I have 35k on my 2009 camry, (past warranty). All of a sudden in the last few days when I make a sharp left turn (like into a parking spot) I hear a grinding noise from my car. Not really a full on grinding, but like a quiet fart can muffler noise. No issues with alignment, driving straight, or sharp right turns.
View 5 RepliesLately my 2007 Camry (2.4 L, Auto) has developed a bit strange problem. When I'm driving on highway, even slight left turn results in a grinding noise and sort of resistant steering wheel. It happens only when I turn left. As soon as steering wheel gets back to straight, the noise and steering wheel resistance/hardness goes away. I don't really feel much when I'm driving slow on the city streets. Although some time when I am little bit fast, I feel slight grinding noise and steering hardness. No problem in turning right at all.
View 5 RepliesI'm having 4WD problems with my Yukon, but the dealer keeps telling me there's nothing wrong with it (this has been going on for 2 winters now), which is either code for, "let's wait until it's extended warranty expires, so we don't have to pay for it," or "the computer says nothing is wrong, so that's all we're going to look at." When it's in 4WD, anytime I make a sharp turn or even turn a corner there's a grinding noise in the front, if I try to back up, it will only go as far as one revolution of the tires then stop (I have to take it out of 4WD to backup), eventually the "Service 4WD" light comes on, but apparently nothing gets recorded on the computer. It has 32,000 miles on it.
View 6 RepliesI have a 2013 Santa Fe with a 2.0T. A couple of days ago, I heard a squealing noise when I make a sharp turn to the left, like maybe a power steering belt would do. This has continued and I have also noticed that the AC fan almost completely dies at the same time. Car has 6,000 miles.
View 3 RepliesAt 120k miles, my 2003 Camry LE 2.4L started to make some noise when making sharp right turn at low speed (below 5mph) going forward. It sounds like the tire rubbing the fender or somewhere, not metallic, and it's periodic, at 2-3Hz or so. It comes from somewhere on the driver side but I'm not sure. The car doesn't make noise when turning at stop or backing up or going straight, and the noise seems to disappear if turning at higher speed (maybe the turn is not sharp enough).
First I suspect the tire is rubbing the fender. But after inspection, no rubbing marks can be found, and there seems no rubbing when the car is parked and the wheel turn all the way to the right. Then I suspect a bad CV axle. But the boots seem in good shape with no leaking grease, and there's no noise when backing up.
The other day I hit a good size bump at speed, slightly bent a wheel which I didn't even notice at first. The car drove straight and had no other symptoms, thought everything was okay. A couple days later I heard a weird grinding noise while making a left hand turn, it was so faint I honestly thought it was the fender liner. After the noises continued and further examination I noticed that the carrier is rubbing the rotor on the lower drivers side corner.
View 1 RepliesJust had a new issue pop up - sometimes, when making a sharp left turn when the engine RPM is low (going into driveway, turning at a stop sign), the engine will suddenly die. It seems to be running fine otherwise, it does not idle rough, and the idle RPM is around 600-700. It never dies on the highway or higher speeds, yet anyway.
I do notice that my power steering pump is making a little noise. It is an aftermarket pump. The steering assist seems to work fine though.
I recently had the spark plugs, valve cover gasket, and a fuel pressure sensor replaced. As I understand it, the mechanics checked the fuel pump and it was working fine.
We have an '07 wagon that recently started exhibiting the following: When doing a sharp turn left or right you can hear a rotational shhhhusshhhing sound... shussshhh *pause* shusshhh *pause*.. etc. Its obviously linked to the front wheels since going straight does not produce the sound. Brakes and rotors have 13k on them; dealer has checked out the car and says everything looks good and the bearings are fine.
Could this be CV joints or something similar? Where to look? This is not a thud thud thud (which I have heard before when another car of ours needed new cv joints). Safety is main concern, don't want bearings freezing while driving..
I recently acquired a B4000(for a steal!), had it almost a month now and im starting to notice a few problems, all driveline related (I think).
1. Have a "grinding/rubbing" noise in a LEFT turn only. It is a 4x4 and I haven't turned a bolt on it yet, save for very minor stuff. Since this particular model has some costly parts, I'm trying to prevent buying unnecessary parts! I have a set of 31 x 10.50 on it, and even though there is some minor tire rub, im 90% certain this is not the case.
2. Has a somewhat "hard" shift when going into O/D(I think), doesn't do this all the time, I wonder if problem #2 and #3 are related.
3. Appears to be about 1in slack in the rear driveline, wondering if it is the rearend, and specifically the spider gears or pinion?
4. Also seems to be just a LITTLE slack in the front left CV axel, is this something I should be worried about? the front right is good and tight, Tcase shifts like its suppose to.
When I make a left turn I have a horrible grinding noise. Only when I turn left and at any speed.
