Camry :: 2007 Transmission Not Shifting Into Gear Properly
Sep 19, 2011
I have a 2007 Camry V6 XLE with a rebuilt transmission. Since the rebuild I have had an intermittent problem with the transmission not shifting into gear properly from park. When shifting from park into drive, sometimes the transmission will pause, leaving the vehicle in neutral, then slamming into drive.
The transmission was replaced in April of 09 with a leaking transmission seal. Since this time I have has this problem but have not been able to get it to be reproduced for Toyota to observe.
Purchased: February '08 (ish)- New
First Transmission Replacement- April '09- 35980 Miles
Transmission Repair- Internal Temp Sensor/leaking o-ring/Transmission Flush- 9/13/11- 101k miles
View 9 Replies
Advertisement
Took my car in for oil/filter change and in some odd circumstance, the young mechanic managed to drain 1 liter of transmission oil out of my car (which I didn't know at the time). After driving for 10 minutes (~5 km), I noticed my reverse gear wasn't shifting properly. After ~30 minutes of driving, my car was smoking from the exhaust pipe (turns out he had overfilled my engine oil too!!). Took the car back in to complain the mechanic supervisor claims my transmission is still fine and all I need to do is refill the lost fluid. Another independent mechanic later tells me my transmission line is likely fried if I had experienced what I did, and those guys should be responsible to replace everything. Since fluids have been topped up, I have no proof of who is right. So my question is, if I only drove for maximum 50 km after my transmission fluid was drained and engine oil overfilled, would that be enough to cause serious damage to the car?
View 10 Replies
I have a 94 Camry 2.2. When I am driving 45 MPH the transmissions acts like it is shifting into N or OD and then the RPMS fluctuate between idle and 1500 or so. Then when I it will shift hard because the car has decelerated. If I stay in the throttle during this it just jerks or lunges.
View 3 Replies
just bought a 2003 camry 4 cylinder with 126xxx miles automatic, everything seem fine when i was test driving and all. I bought the car and finally drove the car for around town running errands and all of a sudden i started to noticed a stutter in between shifting from 2nd to 3rd gear.
View 2 Replies
Just curious if there are any other 2010 owners with any difficulty shifting gears in their manual transmission camrys? I noticed during my test drive that I grinded my way into 2nd once... I thought it might have just been my nervousness with a new clutch at the time. However, I've since put 300 miles on the car and I still have trouble putting it into second gear on a daily basis. Sometimes it grinds a bit, and sometimes it catches or a half second before it pops in. All the gears OTHER than 2nd gear go in like butter as you would expect with a new transmission. I'm not new to a clutch... this is at least my 4th car with a stick, so I don't think I'm doing anything out of the ordinary when shifting.
It reminds me of some older (100,000+ mile Nissan) cars I've had in the past... the syncromesh was wearing out and it would grind going into second or third, so I put in some RedLine MTL and got a little more life out of the transmission... but there shouldn't be a need for that kind of thing on a car with less than 1000 miles on it?!
View 14 Replies
We have a 2010 Santa Fe AWD LTD with about 140, 000km on it. It recently came back from front suspension work. The suspension is fine now, but we notice harder shifts in the transmission. Also, there seems to be a vibration just before shifting gears and when under load (like going up hill) seems to slip (like on ice) about once every second until the shift is made. Once the shift is made it drive smoothly until put under pressure again. Even stepping down a bit on the accelerator will cause this slipping feeling (or maybe its loss of power). Just had new plugs put in and a tuneup so it's not that. Could something from the suspension work cause these symptoms?
View 29 Replies
Bought a 2007 es350 2 months ago and transmission shifted fine during test drives but now seems to hesitate when shifting from 2nd to 3rd gear when not warmed up. Also seems to not engage at low speeds of around 5mph again when cold. Seems to shift normally when warmed up or after the the first couple shifts of the morning. Is it a simple fix or a prelude of something worse to come? Other than that I love the car so far.
View 7 Replies
My 2007 V6 failed me several times on very cold mornings. I start the car, wait about 1 minute and then drove it to a stop sign or red light (still cold). When the light turned green, I tried to proceed, but it was as if the car was in neutral. The car would not move. It was only after about 2-3 minutes, when the car started to warm up that I was able to get a gear. After 5-7 minutes, it was as if nothing happened. I have 97K on the car.
View 6 Replies
My truck was noticeably sluggish when it shifted into overdrive or would refuse to shift into it all together, so I decided to change the filter and fluid in it. After this maintenance task was done, and I test drove it, I noticed the problem was still there. It also seems now that it has trouble shifting in all gears. When I tried to "manually" shift it through all gears, the transmission would hold it in the previous gear, buck, shake and then shift at a higher RPM.
