Camry :: 2009 Toyota - Front Brakes Clunking / Knocking After Replacement
Jan 11, 2016
I changed the front brake rotors & pads on my wife's 2009 Toyota Camry & everything seems fine except when doing sudden or slightly hard stops it seems to do a clunk/knock type sound from the front brakes. It also only does it sometimes not every hard/sudden stop.
One thing that comes to mind is that when I went to tighten one of the guide pin bolts it was a real pain, the big bolt that the screw threads into kept spinning making it hard to tighten the bolt into & none of the others did this. I thought I tightened it down but possibly not?
View 5 Replies
Advertisement
2009 Camry SE V6
103,000 miles
New Monroe OESpectrum struts installed by Sears Auto in July, with new alignment. Original springs were not replaced.
Soon after I heard a clunk. Sears tightened a strut mount a week later. Clunk went away.
New Kumho Ecstas installed and balanced a week later.
Still hearing clunk sounds from front end, take it back to Sears to inspect the struts and suspension. They tell me struts must be removed and inspected. They ended up not removing the struts but they replaced the sway bar end links and bushings, which they said were in bad shape. Steering is a bit tighter now.
Im still hearing clunk sounds from front end. Now theyre louder. I get a clunk every time I brake in traffic or a parking lot. I also get a clunk when the car goes over a bumpy road without brakes applied. So doesnt appear related to brakes, calipers, and whatnot.
I can feel the clunk in the steering wheel. Sounds like two loose parts rubbing against each other which shouldn't be rubbing against each other.
View 5 Replies
My 2002 Toyota Camry started making a clunking sound near the front left of the car (and I could barely feel it, too) at low speed over slight bumps. My mechanic, who I trust, said I had two broken engine mounts. He replaced them. Sound continued. He said I needed new struts. He replaced them. Sound continued. Decided to take it to a Toyota dealer. They said I needed new lower control arm bushings but couldn't guarantee that was the source of the sound and they would just have to see. I opted to ask yet another mechanic, who said the control arm bushings are NOT the problem, but he would have to spend some time (could be several hours) exploring to find out what the problem is...at $70+ per hour. The car only has 86,000 miles on it, but I'm getting concerned that I might end up paying for a new car without the new car smell if I keep spending money on "possible" causes.
View 12 Replies
I have a 2009 Toyota Camry. I started hearing this knocking noise(really loud pop) from the rear. I have read the TSB's about a knocking noise coming from the "Spring Bumper" from the strut assembly and they are all facing the correct way. And there was also a TSB for a knocking noise from the "Roof Structure." The dampening bonds come apart and makes a knocking noise. I've replaced a strut mount in the right rear and that did not fix the problem.
View 4 Replies
My wife has a 2005 toyota camry with about 84000 miles. She had been complaining of intermittent issues but no one could find the cause till yesterday. Her front brakes were froze and would not release. I took it to the shop and they said the left front was hung and the pad came off and chewed the rotor up. They suggested a brake job. Well in the process of replacing rotors and pads on the front they could not get the caliper to release. Make a long story short, the rotor and pads are changed but the front brakes will not release. They checked the lines and they look good.
View 7 Replies
My husband noticed that our 2001 Camry was driving strange. He thought it was a problem with the brakes locking up. When I drove it, I felt like the front of the car was a little wiggly and thought we might need an alignment. When we took it in, they said that the brakes are okay, but that the front struts are "soft." They said that the front struts need to be replaced, which includes an alignment, and we should replace the rear struts at the same time. They said we should get new tires at the same time.
I've been trying to research it some, and we don't have a lot of the problems associated with bad struts. We haven't noticed any bouncing or anything like that. I think they are honest mechanics, but my husband doesn't trust them. We don't have enough money to get all that work done right now, so my question is, can we wait until we notice bouncing or the tires get worse to have the work done? (We would be trying to save up the money in the meantime.) Or, can we just take care of the front struts and wait on the tires and rear struts? Should we just get a second opinion? (The car does have 145,000 miles on it, and I've never had the struts replaced. I bought it with about 65,000 miles on it.)
View 7 Replies
I got a horrible clunking/knocking in the front end of my pickup this morning, jerking the steering wheel like a flat tire, and after a couple miles it stopped..... bearing ???
View 7 Replies
So i had air-ride installed into my R 2 weeks ago and lately, i've noticed a knocking/thud noise coming from the front wheel well almost. I feel it more at low speeds and when applying the brakes to come to a stop.
