Camry 2012+ :: 2014 - Running Sluggish As Power Loss?
Feb 26, 2016
I have a 2014.5 Camry SE 4CYL 29K . Lately the car has been running so sluggish, it almost seems like it has lost power. Acceleration from stop or while driving seems to be a burden almost like if i was towing a boat. I have 5k since since my last oil change, and have the KNN drop-in air filter, so dirty air filter is not the problem. Not to forget that I always pump 91 octane from chevron. Why this would be?? ( should i have them change the spark plugs?) or could this be due to the transmission?
View 14 Replies
Advertisement
I just got a 2014 Camry SE a few months ago. I have a couple of questions. First of all, I need to know how to turn off the daytime running lights when the engine is off and I'm just parked and listening to the radio. The lights seem to be on any time the ignition switch is in any position except off.
And secondly, is it necessary to use synthetic engine oil instead of good quality regular oil of the correct viscosity? Will it affect the warranty, how about the oil change interval, etc.
View 12 Replies
I took delivery of my 2012 FX4 Eco in January and about a month or so later I began experiencing a loss of power and the check engine light would come on then go off again. This happened the first time in Houston traffic one day so I was pretty concerned needless to say but then it cleared itself shortly thereafter. However, heading back home it occurred again on the highway while I was trying to pass and she just didn't have the power. I took it to a Houston dealer late in the afternoon before I left but no codes were found and when I got it back to my local dealer it was determined the left side catalytic converter was bad and it was subsequently replaced. Well, it happened again and it's back in the shop while I am offshore so they have plenty of time to take care of it.
View 2 Replies
I've been noticing severe power loss lately . I know the 12 camry i4 has a bit of lag when acceleration but it's a bit worse now . I do have weapon r header , injen intake and magna flow muffler. I've cleaned the intake filter but sometimes the car feels as though it doesn't want to go then it does. I have to push the pedal down hard . I also have res delete.
View 9 Replies
I have a question for everyone out there with any insight of the harsh shifting with these trucks. I have a 2003 f250 super duty with the 5.4l and 126,000 miles on it. The problem I'm having is some weird shifting that has been going on over the last six months and I feel like I am just throwing money at this problem. My truck shifts hard from 2nd to 3rd and from 3rd to 4th with the most violent shifts being from 3rd to 4th! Between shifts is where it Is sluggish I mean if I am not on the throttle from those shift points I switch from driving a truck to a geo metro it is night and day with the felling of loss of power!
I have had it scanned at my local ford dealership and had a full diagnostics done and all I got was "it's since truck and a nice bill to come with it" they couldn't find a thing. So far I have all new motorcraft plugs, cops, changed fuel filter, had my catalytic converter checked if it was clogged,run on two different power balance tests! Still nothing! So now I'm lost I have heard things about these trannys and the lock up but I was told this only had to do with overdrive and it wouldn't happen at other gear changes. I still drive it everyday I have just figured out ways to calm it down if I stay off the gas when it's about to shift for a couple seconds then get back on the gas it is like it never happened.
View 11 Replies
the 12V power charger by the cup holder in my 2014 camry stopped working. I checked the fuse and its not blown. Is it the actual socket itself I fried?..
View 4 Replies
I have a 2000 ford explorer. 4x4 v6. One day i started it up and it was running rough. It had real sluggish power. Then the check engine light came on. I hooked it up to the code machine. The only readout was number 3 misfired. I replaced the plug and all was fine. A few months it happend again. I replaced it again and it was fine. Well it just happened again. I replaced it again. It ran good to work but on the way back no good. Light came on again. Hooked up the machine it read number 4 misfired and number 2 bank lean. So I replaced number 4. It still runs like shit rough idle and no power. Give it gas it dogs out but then it'll kick in if i get on it. Thinking it maybe a vaccum leak or intake leak or o-rings.
View 4 Replies
I am still trying to debug my 7.3 running sluggish in the 1200-1800 rpm range. The problem is intermittent. I checked the wiring harness under the valve covers to verify they are plugged in and there are no opens in the circuit. I replaced the crankshaft position sensor and the high pressure oil sensor.
This will run fine one time and a few miles down the road it will chug and smoke out the exhaust until I either get into the accelerator or back off and re press the accelerator. Again, it does it intermittently hot or cold.
I ran both a cylinder contribution test and perdels with a Snap On Verus. The cct passes everytime. The perdels have a couple of cylinders 5-6 and 8 fluctuate between 0 and 1.80% with #8 up to 2.5%.