Not only this, but if I floor the pedal, the truck doesn't want to drop to a lower gear to increase RPM. It only bucks and carries on until I let out of the gas. I also noticed that when I rev the engine in park, the engine does not want to go past 4,000 RPM, and I hear a "grinding" noise at about that range. In the past, I could red-line the engine in park/idle no problem. Does the auto trans have the ability to "hold back" the engine or do I have deeper engine problems?
View 17 Replies
Grand am is a 4cly 4speed trans. My daughter is off to school. She called and told me her speed odometer is not working. She also mentioned that it is not shifting properly if at all. Is the speed odometer operated by cable? Would the two be related to the transmission going bad?
View 4 Replies
I have a 2013 F-150 Lariat 5.0 L, 6 speed auto transmission crew cab truck with 44,000 miles on it. Recently I have experienced problems with the transmission not shifting properly. Three times when I have started out of my driveway, it has shifted into 2nd gear while I am going only 2-3 mph up my driveway which is about a 10-12 degree incline. It stays in 2nd gear even if I stop. When I pull out onto the highway, it shifted normally into the remaining gears. Then, the other night as I was returning home, while traveling up the road, it shifted into 5th gear and stayed there even when it needed to downshift. A wrench i-con appeared on my screen, my odometer showed dash lines instead of mileage and my seatbelt i-con appeared. When I got home, I shut the truck off and restarted it and everything was normal again. I have driven the truck a couple more times with no issues. The transmission shifts normally. Could a sensor be going bad ?
View 2 Replies
The car on cruise control sometimes randomly looses speed & downshifts to 3 and raise rpms quickly to gain the set cruise control speed again."
Vehicle Background: bought it from the original owner, the fuel gauge showed empty on a full tank of gas and I passed on the car, owner called a week later and said they installed a used PCM and everything now works, and it did, I bought it since it was a really clean car.
After driving on highway with cruise control set it would randomly loose power and downshift and then regain speed from being set on cruise control, mostly uphills and downhills but also straights sometimes and it would loose 7-8 mphs not the 1-3 mph loss that is typical of some other cars on cruise.
Engine has been rebuilt to success, other then this issue, the car drives like a dream and doesn't burn a drop of oil. Plenty of power compared to before the rebuild as well.
I learned from a DIY oil consumption fix on a 98 corolla that removing throttle body and cleaning it and the IACV, makes the vehicle idle within stock spec, really quiet and also improves the throttle response, I attempt this on the GT-S.
So I open up the airbox to make room to clean my throttle body and the 2 nuts were fairly loose, but the 2 bottom bolts were completely out that attach the throttle body to the intake manifold and only holding their place because of the tight fit in that area from all the hoses. This wasn't even touched during the engine rebuild.
I remove everything, looks dirty as [censored] and the intake has some oil in it, which I use brake parts cleaner to dry and use air to blow off and only got to remove maybe 30% of it from the inside of the intake. I then also remove the IACV to find it REALLY dirty like all the ones I had open so far and I go to town and cleaner both that and throttle body and replace both the gaskets as well.
Upon completion the vehicle's throttle response becomes AMAZING compared to before and it seem like a proper GT-S rather then a slow car which before had a slower acceleration then my 01 GT. I drive the same route home of 25 miles, the car NEVER once down shifts and has plenty of power and I'm HAPPY!
Well guess what, the issue is back now, I open the air box and both the nuts and the bolts seems firmly tight. I loosen everything up to still see the oil in the intake(though I only got to remove/dry30% the first time), brand new OEM PCV valve in the car 5k ago and I followed the PCV Valve pipe to the intake and it was dry from the inside as well.
when the vehicle is driven around and it returns to idle, it seems to hesitate(I think not 100% since it could be the engine just slowing down didn't do it before the throttle body cleaning though) for less then a second when going back to idle speed, it idles perfectly at around 750 rpms though. Questions:
1. What could be causing the oil in the intake? is it just the old oil what has been in the intake since before I bought it? The car doesn't burn any oil in the last 5k since the engine rebuild.
2. Could it be the PCM/VCM is causing the random power loss with cruise control on? which was a problem that was so called fixed using used parts but all the other automatic functions work perfectly.
3. Could it be the Cruise Control it self, apparently I can snag one from a local pick n pull for like 8 bucks (I think, listed on website)
4. Could it be this issue listed in this link? [URL] ..... , bad throttle position sensor? could it be that I cleaned the idle air control valve too roughly to get that slight hesitation when returning to idle?
