Camry :: Gas Filler Flap Missing And Engine Light On - Code PO446
Oct 11, 2015
I have a 2003 toyota solara se v6 I got the engine light on the other day and I noticed the gas cap was not good so I bought a new gas cap from the deal and put it on then my engine light went off. But now after 3,3 days of putting the new gas gap it's back on again what I noticed now is I'm missing the fuel filler neck flap (little metal round thing ) it's where you put the gas nozel to fill the tank and also it's showing the code PO446.
View 4 Replies
Advertisement
I have engine light on and the code is PO446. just changed fuel filter on my 2006 5.4L f150. What the code means ?
View 1 Replies
It seems mine does open every time you press the button. You can hear some kind of motor noise but it not as loud has the noise it does make when it does open. Its intermittent .
Do you get at it from the truck? What is the Part number for a 1998 Passat?
View 3 Replies
Ive got a question for all you code readers out there. My dreaded check engine light has been on for about a month. I bought a code reader recently and checked it out. Two codes come up; PO401 and PO446. What these mean. My book says "Exhaust Gas Recirc. Flow Insufficient Detected" and " Evaporative Emission Control System Vent Control Circuit Malfunction". Which sensors, location on vehicle, etc..... this is a 97 5.4L Expedition.
View 9 Replies
I have a 2001 Chevrolet Prizm with check engine light showing PO420 and PO446 codes, what could be the problem?
View 1 Replies
Posted earlier with my escape randomly stalling at idle. Getting a code po446 along with po511. Only stalls at idle after warming up and letting it set a while. When you go to recrank it that is when it won't idle or if it does its at 500 rpms or less. Also after driving it today it smells like rotten eggs. Replaced the idle control valve with no luck. What could cause this?
View 2 Replies
So I swapped an R motor into my 20th anniversary GTi. It idles fine as soon as I rev it and the idle comes back down it starts breaking up and I get a code for exhaust flap no communication. Of course, there is no communication since I don't have one. Is there a way to code this out or to trick the ECU to make it think its there? As soon as i clear the code the car runs fine, even if I just turn the car off and back on, it runs fine.
View 24 Replies
I got the known p2015 code about a month ago and the CEL is on. Here is my situation though...I went and had my car tuned for an APR stage 1+ tune with stock hardware, everything was fine. I then upgraded to a catless 3 inch downpipe (ebay on that links up to the stock downpipe) and a short ram intake and decided to go to the 2+ to delete the engine code for not having a cat.
While I was there, the guy tuning my car said on top of the code for not having a cat, there was a code for my intake manifold saying that one of the motors for a flap wasn't working correctly. I left there expecting to see a code but it never came back on. After4-5 months, I had to pass emissions. Obviously you cant pass with the 2+(found that out the hard way) so I had to have it returned to a regular stage 1 with the stock downpipe. Still no sign of a code for the intake manifold.
I passed emissions and then put my downpipe back on, however, I decided to buy the 200 cell cat from 42DD to weld into my downpipe to save me from having to constantly get my car tuned just to pass emissions. After welding in the cat, I still had a CEL. I went to advance auto and it said I had a code p2015 Intake Manifold Runner Sen Sw Ckit Rng/Perf B1.
I went and got my car tuned to the stage 2 for the hi flow cat and the light is still on. My question is, do I need to replace the whole intake manifold or is there a possibility that I could replace just a sensor? I have a 2012. If just replacing the intake manifold will solve this issue, I'll probably just buy [URL] .... and replace it myself (assumable that's what I need ).
View 1 Replies
Now that I have VCDS, I see a problem I never knew I had ... An error on the Air Con. I am not aware of any issue, it appears to do what I ask it. I cleared the error and it appears to appear again on a scan.
On reading the self study guide this looks like it might be an obstructed flap for the recirculation. I will have a close look next weekend.
Address 08: Auto HVAC Labels: 3D0-907-040.lbl
Control Module Part Number: 3D0 907 040 J
Component and/or Version: Climatronic D1 2031
Software Coding: 0000001
Work Shop Code: WSC 01065 000 00000
VCID: 254B0F7DE8FA196
1 Fault Found:
01274 - Air Flow Flap Positioning Motor (V71)
014 - Defective
View 24 Replies
Car: Camry 2004 xle 2.4 L .
