Camry :: 2006 LE ABS No Stability Control / Brake Pedal Goes To Floor
Jul 4, 2012
2006 Camry LE 4cyl ABS no stability control, rear drum brakes. The brakes stop the car, but the pedal does go to the floor and it doesn't brake with confidence.
Prior to the repairs everything looked normal (aside from one wheel cylinder, see pic) and there was no leakage. The fluid was at the proper level though dirty.
I replaced the master cylinder and did a complete fluid flush and bleed. I also changed the front pads (it was time anyway) and the passenger side brake hose. I was going to to both hoses, but I wound up snapping the steel line on the PS and spent most of the day dealing with that. I decided not to press my luck with the DS.
I might change the DS hose, since I already bought it. At this point the only thing left is a weak caliper or wheel cylinder seal, or a bad hose (though I don't see any visible bulging when brakes are applied).
My wife was driving on the freeway last week and she applied brakes but they barely stopped the car and the brake light came on. She was able to limp it home without incident but the brake light stayed on and the car was braking poorly. The next day I inspected everything and found no leaks, and the fluid was not low but it was dirty. I drove the car and noticed braking performance was lacking (though it was never great to begin with) but I never saw a brake light. The brake light isn't on at this point.
View 14 Replies
Advertisement
Evertime I turn left the brake light, traction control and stability control lights come on and the car starts dinging. Mechanic says it could be front wheel bearings because they are tied to the ABS system??? But I have been seeing alot about wheel speed sensors?
Second, everytime I brake suddenly, a cloud of smoke comes from the front end and there is a burning oil smell. The oil is fine and no leaks. Again mechanic says it could be a cracked CV boot throwing grease?
Lastly everytime I put in reverse or when I lightly put pressure on the brakes when driving I get this noise like a humming (errrrrrr) noise. Its not the grinding/squealing noise you would get when brake pads needs replaced. I only have 60k miles on this.
View 30 Replies
My 04 Camry is having brake issues. It has 205k miles. The front pads are great and the back shoes are great. (Drums in back) I've had them adjusted multiple times but my pedal still goes almost to the floor. It's not the master cylinder cause I've already replaced that. The pedal doesn't bleed off either. But I have bled the brake lines and there is no air left in the lines.
View 14 Replies
My mother went out 2 days ago to go run errands, she stepped on the brake pedal and it went to the floor (car still in garage and in park, low mileage car 81,xxx garage kept). I have not been able to duplicate the issue. The fluid has been changed twice since new, no signs of fluid loss, undercarriage inspection revealed nothing. I am thinking maybe a vacuum hose issue.
View 2 Replies
A friend brought me a car with the issue that the brake pedal sinks to the floor when braking. She said it was never low on fluid so I replaced the master cylinder and bled all of the lines with a friend pumping the pedal. The pedal would still sink to the floor. I tried vacuum bleeding the brakes and found that the front left consistently had large bubbles.
I Teflon taped the fitting on the calliper and the bleed screw which improved the problem but didn't fix it. I then replaced the calliper. The front left calliper still won't bleed and the brake pedal still goes to the floor. When I bleed it the regular way, the fluid comes out of the bleeder like it bled nicely. Neither of the rubber hoses that connect to the calliper have any visible damage. I had a friend pump the brakes while looking at the hoses and their is no bulge or swelling in them. Could the ABS need to be bled?
View 4 Replies
When I press the brake pedal, the car will stop. But if I keep pressing it while the car is stopped, the pedal wants to keep going towards the floor. I have to press hard for it to do this. I have bled the brakes. I've checked the calipers and the hoses for leaks and don't see anything. The master cylinder is topped up and I don't see any fluid underneath it. It doesn't appear to be leaking. The funny thing is, when I turn the engine off and press the pedal, the pedal comes to a stop and doesn't want to move after I pressed on it as hard as I can.
View 2 Replies
I have a 2007 Sonata GLS 4cyl. Anyhow lately my brake pedal is going right to the floor. The brakes seem to work fine, but if I keep constant pressure on the pedal it will slowly go all the way to the floor. My rear rotors and pads have been changed a couple of months ago and I'm pretty sure my front brakes are good. What could be causing this? I also checked underneath the car for leaks and there doesn't seem to be anything leaking underneath.