View 4 Replies
Info: 2003 Ion-1 165k+ miles
I'm hearing a clunking/knocking noise in my Ion that sounds like the front driver side. It's most audible starting about 30 mph. It grows louder as I drive faster and the rate of clunking/knocking is relative to the speed I am driving. It doesn't change when I push in the clutch or when I'm in a different gear. It does not happen when I rev my engine in neutral. I even shut off my car while moving in a parking lot and no change. The sound changes when I turn (sounds like a more muffled/dull sound but still loud if that makes sense), and in my mind it seems to sound worse when I'm turning right than left.
I noticed the noise on Thursday of last week. It was at the point where I had to have my radio off to notice the noise. Since then it has grown louder and as of yesterday is now overpowering my radio when at reasonable volume.
I just replaced both the driver and passenger wheel bearing in the last 18 months, and I just got new Tier-3 Cooper tires 3 months ago. (I wouldn't think the bearing would knock, but just as history fyi.) I was convinced by the troubleshooting guide in my Haynes manual that it was either the inner or outer CV joint so I replaced the whole Driver side CV Axle and topped off the Tranny Fluid with Dexron-III. No dice. I thought there's a chance it could be my new tires, so I Rotated the tires on the left side F->B/B->F as well and the noise did not seem to change. Spinning the tires by hand while up on my jack stands does not seem to tell me anything (I'm guessing I'd have to have them spinning at about 20/30mph to hear anything).
My next idea at this point is to put the front end up on jack stands and have someone put my car in gear and give it a little gas while I stand nearby and try to pinpoint where the sound is coming from. I'm a little leery about this one, and I'm not even sure if it's going to make the noise when not under load anyway.
View 3 Replies
I ran over a rather large pot hole while driving home in the middle of the night. It destroyed my tire and tire sidewall and soon after the strut started to make a knocking noise while going over bumps. I replaced both front strut assemblies with Monroe Quick Struts (photo attached). After the install, the noise was gone and everything seemed good so I gave the car to my wife. After several months, I decided to drive the car to see if everything was still OK and it wasn't. The knocking noise on the driver front strut came back.
I took the car back to my mechanic and he said that he thinks the strut assembly was defective and that I should get a replacement since it was under warranty. I would just pay labor again for him to change it. Something seemed off by the conversation, so I decided to take the car to another mechanic for a second opinion, but before I do that I want to pose this question here. What could be the problem? Why did the knocking noise come back?
I've attached more photos. You will see two photos of the tops of the strut assemblies from under the hood. The first top photo is of the passenger left strut that is good (with the wheels straight). The second top photo is of the problematic driver front strut. You can see the top is slanted left with the wheels straight. The rest of the photos are from around the driver side wheel.
I did complete a wheel alignment after the install and the car pulls left when the steering wheel is straight after the alignment.
More information about the Monroe Quick Strut: [URL] .....
View 5 Replies
I drive a 2013 4 door gti. Car has 4k miles. Just last weekend myself and my buddies threw my coils in. FK Silverline X plus'. I am not sure on the measurement from fender to ground but I am a finger gap in the front, and fingertips in the rear. After throwing my coils in on saturday, I had an alignment and the rear camber adjusted. Just today, sunday, while driving home I heard a weird clunking/knocking noise. Previously I drove a mk4 and I know the sound of sway bar on axle and this is not the sound. Its coming from the passenger side front.. and I can sort of feel it through my clutch and brake. After pulling the car over I checked everything I could. wheels are all tight, struts seem fine. The noise occurs continuously even on smooth roads. The knocking/popping is pretty loud and can be heard in cabin. My buddy had mentioned the guys the aligned my car might have forgot to tighten something so I am heading back to the shop first thing in the morning.
View 3 Replies
I have a 2009 toyota camry le 4 cyl with 170000 miles. I had my rear main seal replaced because there was an oil leak. Now after I got it back from the shop, there is a oil leak near the front motor mount and my engine had gotten louder when i accelerate. also it smells like paint or something inside my car. what did the shop do?
View 3 Replies
I've got a 2000 Accord. I recently started hearing and feeling a hard knocking/clunking noise at the front-center of the car during the correct after a left turn. My trustworthy mechanic told me the subframe is rusted out on the right side and that it isn't safe to drive until the subframe is replaced (he also said he's seen several of these this last year). He suggested that the cause is that the hose leading away or down from the air conditioner is too short, and leaks directly onto the subframe. There is no recall on this problem currently. I've done some Internet research and there is some buzz about this, but not as much as I was hoping for.
View 17 Replies
I have a 2003 Toyota Echo. About 6 months ago it starting making a knocking noise when I applied the brakes. I thought it was my differential (it isn't) because it is a used transmission. That's not it. My mechanics were stumped, of course it never seems to make the noise when they have my car. They also checked the rotors, and I maintain my brakes.They replaced a wheel bearing on the left front wheel, the noise stopped for two weeks then started up again. Only when I use the brakes do I hear it, and I hear it more often than not.
