Camry :: 2007 - Brake Rotor Rubbing On Caliper Bracket
Jul 4, 2013
I'm working on a 2007 Camry and I had the wheel bearings pressed in & out at a shop. I put everything back together but the driver side rotor is rubbing against the caliper bracket. And there is no air gap between the rotor and bracket so it can spin freely without rubbing. The passenger side is fine, there is a little air gap so the rotor can move freely without rubbing. I don't understand why the driver side rotor is rubbing against the caliper? I checked everything over, the pads and rotor are the correct ones. I also took the pass side caliper bracket and installed it on the driver side and same thing, the rotor still rubs against the bracket.
View 13 Replies
Advertisement
1999 F350 4x4 dually. Replacing brakes front and back. Rotors, Pads, and hoses. On the left front put rotor back on and torqued down hub nuts on rotor. Then caliper mounting bracket wouldn't fit back between mounting bracket and rotor. Loosened the hub nuts on rotor, and fit mounting bracket in place. Then torqued down the hub nuts again, and rotor rubs on mounting bracket and rotor/hub won't turn.
View 2 Replies
I replaced my warped front brake rotors a couple thousand miles ago and all was fine but when I went to swap over to my snow tires, I can see that the outer part of the rotor has been rubbing on the caliper bracket. This is happening on both front rotors. Could my new rotors be too thick or something?
View 4 Replies
I pulled a brake caliper off for inspection, and when I reinstalled it, I managed to strip one of the holes on the caliper bracket when putting one of the 7mm bolts back in - haste makes waste, ya? So, I am trying to find out my options, is it possible to get it re-threaded, helicoiled, or is it toast and I need to buy a new one?
View 2 Replies
I read a reference to the front brake caliper bracket bolts being one time use torque to yield and must be replaced every time they are loosened. Is this true?
This is on my 06 F-350 in my Sig.
View 3 Replies
3 weeks after having my brakes replaced. At 60 mph yesterday.
The garage has the car now and is saying it was a freak accident and not something they caused. I call foul to that. It's a 2007 Subaru Outback.
What should I say to them to make sure this gets repaired properly? And what unseen damage should I be looking out for? The wheel run has a groove from where the bolt rubbed. That's all I could see. And I could lift up and wiggle the caliper.
It was only the pad replaced on the front brakes. It was pads and rotors on the back.
View 12 Replies
I read a reference to the front brake caliper bracket bolts being one time use torque to yield and must be replaced every time they are loosened. Is this true?
This is on my 06 F-350 in my Sig.
View 11 Replies
I am trying to remove the rear rotor of a 2007 Camry, but it appears to be stuck on the parking brake. The parking brake is not engaged, but the pads are firmly pressed against the rotor (rotor was loosen from hub assembly using bolts through the two threaded holes).
I have removed the rubber plug and attempted to turn the star adjuster, but it doesn't seem to move in either direction. Also, the adjuster should rotate away from you to tighten the brake and toward you to loosen, correct?
View 13 Replies
2011 Lexus RX350 ... What are the Torque specs for the caliper bracket bolts (front and rear caliper brackets) a pdf will be great
View 1 Replies
The caliper/bracket has worn down on the front brakes to the point that I am replacing pads couple of times a year and they vibrate excessively when braking hard like on a hill. on other year years, these parts are separate and bolted together, on the 95 it is one welded piece . I cant seem to find a replacement part, even when trying to order the entire wheel hub assembly it doesn't show/specify if that part is attached. I did find replacements at a junk yard but they too were worn. Is it possible to convert to another year wheel hub assembly?
View 4 Replies
Last Spring, my 2007 Camry Hybrid (54k miles back then, now at 62k) developed an obnoxious squeal coming out of the left rear wheel while driving at highway speeds. It takes several minutes at this speed to make the sound, so I believe wheel temperature triggers the sound. Touching the brake would temporarily silence it. After parking the car, I discovered that the left rear wheel was very warm, while the others were cool. I also saw excessive brake dust on the wheel.
I pulled the wheel to inspect. and saw that the track of the brake pad had moved a millimeter or two up the disk, so now part of the pad was over the "rusty" portion of the disk. The rusty, unworn part of the disc was thicker, so the part of the pad that was now over it was rubbing. At higher speeds, the rubbing would heat up the wheel and I'd gradually get the loud squeal.
I dismantled the pad, cleaned it, tightened the mounting brackets (via slight bending) and put it all back together. This solved the problem for 8 months. It just came back to haunt me on a recent highway trip...
It's a pain to take it all apart, especially if I am only temporarily fixing the issue. The pads still have over 85% live (including the rubbing one) and the disks look great on all wheels with no vibrations.
View 7 Replies
I'm having a tough time separating the brass fitting, even using a 10mm wrench. I noticed it moves below the bracket, so I'm trying to hold the oval with square corner base on the hose itself, but even then, have started to round the corners on the brass nut.
I'm gonna continue with the job, leaving the old hose, and will have to come back to this later, because I'm installing a new caliper (old one froze, and I just found out why, broken lower slide).
Any trick to separating the fitting between steel brake line and rubber?
ETA, to replace the brass fitting, does it mean cutting the tube, inserting another fitting, and flaring the end? I hate to leave the old hose or a rounded nut.