My question is. Do the cylinders in the test correspond to the actual cylinders in the engine? Reason I am asking is the Verus does not follow the firing order on a gas engine. The cct is in order of 1-8 and I have to correlate the cct order to the firing order. Found this out the hard way when I had a bat cop on a 5.4 and replaced it only to have the same cylinder still show not firing.
I got out the graph leads and tested the cylinder and pulled the injector thinking it was bad. Everything showed good but the cct still showed it not firing. I had to unplug each coil and watch the cct to determine what the true cylinder in the test was. It turned out to mimic the firing order so I am asking out of concern that cylinder 3 in the perdels is really cylinder 3 or a different cylinder.
Btw, the perdels all show 0% if the transmission is in drive. I would have thought that a load on the engine would have showed higher perdel percentages with a load on it.
View 13 Replies
Lately I have been having problems loosing power. Truck wants to miss mostly going up hill and runs sluggish I'll pull off the road and let it idle for a minute and it will run fine. And it is only occasionally some days it don't happen at all and other days it happens quit often. New fuel filter, oil is good, had it on the scanner and isn't throwing any codes. Around 230k miles newer injectors.
View 10 Replies
My 2003 6.0 truck lost most of its power. It has the SCT programmer. It used to run great it would roll coal really well then it slowly started to run worse. Now it runs really sluggish especially when its cold. IT takes forever to warm up. On the freeway when ur going a constant speed it bucks and jerks a lot. It won't roll coal anymore and just runs like crap. A mechanic said I had 3 bad injectors. But I don't believe it.
View 2 Replies
I have a 2011 F250 6.7 that I bought in August of 2010. I have 35K miles on it and it has pretty much been trouble free once I got the firmware update for the shifting issues. I have the local dealership do all of my service work and all updates and service bulletins have been applied. Unfortunately on my way to work this morning the stupid Check Engine Light came on. The dealership has it now - hopefully I will know tomorrow.... I do think it has been running a little sluggish but I am not sure if that is the winter grade diesel (I use PM22-A in every single tank).
View 2 Replies
I have a 2001 ford 7.3l powerstroke diesel. When I first noticed the problem I was towing a trailer going up a grade and got into the throttle almost to the floor and noticed a loss of power and the service engine soon light flashing extremely rapidly a few times and never came back on. I made it home, still lacking power but not running rough. I drove the truck to work the next day and the truck was running rougher and loosing power. It ran great through lower RPM's but seemed to trip as soon as you gave it over half throttle. eventually the truck wouldn't run right at all and lacked complete power. It idled rough as well. My mechanic threw the computer on it and it said injector pressure reading too high or too low.
I was told to replace the IPR on the HPOP and I did. (I also replaced the fuel filter and changed the oil). After replacing the IPR it ran great, had full power! then it began to slowly die like it did before until it sounded like it was running off 4 cylinders again. I pulled the ipr out, cleaned it and changed the oil again. It seemed to clear it up for an hour and ran great but then began ran rough again. I also replaced the CPS sensor. I feel like its not getting enough fuel or something, im just wondering if it could be the ICP or the lift pump. There is no check engine light at all. Its just got me stumped because cleaning the IPR clears everything up.... temporarily.
View 14 Replies
I can't find the button to reset the TPMS light on my dash. It's not even in the glove compartment.
View 7 Replies
why my truck is running rough the problem I am having is when you push the gas peddle more than a 1/4 of an inch it shudders and has no get up and go and also if say I'm doing 40 MPH and hit the gas you can hear the engine rev up but I will lose all power and actually lose speed I thought maybe the cats were bad and I changed the plugs for good measure but I can't seem to figure it out also I had the fuel pressure checked and its pulling pressure is great/
View 6 Replies
My wife's 2000 grand am 2.4L engine is acting really funny. this is the first problem we've had with it. i was driving it to pick up my kids from school. on the way i stopped and got some gas from the marathon then drove about 5minutes and it started running really ruff lose of power wouldn't go above 30mph seemed like the transmission took longer to shifter to.
i made it to the school as i was about 2 1/2 blocks away. got my kids check the oil and it was really low so i got 2 quarts as it was a gas station in walking distance. i thought it was a lil better but i started driving it and it had the same results. i got it home about a 10minute trip regularly and parked it.
the next day day it ran then stumbled hard. and every time i tried to start it got the same think was like a lock up. it did crank but when it tried to start it stumbled or locked up. i pulled the plugs had some wet threads oil was on the first on and the threads and around the spark plug b4 i pulled it out.
2 of the other plugs had red stuff on them not on the threads though. here are some pictures also i will show a vid of what its doing. i did a compression test and here are the numbers starting with the first one with oil on threads.