View 2 RepliesSo four lanes, divided, with a left turn lane, five lanes at the intersection. I'm down ~15 mph, maximum turn speed and one car is just clearing intersection and and +100 yards from next approaching slug of traffic. Keeping the speed, I make the left turn confident no problem then halfway through turn:
feels like a soft tuck
traction light flashes
already to straighten out
everything normal
This is the second time I've seen this in a year. Pavement dry, 48 hours since last rain; ~8:00 AM so rush hour is on. Before doing some parking lot tests, any clue about how to replicate?
My dashcam SD card did not play.
Every time we make a sharp right or left turn the engine on my van stalls. It has to be completely restarted. In the last year we replaced the trans and steering column and had a major tune-up. So far, no one has been able to diagnose the problem.
View 5 RepliesI have a 2006 with 106K miles. Noticed after making a sharp left turn in a parking lot that the Red Triangle came on along with a beep and the message, "Problem" on the touch screen. Started happening more frequently either when the wheel is turning left or if I'm driving straight and the car drifts a little towards the left if I'm on the highway. Today it happened about 6 times. Warning goes off after a couple of seconds.
View 9 RepliesI've had my R since late mid-summer, and one of the first things I noticed was this clunk sound when reversing into my parking spot and when making an aggressive sharp turn. Usually Left.
After reading multiple threads on this topic, I came to the conclusion that it was my sub-frame and the bolts need replacing. I got in a GB for the tyrol subframe stiffening kit after reading some good reviews/responses.
Today, on my day off, I finally went to a mechanic to get this installed. I just changed my mechanic, and this was my first visit to the guy hes had over 10 years experience at vw and just opened up his own shop. He did a great job, torqued the bolts to spec, made me drive around, do some pulls in 2nd and 3rd gear, reverse forward etc.
So hes about to pull the car back in to retorque and.... CLUNK...
Get in the car, reproduce the sound, get the car back up on the hoist... and at this point I'm expecting the worse. He takes my control arms off, checks the end links...
Brings the car down, and the clunking sound is louder than ever. It was the weathergaurd. When I turned on the wheel it was pulling it out and when I straightened the wheel it was popping it back into place, making a big clunk sound.
This was the exact sound that I was hearing, thinking it was my subframe. The bolts that came out were not stretched or bent out of shape like the ones you see in other reviews. They're actually in great shape. I'm glad I did the Tyrol kit and do not regret it, and I definitely feel a difference when I went into some aggressive turns.
My 2003 Camry makes a a grinding noise when the wheel is turned even slightly left. The noise is present at any speed, and is the same volume no matter what. I'm fairly certain its coming from the driver side front wheel. I changed that CV axle in January so hopefully that's not the issue.
View 2 RepliesMy 2005 Camry started to make a, for a better work, "grinding" noise that appears to come from the left front side. It seems to appear around 40mph. Other symptoms:- the noise is not present when the car is in park even when revving up the engine- the noise appears to be correlated to the car/wheel speed - if placing the shift in neutral, the noise does not change while the speed doesn't change- if starting in 2nd gear, the noise only appears around 40mph when the engine is about 4500rpm.
Here it is a little hard to distinguish as the engine masks it- if switching the the 3rd gear, the noise does not change- if switching to "D", the noise does not change- coasting at neutral at more than 40mph still gives out the noise- when going over higher spots in the road (when the load of the wheels is reduced) the noise intensity goes down
There is no (or very low) noise at low speeds. Also, no noise when taking sharp turns. Had both front wheel bearings changed and the break pads, and the noise did not go away. I will be taking the car to a transmission place soon.
My steering pulls hard left or hard right, and also seems to have a mind of its own when it turns sharp right or left suddenly, as though someone else is driving. It's very disconcerting when you think you're making a left and the truck veers right.
Today I was making a left onto a bridge and truck kept going straight. I almost hit the bridge. I have an 06 Ford F250 Turbo Diesel. What this could be?
I have noticed that when I turn my wheel on my Touareg, mostly sharp turn, I get a slipping/almost grinding noise. I am planning on driving cross country next week and this has me worried.
View 13 RepliesI have a 2009 Toyota Corolla and it's making a loud grinding metallic noise on the front left side. It does it while I drive the faster I go the louder it gets. When I turn to the left it makes it louder, when I turn right the noise decreases. PG&E have been breaking the roads by where I live and there's a lot of little rocks I drive thru. I'm wondering if that's the problem?? What do I do?
View 4 RepliesI have a 2013 Avalon hybrid that is almost 1 yr old.
I have recently notice a single "pop" noise that seems to be coming from the rear when I turn right with a sharp turn.
I have looked in the trunk and under the vehicle but I cannot find where it is coming from.
I have a 2003 f150 4X4. Whenever I go around a round about slowly, the truck sort of grind under the frame and shakes a little bit like I am in 4 wheel drive.
View 2 Replies