View 8 Replies
I haven't had luck trying to find the torque specs for the caliper bolts on my 2010 ES350. What are the correct numbers? a pdf diagram would be very useful.
View 1 Replies
2005 Toyota Solara my front driver side caliper was sticking and heating up a couple months ago... replaced the caliper and the rotor... still had the same problem. I would drive it, it got hot and stuck, after I parked for a little while it slowly released. Talked to a couple of mechanics and they both said undoubtedly I had a bad flex hose and it was collapsing with pressure and then will release... I changed the flex hose and flushed the fluid and it was immediately fixed...no problems.
Drove the car for a month, went to South Carolina and back and then a couple days ago the same thing started happening. Talked to a mechanic, he told me that the new caliper may have gotten fried from over heating before I changed the flex hose... Got a new caliper today (warranty) exchange... changed it out and still have the same problem. When it sticks I can release the pressure by opening the bleeder valve so it seems like the flex hose issue again... my only thought now is maybe the new flex hose is a bad one and someone mentioned the proportioning valve.
View 9 Replies
I put brand new pads on my 2003 sc430 about 6 months ago, and have noticed this rubbing sound coming from all 4 tires. It is very noticeable and annoying. I'm wondering if I should have put brand new rotors on the car while I was changing the pads. I did not here this noise prior to changing the pads.
I'm attaching a link of a video [URL] .....
View 14 Replies
So, my right, rear, brake caliper froze in the open position a little while back; I hit the brake hard, it held, heard a clack, then it let go and stayed in the open (uncompressed) position. I lost some braking power but at least have been able to drive. No visible brake fluid leak, other three brakes working fine.
At 125K, I've decided to do a full brake job, and am about to search for some of the parts on the awesome stickied parts reference list up above. I'll hopefully find some parts are available at NAPA, where I'm also ordering the right side cv axle.
So, I'm only finding remanufactured brake calipers at NAPA. Are they decent or should I look for something new elsewhere?
View 14 Replies
Every time I am pressing the brake pedal, I hear a distinct clicking sound coming from passenger front Brake Caliper Area.
I have applied brake grease (green) to the pad shim.
I have replaced the spring sets on each front caliper.
Passenger Brake Clicking Lexus LS460L - YouTube
View 8 Replies
The wife and I ventured out last Friday evening to run a few errands. When we returned to the house and pulled into the garage, we both smelled burning brake pad. I felt the rear wheels, the drivers side was too hot to touch.
Dragging brake caliper. I got online and reserved a drivers side caliper and a set of pads at NAPA. Saturday morning I removed the caliper. Much to my surprise, one of the caliper pistons was broken into multiple pieces.
I took the offending caliper to NAPA and picked up the new caliper and a set of pads.
Side note - NAPA seems to think the 2007 trucks have calipers that mount in front of the axle, not behind the axle. They will try to sell you a passenger side caliper and tell you it is a driver side caliper. It will bolt up fine, but the bleeder valve will be at the bottom of the caliper instead of the top. You'll never get the air out of the caliper.
Got back home, bolted up the new caliper and pads, then bled the system. All worked well.
I decided to throw new pads on the passenger side brakes as well, since I had 2 remaining. I took off the passenger side caliper, much to my surprise I found a cracked and broken piston on that side also! Another run to NAPA to pick up another caliper. Installed, bled the system again, all working well.
Now, I have never seen a cracked and broken caliper piston like this, let alone one on each side of the rear axle. What might have caused this? About a year ago I had a shop install new backing plates. The pads and calipers are about 3 years old, same shop installed those.
View 7 Replies
I recently replaced my pads and rotors. The driver side was no problem, but on the passenger side, when I was finished, the caliper was rubbing up against the rim of the tire. I took both tires off to compare the differences, I noticed that my passenger side caliper is not going down as deep on the pads as the driver side. The caliper on the passenger side depressed with no problems and had no problems fitting over the pads. Whats really confusing is that all of my bolt holes line up.
View 11 Replies
My car is pulling to one right slightly so I did the alignment. But it didnt eliminate the problem. Ｉ jacked up my car and try to rotate the front wheel. I can hear slight noise of the caliper rubbing the disk and the wheel does not spin freely if I stopped rotating it. However, the noise is subtle so I don't know if it is by design or I have a brake drag.
View 7 Replies
I'm in the process of changing pads and rotors on all 4 wheels. I've done all brakes and rotors, except that I'm stuck on the driver rear. The driver rear rotor won't come off!
Here's what I've done so far: I've used the metric jack bolts (I didn't buy the long ones) and that freed up some rust, with pb blaster. Now, the rotor comes out a bit, and I'm able to move it around, and the rotor comes forward a little bit towards me. It's so wobblily that it seems like it is about to come out. The rotor isn't solid stuck on, like most threads I've read.
While hammering, I think a piece of hardware of the parking brake fell down on the ground. Do u think that the parking brake is not allowing the rotor to come off? If so, I was reading online that there is some way to release the parking brake via a hole though the rotor, but I'm really not familiar with this. I'm not even sure if it's the parking brake that's not allowing the rotor to come off.
View 14 Replies