View 6 Replies
My brake pedal went right to the floor yesterday. I knew my rear brake was squealing so assumed it was my pads worn out. I went and bought pads. Fronts were half gone, rear was all gone. I couldn't get the rear tire off the back passenger(I even loosened lug nuts and drove up and down street) so only 3 replaced for now. Second time in a row rear brakes wore out well before the fronts.. Well, while that tire(I tighted it up again) soaked in pbblaster I drove it around for the day. Lost brakes again. After a few pumps I gained pressure. In the driveway I pumped and pumped and pumped the brakes.
Eventually I did see the leak all over the driveway. Of course it's on the tire I can't get off. So I checked the brake fluid. It was down but still visible. Closed hood. Then came back to car an hour later and now hood won't open. I had my wife pull the lever inside the car and you can hear it moving under the hood but I can't pop the hood up in order to get my hand under there to release the lever. Is there a trick to open the hood manually? My old dodge stealth had a small hole you could get to with a long screwdriver to open the hood manually. I thought most cars have a trick like that that isn't well published so people can't break into the hood. Does the camry have one? Now what?
View 1 Replies
I got in the car (2010 Prius IV, 170k miles) this a.m and the brake, ABS, & stability/traction control lights all just lit-up. Can run & drives just fine.
View 19 Replies
So I took the pads off and saw pistons that push caliper against rotor were to far out to install new pads. (rear pads were still intact, both front pads were out when i pumped) So im pumped the brakes thinking it would reset them and alls it did was push the fronts out more.. I noticed fluid leaked out of the pistons after fully pushing them out.
After seeing that pushing the pedal only pushed them out and didn't reset them, i pryed them in with a C wrench. Was quite difficult but managed to do it. Note I only did this on the front pads..
Rear was just fine, piston went back in easily. I filled brake fluid fully and still does it - Now pedal hits the floor when i first hit it and seems very light when braking.
View 12 Replies
I was driving around today and had to hit the brakes really hard for the first time. ABS kicked in and during the ABS 'action' the brake pedal rapidly went to the floor. With each 'pump' the ABS made it felt like the pedal sunk slightly.
This was on dry pavement, a little gravelly / dirty and the car stopped rapidly, but just as I stopped the pedal was VERY close to the floor, and with just a touch more pressure it did in fact hit bottom.
Sounds to me like the ABS pump needs to be bled, is that right? Can I do that myself with a VAGCOM? I hate having the dealer do anything, even if it is their job. How to SAFELY confirm if cars does / does not do this as well?
View 8 Replies
2005 Volvo S60 T5, 90,000 miles. The brake pedal depresses almost to the floor. Dealer service has not had a solution to this problem. All brake components are supposedly nominal. Might pedal position sensor be faulty?
View 1 Replies
When I go to start and depress the brake pedal it goes all the way to the floor. The brake fluid is at the full mark and my 2011 has only 25k miles. Where should I look since it did not go all the way to the floor when I forst got it with 6K miles.
View 19 Replies
I drive a 1991 F-150 Lariat Extended Cab. Out of the blue, my brakes decided they didn't want to work unless the pedal is about 1/2 - 3/4 of the way down to the floor. As soon as I release past that 1/2 mark, they shut off. While this makes it great for tailgaters, it does not make it great for police officers.
We have already replaced the switch thinking maybe it was that, but alas it was not. I was reading in a couple difference places about the multiswitch? However, the symptoms other people had were similar, but not the same. I never tilt my steering wheel, so I dont know if that's the issue!
View 2 Replies
2013 Prius c Two, bought brand new with 15 miles on it 5 weeks ago. A few times when driving, I noticed the brakes seemed weak, like they weren't stopping the car very well even at low speeds (My driving is mostly in town on residential streets, so I'm rarely going over 35 MPH. Even so, I'd have to really mash the pedal all the way to the floor to get the car to come to a complete stop, otherwise it would keep moving forward. Several times I ended up about 5-10 feet past the line, sticking the front bumper into cross traffic. Luckily no one hit me. I chalked it up to the quirks of a different car than the one I was used to, and figured if it kept happening I'd take it to the dealership.
