays around 1100RPM then in reverse it drops to 1000RPM then back into park and it stays around 900RPM and keeps that at idle.
If I start the car then immediately reverse out of my driveway then the car has a very rough idle but if I wait around 5 seconds in park idle then reverse out of my driveway it is smooth.
My car dash thermometer stays pretty close to the bottom low then after about 4-5 minutes it shoots up to 190F and stays. Gas mileage is also very poor.
I looked up a tutorial which shows the parts needed and how to replace the sensor : [URL] .....
I removed the engine cover and believe I found the coolant temp sensor in the spot the tutorial shows. My question is if there is anything I should be aware of before attempting to replace this sensor that this tutorial doesn't cover? I took a screenshot of what I believe is the coolant temp sensor.
View 8 Replies
2001 3.0 XLT Ranger 2wd 4 door
Okay getting ready to trade in my Truck. So I removed all the extra things I put on there while I was in college, the amp, fog-lights, and analog oil pressure sensor along with their wiring. It was pretty easy minus removing the oil pressure sending unit part.
I had to unplug the MAF to move the intake out of the way while I was repairing a loose vacuum tank. But I forgot to plug it back in when i closed everything up. I started the truck and drive it about a half mile before I was able to pull over and plug it back in. Truck ran and shifted fine after that, but the CEL came on. P0119 Coolant Temp Signal Intermittent. Guy at Autozone said it was Intake Air Temp Sensor intermittent and I could just replace the part, but they were showing a separate part even though it is built into our MAFs.
So now the CEL is on, can get it to go away. Truck is a little jerky every once in a while, like a misfire, when between 50 and 60. Before all this the CEL was off. Now after I cleaned it up and removed some of the superfluous accessories, I get a CEL. I wanted to trade it in this coming weekend without having to take a loss because of the CEL or spend more money to fix it.
View 3 Replies
So i've had this volvo for about 6 months now.I knew when I purchased it that the two codes being thrown were p0128-Engine coolant temperature, and p0420- Cat efficiency Bank 1.Inspecting mechanic said it needed a new cat to clear the p0420....I went ahead replaced the thermostat and changed the coolant to "fix" the p0128, and cleared the codes, I think the jiffy lube state inspector did not notice the that the catalytic converter test was Incomplete when he passed it. Lucky me I guess.
But now I know that I'll probably have to fix before it gets inspected again. Eventually the p0128 came back on, so I went and got a new ECT sensor. Still doesn't clear the p0128. What am i missing? Coolant temperature sits at a 3'oclock position pretty regularly and quickly. Where to start on the p0420 besides understanding its the Pre-cat o2 sensor that is throwing the code, is there anyway that these are related?
View 3 Replies