There also seems to be a bit of a creaking noise with it. It does it more in stop and go traffic, and the car usually has to be a little warm before it gets noisy. They ended up replacing a rear drum thinking the noise transferred to the front, didn't work. What could this be? it's pretty loud and disconcerting when I'm driving. It only happens when I use the brake (more so slower speeds) so what is left besides the wheel and the brakes? My mechanic said the noise stopped when they replaced the wheel bearing because they took the wheels off, and that somehow fixed it temporarily.
View 7 Replies
I have a 2011CRV 2 wheel drive that is making a clunking noise in the front brakes every time I take my foot off of the pedal. I took it to the dealer twice and both times they told me that there is nothing they can do about it. They said it has to do with the way the pads wear but said that even when I change them the clunk probably won't go away. I have never heard a car do this.
View 4 Replies
I have had a clunk in the front end that started out as a light clunk that was sometimes noticeable. It has now turned into a clunk that can be heard very often. It sounds like a hollow clunk. I'll try to explain it so it makes sense...If I'm going over a bump or speed bump or something like that it doesn't really do it noticeably. If I'm driving a get to a place where the road is uneven or there is a hole or pothole and the front end seems to "fall into the hole", then the sound is very audible, and I can feel it slightly in the steering wheel and under my feet in the drivers floorboard. So, I've had the front end checked out 4 times and between what they said to do and what I've read on here...here is what I've done so far......
Changed end links with moog end links
Changed sway bar bushings with moog bushings
Undid the bushing mounts from the front frame and wired the sway bar up to keep from flopping around. No change in sounds
Didn't get rid of the clunk....
Had front end shop check out truck... They said ball joints were ok, no play in them. They did say that they could feel some "clicking in the pitman arm pivot" when turning the wheel. Like something was loose in box.
I've changed shocks and bearings.
I can grab a hold of the passenger outer tie rod at the adjustment sleeve and rotate the tir rod and it will rotate around in the socket and hitting on the insertion point and make a metal thud sound.
Again, took into shop and they said that would be normal b/c the tie rods have to have that to keep from binding up in front end.
My thinking is that if the tie rod rotates that much, then it is rotating the drag link which in turn puts stress on the pitman arm which in turn has either broken or sheared the pinion shaft inside the box and then when I go over a hole, it moves and all of the above is put into motion.
Shop (Ford) basically called me an idiot and that wouldn't be the cause.
So, now onto my thoughts and questions....
Radius arm bushings
Axle bushings (????? how many and where are they all located)
tie rods and drag links..
View 10 Replies
I just got my left front axle replaced on my Toyota (1993) and my engine mounts as well. The car is in great shape and has been driving well.Drove it away, and it was running great. It is still running great (after driving all the way home) but, I noticed it is making a loud clunking, metal on metal kind of noise on the front left axle when in first gear, happens more when turning (I think right, but maybe both right and left). I just paid a lot of money and trust the mechanic, but this does not sound right at all.
View 7 Replies
Alright I've got an 09 camry le on 18's, I recently just put the tein s tech springs on and since day one it clunks when I hit bumps. I did the install myself (not bad, just time consuming), so no taking it back to someone. I've taken the wheels off and made sure the bolts are all tight and the top mount too. Everything is snug. Still clunks. Is this just something that is normal with aftermarket springs on stock suspension?
View 14 Replies
I just bought my 2009 toyota avalon and i wanted to know if it was normal for a knocking noise when the car is on and idling. Car has 46k on it. What a normal idling avalon sounds like?
View 10 Replies
I have a 1995 Toyota Camry. I let my niece use it while on xmas break when I went to go pick it up it made a clunking screeching sound as i tried to back it out of the parking lot. I found it difficult to turn the wheel as well. I had to get it home so I drove from Orlando to St Augustine. Weird thing is that once on the highway going 70mph i didn't hear the sound anymore. I thought it was ok. I stopped in Daytona for gas and as i pulled away that sound began again. This lasted until i got to accelerated to about 50mph this time. I heard it again going through my neighborhood which is 25mph. It was very difficult to turn the wheel. My husband checked the power steering fluid which it was empty.
View 6 Replies
The '04 Camry with 72K miles is making a little of the clunking noise when the steering is hard-over to the right (have not tested left yet). My education on this site says it's the CV joint. So, how urgent is it to get this fixed? The car is getting used probably less than 8K miles/year.
View 4 Replies