On Monday, my wife was stopped at a red light. The light turned green and the car in front of her started to move forward. After a few hundred feet, he suddenly slammed on his brakes. She said her brake pedal went all the way to the floor, and the Prius didn't slow down at all. She hit him going about 25-30 MPH and totaled the Prius. She's an excellent driver and I've been with her before when she's had to panic-stop. She's never driven a car without ABS, so she is used to pushing the pedal hard and keeping her foot on it. She wouldn't even know how to "pump" the pedal. She swears the pedal just went all the way to the floor and the car didn't slow down at all.
View 18 Replies
For the past several weeks, my daughter reports that she has to put her foot almost all the way to the floor to get the brakes to work. The brakes do not have an effect until her foot is 1-2 inches from the floor. It usually happens after she has been driving for a while without pressing the brakes. I’ve driven the car numerous times but haven’t been able to replicate the problem. Her commute is approximately 10 miles each way in stop and go traffic. The car is a Volvo xc70 with 200k+ miles. I've had it looked at by a mechanic who didn't find anything but it's continuing to happen. I'm suspicious that it may be a master cylinder problem and concerned about complete brake failure -- should I be?
View 7 Replies
I have been working on my 01 Elantra for 2 days now. My problem is that I have absolutely no brake pedal at all, it just goes right to the floor. and this is only when the car is running, when it is off I give it a quick pump and i have a nice firm pedal. I installed a new master cylinder, bench bled it and all that jazz. I replaced the rear brakes and a wheel cylinder, I have also bled the brakes multiple times, and mutliple ways. bled the master while on the car and all the brakes while the car is off and while it is running. I dont know what else could be wrong with this. I looked at all the lines and there are no wet spots, no hoses are swelling up. everything looks top notch...i just have no brakes why.
View 15 Replies
My Sienna 2005 experience intermittent complete brake failure 3 times within 18,000 miles,the brake pedal goes to the floor and it does not slow down, so I coast until I stop. However, when I release the brake pedal and then reapply the brakes, it works fine. A non-Toyota mechanic thinks it's due to malfunction of ABS. The dealership is unable to finds error codes and brakes work fine when the Sienna is in their hands. I scared that the brakes will not work the next time I reapply the brakes.
View 30 Replies
I have a 99 Blazer 4x4 with ABS. Brake pedal just went to the floor and car stopped eventually ... a bit scary. I've checked all the brake lines and the inside of all wheels and there is no sign of fluid anywhere. All pistons seem to be where they need to be with backing plates nicely visible.
I pumped the brakes quite a few times and same result ... but I'm not pumping fluid on the ground. As expected I've also checked the reservoir and its full. Didn't see any leaks so its full. I'm guessing that the master cylinder has given up the ghost ... truck has 470,000km so things wear out.
View 5 Replies
I have a 96 voyager, it has been a great car for the last 10 years I've had it. My brake pedal goes down to the floor, it gives brake but I think barely and my brake light comes on. I have Bled it twice and changed the master cylinder , neither worked, I'm perplexed, my mechanic thinks it is the abs.
View 3 Replies
My B6 purchased exactly three weeks ago has had a soft brake pedal since day one. By "soft," I mean that when parked with the engine running and applying moderate pedal pressure, the brake pedal provides some resistance but sinks to the floor. If I pump it up a few times, it temporarily gets much firmer, but eventually sinks to the floor again after a few seconds. Now the car so far has never failed to actually stop, and it can get into the ABS. But during an abrupt (okay...panic) stop last week, it did go to the floor while the car was still moving. That's when I decided that was enough and took it back to be serviced.
My expectation was that there was just a small amount of air in a line somewhere, and that they could bleed the system and fix it. That was my experience with my B5: it was very sensitive to the least little bit of air, and if it wasn't thoroughly bled after brake service the pedal often got mushy and could find the floor. But bleeding them always get the pedal back to normal. So the service advisor said that he "had the service manager drive [my car] and compare it to a new Passat [on the lot] and talked to "Quality Tech. Manager to confirm." And the confirmation was that my brake system is "working as designed." In short, they say the brakes are working properly and there is nothing to fix. So I have now picked up the car and it still does the same thing.
Now I can (and will) bleed the brakes on my own over the weekend. But I would like feedback from others as to whether or not their brake pedals regularly see the floor. I just can't see this being the way any hydraulic brake system should work..
View 21 Replies