5. Could it be the Throttle body itself in the GT-S? Did I clean it too aggressively, and ruined the round opening, which is causing the random loss of power? I had my cuzin do the throttle body removal and cleaning DIY step by step on our 99 corolla and he used a gasket remover (attached to a power tool) to clean up the dirt/oil build up inside the round opening and it started to give him jerks driving at highway speeds, constantly...We used the 98 corolla's gently cleaned throttle body in the 99 corolla and immediately issue solved. The proper working throttle body in the 98 corolla is a used replacement one as I aggressively cleaned the round opening in the original one and had hesitation issues as well.
View 4 Replies
In my 2011 F-250, 6.7, auto....it seems that at certain times went the tranny shifts from 2nd to 3rd and I pause with acceleration, for some reason the tranny seems to go into a slip mode and then slams into 3rd. Now I read about 8 months ago that there was a computer upgrade via Ford. Which they did when I was having some work done on the truck at the dealership.
View 14 Replies
I recently purchased a used 2001 E350 with a 7.3L and the transmission is not shifting properly. It will go into Reverse no problem, put it in "D" and it starts in high gear and will not shift out. If I manually shift from 1 to 2 to "D" it works fine and will even go into OD. It will not down shift on its own either. What should I do to fix this issue?
View 2 Replies
My 2003 Dodge Dakota does not shift properly sometimes going into second gear and it only happens in second gear. I have to lift my foot off the accelerator for it to shift into third. If I don't it just screams at a high RPM and sounds as if it is about to blow. It has a hard time making it up a small incline such as an off ramp. Truck will not shift properly when going up grade. Engine will rev at 4500-5000 rpm but will not shift until I slightly release the gas pedal. Truck will also perform multiple hard up shifts whether in cruise control or not in cruise control, going upgrade. Took the truck to the dealer reprogrammed the computer with a "flash update" that was no luck. Not once has the ENGINE LIGHT ever come on.
So a lot of the comments that were presented to me I have done. Here is a list:
Changed govner senors and solenoid. Did not work.
Checked for exhaust leaks and other leaks. No leaks.
Checked all vaccuums. No problems there.
Had engine checked and dyno tested. No problems there.
Had transmission rebuilt. Same problem. (dealer did work)
Had new transmission put in. Same problem. (dealer did work)
Also, sometimes when I put the truck in reverse, it seems to about to stall, but it doesn't. It also does it sometimes when I put the truck in drive it seems that it wants to stall.
I just recently learned that my truck has a Transmission computer module, Transfer case computer module and of course the main computer. Is there a way to test those modules out?
View 3 Replies
My 2006 Elantra (54,000 miles) shifts really, really hard when it's not cold and passes through the 35 mph range -- hard enough to make you glad you've got your seatbelt on. I've taken it to my regular mechanic and now it's in an automatic transmission shop.
My mechanic changed the fluid (twice), and took it through a "learning sequence". The fluid didn't look that bad and he reported that there were no codes to work with. He thinks I'm going to have to get a new transmission.
The AT shop has confirmed that there are no codes to work with and that the problem begins at 143 degrees. They tell me that the transmission is shifting into a higher gear without releasing the lower gear. They tried replacing a couple of solenoids, but that yielded no change in behavior. Now, they're telling me they "think" I need a new computer. I'm just afraid the trial & error approach is going to cost me a boat-load.
View 1 Replies
I have a 2000 F150 5.4L with 157k miles on it. I think it has the 4r70w trans. The transmission has started holding 2nd gear too long before shifting into third. Throttle position doesn't matter, it does it even under light throttle. I do not have a check engine light. I have owned the truck since new and the trans fluid has been changed 3 or 4 times. The fluid looks pretty good now, not burnt or anything. The truck has been sitting in the garage a lot over the past 2 years, I drive it at least once a month and have put maybe 2000 miles on it this year. It shifts fine through the other gears, just 2-3 has an issue. Truck has the towing package.
View 6 Replies
I just bought a 2007 Santa Fe 3.3ltr with auto trans and all wheel drive. When I purchased it the speedometer did not work. I bought the VSS gear and installed it and now my transmission does not shift properly. Also I had it to the dealership for an ECU update and they said that their computer could not connect to the ECU.
View 2 Replies
My transmission is not shifting into 3rd gear this is a 350 turbo hydramatic.
View 12 Replies
Have a 2000 expedition with 84,000 miles. Tranny seems to shift hard from first to second gear. Its been 24,000 miles since my last dealer tranny service. Thinking of getting a new service now before the recommended 30,000 manual recommendation. Whats happening?
View 6 Replies
This morning while driving on the freeway, the the transmission stopped shifting into 6th gear. This was at 70 mph. The only way it would shift up to 6th is by using the manual mode, however after manually shifting to 6th I moved the stick back over and it immediately downshifted to 5th at 70+ mph. Concerned, I pulled off and turned the engine off. After i restarted the engine, I continued to my destination and the trans shifted up to 6th on its own. The car has never done this.
View 3 Replies