My problem: based on P0032 code I replaced both O2 sensors (before and after catalytic converter) ..
Am still getting engine light on and code P0032.
View 6 Replies
2007 camry 3.5q... I got my engine scanned and the code was p0057. I already replace my two oxygen sensor but the check engine light and check vsc system still on. What will i do?
View 1 Replies
Changing the oil in my wife's 03 Camry 2AZ-FE, I noticed a small scratch-like crack in the oil baffle that's attached to the under side of the valve cover. According to the interwebs, this is a known issue and in a worst case a chunk of baffle can break off and jam the timing chain. How concerned should I be? I'm thinking I should just monitor it for the time being and get more alarmed if the crack gets bigger or the baffle starts looking like it could separate.
View 7 Replies
It just so happens that I got my letter from the DMV telling me I needed to get my new tags, and this is an emissions test year for my car. I was buys the last few weeks so I figured this would be a good week to do it. Yesterday.......check engine light comes on. How does that happen???
So now I'm on a time crunch. I went to Advanced Auto this morning and they checked the code. It's P0440, an Evaporative Emissions code. Any thought on what that me be, or any checklist as to what to check first? I'm fairly handy, but know nothing about cars. I'm sure I can figure it out with some instructions.
Summary: Got a check engine code of P0440, Evaporative Emissions. On a time crunch because I need to get an emissions test done. I can probably fix it myself with some direction.
View 2 Replies
My wife's car has 83000 miles on it. We bought it as a factory certified pre-owned vehicle with about 1800 miles on it and it came with the warranty. For the last two years the check engine light comes on with code 441 I don't worry about it till time to get inspection sticker here in Texas. I have been about to reset the computer and drive it till the computer is ready to be inspected and it has passed for two years. Now it won't reset and I have tried to test the vacuum switch and it seems to click when I apply voltage but light won't go off. This code can cost up to about 2000.00 to try and detect. I am not interested in having the dealership keep guessing on my dime.
View 2 Replies
I own a 2003 Camry LE. I went to Autozone to find out what the check enginge light was for and was given P0031. When the service person checked it out on the computer he said the probable causes were:
1) open or short circuit conditions
2) poor electrical connections
3) failed oxygen sensor
4) EFI relay fault.
I asked how it could be narrowed down and he said it I would have to get the car checked out.
View 14 Replies
I'm getting a P0128 code on my 2003 V4 Camry. Autozone diagnosis says it's either
a) coolant low level
b) sensor not working correctly
c) thermostat not working correctly.
As part of 90k mile check about 3500 miles ago, the mechanic replaced the coolant. I didn't check the coolant after he had replaced it but I just checked it today and it's about 1 inch below the full level. Is this normal coolant usage considering that it's been about 3500 miles and 3 months since it was last filled?If the coolant level is okay, then how do I figure out if it's the sensor/thermostat?
View 10 Replies
2001 Camry 4 cylinder. Check engine light came on yesterday. Advance Auto pulled out the code P0446 for the evap. emissions system vent circuit.
The car has no symptoms other than this and is current on all maintenance, but obviously it is a 10-year old car and so it goes.
View 9 Replies
2003 Camry 2.4L 4cyl
I noticed my engine light turned on. I went to Autozone to hook the car up to the computer. The computer printed out the code P0420. My coolant temp is normal. What can this code mean. The car has over 126,000 miles.
View 14 Replies
2002 Camry 4 cylinder. I've replace the o2 sensor the one in "Bank 1". I've cleared the check engine light three times now and it still comes on about 30 plus miles. Do I need to reset the ECU? Or replace the catalytic converter?
View 11 Replies
Check engine light was on for some time when I had filler neck and cap replaced. Computer sensors did not re-set until 501 mile mark, when light came on again. Checking the web, I find that some who appear to have knowledge of problem say it could be hoses, sensors, valves, or evap canister--the charcoal canister.
Mechanic who did original smoke test and recommended replacement of filler tube wants to replace evap canister without checking anything else. What should I do? At wits end, and car needed to pass inspection 2 days ago. Car has 157,000 miles or so...
View 9 Replies
Today my check engine light came on and the code is P0712. When I drove off from the parts store, the check engine light suddenly went off. What should I do at this point? What are the most likely problems/solutions.
View 1 Replies
