Camry :: 2011 - Plastic Engine Cover Removal
Dec 27, 2015
How do I remove the plastic engine cover from a 2011 Camry ?
View 2 Replies
Dec 27, 2015
Advertisement
Camry :: 2007 V6 - Plastic Engine Cover Removal?
I have a 2007 Camry XLE V6 that needs new spark plugs and the first thing to remove is the plastic engine cover. I do not see any screws or bolts attaching it down and I would like to know the proper way to remove it without damaging it or the plugs holding it down. How to do this?
View 3 RepliesCamry :: Some Black Carbon Came Off While Removing Top Plastic Cover
I recently removed the top plastic cover on my '05 Camry LE V6 to pull a plug and inspect/decide if I was going to change them out. While I felt I was being careful handling the plastic cover, I grabbed it by the access hole for the oil filler cap. Walking back into the garage, some black carbon came off, and looking at the bits on the ground, and what was left on the inside of the cover, I'm not sure if there is supposed to be a gasket there.
Maybe it was just an accumulation of spilled oil over the years that has trapped and "cooked", or something put in place to capture spilled oil. I scraped the rest of the carbon off using a razor blade and cleaned it up before installing the cover.
Golf/GTI VI :: Oil Dripping On Plastic Cover When Looking From Engine Bay
This morning after pulling out of the garage, i notice a small wet spot on the floor, went to see what it was and it was oil, its was a wierd shade of red/orange and very clear, def not engine oil. Then looked under a car and saw it where it came from, front driver side, there is a some kind of plastic cover, it was collecting there then dripping out. I can see the oil dripping on the plastic cover when looking from the engine bay? What can it be?
View 4 RepliesCamry :: Rear Bumper Cover Removal?
how to remove it.My wife backed into my truck and put a dent in the corner of it so I am hoping i can pop it out.
View 4 RepliesSonata NF (2006-10) :: Engine Cover Removal
I'm having trouble removing the plastic engine cover on my 2008 Sonata. I removed the two 10mm nuts on top and can raise the front part up, but the rear won't release...so what's holding it on and how do I release the rear side?
View 2 RepliesPassat (B6) :: Proper Engine Cover Removal?
Here is an image of how to properly remove the engine cover.
View 4 RepliesPrius (2004-09) :: How To Remove Plastic Rim Cover
I got a piece of cable tie stuck in there.
View 6 RepliesPrius (Gen 3) :: Unrecognisable Loose Wheel Well Plastic Cover
I have a 2012 Prius. I occasionally will clean the wheel wells, as I live on a dirt road. I have found that there's a plastic cover inside the left rear wheel well, at about 2 o'clock as you face the wheel. It seems to be loose.
View 3 RepliesGolf/GTI VI :: Plastic Creaking / Noise On Sunroof Cover?
Having problems with sunroof cover making noise when going over bumps? It just sounds like the plastic is making all the noise.
View 8 RepliesPrius (Gen 3) :: One Side Of Bottom Black Plastic Cover Was Drooping
I just joined up after purchasing a CPO 2010 Prius IV. Love the car but after taking a closer look I noticed that one side of the bottom black plastic cover was drooping on one side. Upon closer inspection I noticed that there was a screw and plastic Grommet combination that was not locked into place. After unscrewing the screw, I tried to put the grommet back in place but noticed that it couldn't fit because (I believe) the white bumper portion where the grommet goes broke off. I compared it to the other side of the car and yes it does seem like part of the plastic top portion that is connected to the bumper broke off.
I inspected the bottom some more and it seems like there are a good number of screws missing and a large plastic piece that is the front tire well is also very loose.
Prius (2010-12) :: Clips Holding Plastic Cover Broken?
I opened the hood today to install the Carbon Fiber logo and noticed that the plastic cover sitting on top of the radiator was loose. That's when I noticed that the 2 clips holding the plastic cover were broken.
View 3 RepliesFord Excursion :: Remove Plastic Cover In Front Of Radiator?
