I changed combination switch (got from junk yard $40) and added relay (from dealer $24). now plug has power as I turn fog switch lights on/off, but my bumper is solid. there is space but it's solid bumper
1. which fog light to buy?
2. how can I mount securely.
I changed my dogbone mount over the weekend. Did not get a oem but got one from advance auto for 50 bucks. So I noticed a vibration when I'm in reverse or drive. I got some vids of the engine running. Could the cheap mount I got just be causing more vibration than the old one?? Which was cracked?
[URL].....
Just bought an 02' camry and the high mount brake light on the spoiler is half burnt out. Tried removing what I'm guessing is an LED assembly but the screws are stuck and the angle is really awkward. Am I going to have to replace the whole LED bar?
View 2 RepliesRear hatch will not close securely. It is "loose" and balks at being fully latched.
View 3 RepliesNot sure why but randomly one time putting my car into reverse, both back up lights seemed to not turn on and I don't believe they are broken or blown.
View 4 RepliesI have a round plastic disc and one side is tacky to stick to the dash. Are these things easy to remove off the dash years down the road? I'm also worried the circle will be discolored from the rest of the dash.
View 3 Replies2002 Camry with check engine light steady on and car shutting off when coming to a stop. Diagnostics revealed error codes P0440, P0441, P0446, P0442 indicating evaporation problem. Found broken closed canister valve. Had valve replaced and check engine light went off. Technician says VSC/TRAC lights were on also when he pulled the car in.
They had not been on before. Now the VSC/TRAC lights are coming on and staying on when the car starts moving. The code is c1336, something about yaw rate sensor. Is there something that still needs to be reset or does this mean that the sensor is bad and what and where is this yaw rate sensor?
Last week, my 2002 V6 Camry decided it didn't want to start when the key was turned. That was with my wife driving. By the time I got out there, the car was running just fine. She said it didn't turn over, didn't click, nothing.
Today, it did it again, but it didn't have that magic reawakening like it had last week. I tried jumping it to see if it was the battery, but it did not change anything.
Here's what happens: Turn key to run position, and the dashboard lights up.
Turn key to start position, and there's silence. The clock on the dash turns off (as normal), but the only noise under the hood is the sound of the starter relay making a single click.
Does that mean the next place to look is the starter Solenoid? Can I jump the solenoid like on an old car to see if that starts her up?
2002 Subaru Outback 4cyl auto trans 166.8K miles
Hearing a "clunk" lately when switching into reverse in the AM after starting the car. The transmission seems to drive completely normal otherwise. So I checked the trans fluid and it's fine. Then I started looking at mounts. Upper engine mount has about 1mm of play, lower mounts don't budge. Then I went to the transaxle mount and found that there seemed to be almost 2cm of space (can easily fit my fingers in there) between the stopper and the transaxle crossmember (picture attached). When I have someone put the car in reverse while I am underneath (obviously we have the brake / parking brake engaged so I don't get run over) I see this stopper move upward and can see the entire drive shaft move upwards also. Not just a few mm, but on the order of centimeters. I could not get the clunk to occur to see if I can hear where it comes from.
Is this space and movement in the stopper and drivetrain normal?
If it's not normal, could this cause the clunk to happen?
It it's not normal, should I have it repaired on this vehicle? Is it hurting anything / worth it long term?
If it's normal, any other advice on sorting out the clunk? It does it about 75% of the time I shift into reverse, but seems less likely when the car is warm.
I have a rear rattle that I cant figure out had the wheel off and levered and pounded on links bushings etc. How can I access the top strut mounts to check them? Nothing found on youtube. Original struts on rear show no leaks or broken spring. Bouncing car does nothing neither does grabbing the tire at 12 and 6 or 3 and 9 position.
View 3 RepliesI need to change the all support mount motor of my Camry 2003 v2.4l. but I don't know where find the best model or manufacturer.
View 2 Replieswhere to get it? I want to plug up my bumper holes and just put the plate on the tow hook.
View 14 RepliesI ordered a stock, LE spoiler to spice up my base model Camry. I read that it's installed through the factory mounting holes although, when I took off the interior trunk lid cover, I did not see any "existing mount holes". It actually looks like a tight squeeze/fit to get any type of tool to drill out or ratchet any mounting bolts down.
View 5 RepliesI have an '02 camry v6. My hazard lights started blinking when the car is off and aren't responding to the on/off button. When I turned the car on they stopped for a few seconds then blinked rapidly several times, then back to normal blinking. I tried disconnecting the battery and restarting the car. The battery is only a few months old. What could be causing it? Where is the fuse for it located?
View 1 RepliesI had a dead battery in my 2002 Solara. After I had it replaced the indicator lights on the dash would stay on. Also the fan blower will keep running if not turned off. So I have accessories running with the key in the off position. I have checked all fuses and they appear good. Bad ignition switch?
View 3 RepliesI have a 2015 F350 and with the long dark hours of driving, I want to put some auxillary lights on the front of my truck. I have a ranch style bumper on the front and I am thinking about installing a pair of flush mount LED driving lights. I was wondering, how well they work? I am personally thinking about the rigid flushmount hybrid driving/flood lights with the focused beam.
View 6 RepliesI have a 2009 toyota camry le 4 cyl with 170000 miles. I had my rear main seal replaced because there was an oil leak. Now after I got it back from the shop, there is a oil leak near the front motor mount and my engine had gotten louder when i accelerate. also it smells like paint or something inside my car. what did the shop do?
View 3 RepliesI was wondering if there was a DIY mod so I can have my foglights on with my parking lights and my high beams..
View 7 Replies2008 Camry Hybrid. Normal lights are dim. Auto on position results in no lights. A turn brings the lights on, but appears to be a "parking" position. High beams OK
The dealership has no clue - they wanted to sell new bulbs. They are barely bright enough to drive at night, certainly not 10% dimmer from age as they described.. (plus the auto on does not work ).
I'm new to modding and I've been having a really hard time finding a forum that gives a good DIY instructions on how to wire the map lights to function as the dome lights so they (the map lights) turn on when the doors are opened.
Any parts required (relays or anything else of that sort)
2012 camry se my question is can I make the fog lights turn on with my parking ligths ???can it be done and how
View 14 Replies