190-194-200-190+ compression test with cold engine.
Also smoked puffed up not sure from where yet..
View 19 Replies
So I got everything fixed on my 94 ranger so I thought. Now it runs right on the "L" on the idiot gauge on 90 degree plus days running the AC. Also it seems to lose power at times and not even want to do 70. I think new coils, new plugs and wires may work. I also have an intermittent check engine light that pops up on occasion, but clears when you kill the motor and start it back up. I was really starting to like this truck despite it not being my style(I like square body rangers) and it being a 4 cylinder. I like the MPG but am starting to think the 200k engine may be fading
View 14 Replies
I have a 2012 F-250 6.7L w/8K miles. I have been struggling with this issue for 6 mo. The engine feels like its missing at low RPM. I would equate it to the feeling of a bad coil pack in a gas engine. The boost indicator drops to 0 for a split second then recovers. The dealer says they can't find the issue but went ahead and replaced the turbo. After the turbo replacement It got worse. This is an intermittent problem with no codes.
View 14 Replies
I am a new owner of 2012 VW Tiguan basic model. I noticed that AWD was replaced by 4Motion was told it is AWD in VW. I drove two AWD (Outlook and Edge) before but they are quite different from I have now with this Tiguan. When driving less than 50 mph, it is perfect and normal. I fell no difference from I had with previous AWAD. However, when speed exceeds 60 mph, I can feel the "active driving" control kick in to intervene my powertrain. If you sit entirely on your seat, you can feel the car body try to swing a twist occasionally, it come and go and let me feel the car is running unstable. I actually have an advanced degree in ME and have been working on auto industries for years. But this is strange to me. I have some theory below:
1) something wrong with 4motion, it activates too fast or violently to cause tail twist (it is like you brake one rear wheel as tag and go style, so that your car still go but your tail swing a little bit)
2) unbalanced rear differential (due to dirty debris or grease?) such that one wheel has more resistant drag than the other? As 4Motion activated thru multi-disk clutch, the abrupt force cause two wheel rotate at slight different speed to swing the rear body? BTW, are these multi-disc controlled by on-off type or PWM? and at what speed, it activate? My previous AWD seem to be passive type with purely hydraulic to pass torque.
3) miss-calibration on the 4motion activation map? is there a way to smooth the clutch locking mechanism by sequential locking or increase the locking period? VW AD said about timely 4 wheel drive mechanical system. I would like to what timely means in this incidence?
4) Either front wheel aligned such as not enough toe-in or toe-out? I just have the car for one week. I plan to bring it back to check for remedy. Or 4 wheel miss aligned? but it is hard to explain why the car run normal under 50 mph?
My car is 2012 VW Tiguan with 40000 miles, turbo, basic trim and no navigation. Not even a compass? It does have a nice white car body to show if the door is open.
View 5 Replies
About three nights ago I had a complete power loss on the highway and the car began to bog down alot under throttle (and surge at points as well although with no boost). It also idled very rough/erratically. When I unplugged the MAF it cleared up right away; Idle was smooth and it ran without hiccup but in safe/limp mode so very tame (again, without boost really, gauge shows it stays in Vacuum and never passes "0" or goes into boost).
I scanned it this evening and got 2 misfire codes and a MAF code, along with a code related to traction control which I noticed had activated as a result of this and could not be turned on (by activated, I mean the light came on, disengaging T/C). These things make me think it is MAF related, especially because I have bolt down Hitachi coil packs so I do not think that is what it could be in relation to the misfire codes (which I think may be old and needed to be cleared).
Fast forward to last night: I can pretty confidently say my MAF is not the problem and I think I saved an unnecessary expenditure. I was able to meet a friend with a 337 as well and his MAF did not change my car at all and my MAF ran fine in his car so I think my problems are something else. Although with the MAF plugged in my car runs very poor and unplugged it clears up and just runs "limp" (no boost and slow but stable) from what I tested this evening the MAF unit seems to not be the issue.
I think there must be a vacuum leak of some sort between the MAF and the engine which allows more air in than the MAF signals when plugged in which causes the issue. Also, I know a common thing to think is "coilpacks" but I have bolt down Hitachi coil packs so I would imagine that would eliminate those from being the failure they tend to normally be. Agreed ??
View 14 Replies
OK, I have looked everywhere I can think to look and can't fined anything on this. Dash lights how do you turn them off with the engine running. This is on a 2012 f150 xlt.
View 4 Replies
I have a ford fiesta that first of all started off stuttering/loss of power and now wont stay running when the engine is cold ...... 1.4 54 plate ....
View 4 Replies