I took the plastic cover in front of the radiator off to clean the radiator and condenser. It directs air through the condenser before it gets to the radiator and I was wondering if it would cool the engine without it (if you don't need real cold ac air) . Without it the air can go over the top of the condenser and it is still blocked by the flap that stops airflow above the radiator. Also, I am wondering if the fact that the condenser has nothing in it affects the radiator cooling, and is it bad for the AC system to be empty. (My AC doesn't work)
View 7 RepliesLexus GS 2013+ :: Plastic Cover Over Navigation Display Dirty On Inside
I just took delivery of a 2013 Lexus GS 350 all-wheel-drive. I have the luxury package which includes the large display screen in the center of the dash. Unfortunately the plastic cover over the navigation screen is dirty on the inside. How to remove the plastic cover on the center display?
View 11 RepliesLexus GX 2004-09 :: Back Up Plastic Cover Of Driver Side Is Cracked
Noticed that my drivers side back up plastic cover is cracked with a small hole in the top. Would like to RTV the damaged area to seal it but I need to remove it to make the repair. I've pulled some of the inner plastic on the door but can't get at the back up plastic cover.
View 1 RepliesTiguan :: Lower Exterior Door Plastic Molding Removal?
How to get the plastic exterior molding on the base of the doors off. I see 2 screws and thats it. Is there a trick to it? I need to replace the passenger side or epoxy one of the clips back on then remount it.
View 2 RepliesFord Excursion :: Removal Of Rear Plastic Piece From The Glass?
Mine is peeling like I know they all do and I want to sand it and re-paint it. How exactly does it come off?
View 8 RepliesPassat (B6) :: Creaking - Plastic Dash Trim Removal On Passenger Side?
How to remove the plastic dash trim on the Passenger side? Is there a way to do this without removing the glovebox? I know there is one screw that needs to be removed. Mine creaks pretty badly. Ive already removed the center console trim and added felt to all those pieces. No more ticks/ creaks.
I guess I could have the dealer remove it but I dont want them taking my glovebox out to do it = more rattles. Why does VW make it so difficult to remove something that should be so simple!!
Ford Ranger / B-Series :: 1994 2.3L - Coolant Leak Coming From Under Black Plastic Cover
I noticed green coolant leaking from bottom of black, what I think is called, timing belt cover. There is 188, 000 miles, and when I changed the timing belt, I did not change the water pump, although I did change out the thermostat. I have done a lot of work on this truck in the past. I checked the oil and no signs of water or coolant mixed in. The water pump is not weeping from the top well. I rely on this truck and the way I look at it is I may just keep driving it until it goes kaput (its real beat up). Should I go to an auto parts store and see if I can buy some sealant. I would guess it is either the water pump or maybe the timing cover gasket? I have inspected all hoses, and I see nothing. The leak must be coming from somewhere under that black, plastic cover. I am capable and willing to do just about anything other than perhaps a full engine pull, although I have the wherewithal to do that too if absolutely necessary.
View 9 RepliesFord F-150 (2009-2014) :: Winch Mount Installation - Removal Of Plastic Molding?
Installed the Rough Country winch mount yesterday. One hour, by myself. Used a floor jack to lift it in place.
Only problem was removing the plastic molding which came in the spot the fairlead will be. Just a small rectangular plastic molding with a couple of bars down the middle for looks. It had two screws on top edge, and two pushpins on bottom , but also was molded with two catches on each side on the back I did not see. When I figured it out, and squeezed with just my fingers, little too hard and snapped one catch on each side. They slide into a slot and catch but wont be doing that ever again. Oh well.
As for mount, solid and easy to install. I used hand tools as the air gun would only hit one of the bolts for the front tow hooks. The other was blocked by plastic molding. No big deal.
Hidden Winch Mounting Plate for 09-14 Ford F-150 Pickup [1010] | Rough Country Suspension Systems.
Ford Super Duty (1999-2016) :: 2012 - Removal Of Plastic Tailgate Cap?
Looking to sell my '12 F-250 turbo diesel Lariat. She's in great condition, and only 8000 miles. Her only sore point is some scratches and scuffs on the plastic cap on the top edge of the tailgate (see picture below). I think it's part # BC3Z-9940602-B.
How to remove this cap, preferably without breaking/scratching anything else. It looks like there are no external fasteners, so I'm guessing it's just held on with clips on its underside, or some such. It might be more obvious once I get and examine the replacement part, but just figured I'd ask.