I took my car in for some wiring work on the headlights and when I got it back the aims were completely off and are currently so low that it isn't safe for me to drive at night. I spent last night searching for the screw to level out the cut off but had no luck finding one.
View 1 RepliesI suspect that I already know the answer but will ask anyway. In another lifetime I could adjust the headlights on my car (two spring-loaded screws on each bulb for up-down and side-side adjustment).
The low beam on my 2010 Camry seems to run out at about 30 yards. Some night I am going out and actually measure it. High beam has no problem as it goes forever. It just seems that the low beam does not allow me to see very far down the road. I have not asked the dealer yet and thought I would ask here first. Is there a way to adjust the headlights on these new cars with the total headlight system in one big package?
I just put in a new headlight for my 08 600hl. My issue is the head light is pointed downwards. Is there a thread that shows how to adjust the headlight.
View 5 RepliesRecently lowered the car and can't adjust but notice that the headlights need to be raised up a little. I have searched Club Lexus high & low for a 'how-to' on here, but all that populates is the 2IS threads, or threads for the ES and GS models. I am looking for the 3IS 250/350 F-Sport headlights.
View 1 RepliesI have recently purchased a 2006 V6 diesel with only 20,000 miles! Best car I ever had! I am driving it in France in August and want to know how to adjust the headlights (the bi-xeon), as nothing in manual. I am assuming there are some levers, screws to adjust behind lights?
View 7 RepliesI replaced some TYC OEM headlights on my car with stock OEM Hella headlights and cleaned up the lenses really nice.
Once installed, I went to adjust the headlights to find out that the passenger outer adjustment just spins.
This is the one in the photo:
I am not too sure if I can fix this. The little wheel doesn't seem like it can be removed and it has some back and forth play on it.
Need to successfully repaired headlight adjustment?
I am trying to adjust the vertical (up) AFS headlight aim on my 2010 RX 350. They currently point too low and do not illuminate the roads well enough at night. Note that the vehicle has the AFS HID headlights that are located next to the front grill.
The owner's manual provides do-it-yourself (DIY) instructions. Electronic version may be linked here: [URL] .....
I found adjustment bolt A elsewhere. Adjustment bolt B was found as illustrated.
Following these instructions on p. 512, I have tried adjusting the two silver bolts for the left and right AFS headlights by manually turning each pair of bolts on both sides with my fingers rather than a Phillips screwdriver, but no effort appears to affect the AFS headlight aim either vertically or horizontally.
The instructions also recommend taking the vehicle into the dealer if the headlights cannot be adjusted this way.
My headlight aim is all out of whack, the driver side light is aiming all the way to the passenger side. I searched the forums and know where the screws are for the vertical and horizontal adjustments. Counter clockwise for making the headlights go up and you're suppose to go the same direction on the horizontal adjustment as well. But my driver side headlight is aiming so far towards the passenger side already,I need to get the horizontal adjustment back to the left, which direction to turn? Clockwise or Counter?
View 2 RepliesJust looking for the correction direction for the HID headlight asm. Do you turn the screwdriver clockwise to raise the headlights?
View 4 RepliesFor those lowered, how did you go about getting the beam height back to stock spec?
View 1 RepliesTried to find how to adjust the headlight on 2014 IS250 since it was lowered on RSR Super Downs. Very hard to see anything up front with lights beaming down on the ground. I've tried to find it in the manual book, but it's not there. Found only DIY for 2nd GEN IS's. Seems like the 3IS is different from the previous GEN.
View 6 RepliesI had a low beam bulb go out a month ago on the driver side. I bought some silvania silverstars to install on both sides. The drivers side went fine but as I installed the passenger side the inside reflector housing came loose, apparently popping off some spring clips inside the headlight housing. The passenger side headlight assembly now pointed towards the ground 10 feet in front of the car... I tried to adjust the screws to bring the light pattern back up. No joy.
Anyway I messed and messed trying to get the reflector housing to fit back on the spring clips. I ended up having to pull the bumper apart and the whole front side of the car to totally remove the headlight assembly. Once I got it out I found these little ball/socket spring clips and was able to put the assembly back together.
Now my issue is I have lost track of the adjustment screws and where the headlights should point. Any formula such as, "park your car 10ft from the garage door on the flat level. The low beam should be 30 inches off the ground on the bottom and the 40 inches at the top. The beam should be 50 inches from the center line of the car" Something like that so that I can get my headlights back to factory settings.
I just bought a 2010 RX 350 with comfort package with USA spec. My car is imported into Asia country, and I found a very strange thing, now matter how to flip the switches, I cannot cannot power up those 2 lamps !
I borrowed a forum member's car picture below to illustrate my point. (BTW it is a very nice car)
Under what condition or switching method can i turn that lamps on?
[IMG][/IMG]
So I have ran into the problem of the left headlight flickering. It went completely off today.
View 4 RepliesMy driver's side bulb at times will just go completely off. Is it the bulb or the ballast shooting craps?
View 7 RepliesThe brake pedal is a little too high for my tastes, and I'd like to lower it a good inch. How I can do this.
I'm not sure if any Camrys come with adjustable brake pedals, but mine appears to not, and it's an XLE, which leads me to think they don't.
I've searched and can only find instructions/details on 6.4L and older Super Duty trucks. The process is the same to adjust the gear box for a 6.7L?
View 5 RepliesIt's not what I did, but what I would like to do. My headlights are aimed too low and I have not been able to figure out how to raise them.
View 3 RepliesIs there a way to adjust the windshield washer sprayers to point them up higher on the windshield. I looked today and didn't really see any way to point them up more.? Mine probably hit the bottom 1/3 of the windshield and do not do that great of a job. Maybe I'm missing something?
View 3 RepliesI have a 03 Solara with the 1MZ that has had the engine replaced with a 02 camry 1MZ. I bought it as a project, and have everything worked out, but I've run into a problem that I need solving. The power steering adjustment bracket is different between the two cars, due to the T-belt tensioner it doesn't have a stud to mount it too. It has the tensioner at a angle, not straight up and down.
View 2 RepliesChanging brakes on the 92 camryHow do i adjust them ??They have the auto adjuster but can i get them close before i put the hub back on or is it go in reverse and keep hitting the brakes.I used to know but i forget
View 19 Replies