My 2006 Camry V6 had the code P0420 before. I replaced 2 downstream O2. Now it throws code P0136. What should the next step I am looking for here? Is it a CAT issue?
If I need to replace CAT, do they have custom (modify) CAT to improve the performance?
My 2006 Camry V6 had the code P0420 before. I replaced 2 downstream O2. Now it throws code P0136. What should the next step I am looking for here? Is it a CAT issue? If I need to replace CAT, do they have custom (modify) CAT to improve the performance?
View 5 RepliesMy 1999 Camry - 4 cyc has a trouble code of P0136. Auto Zone told me it is a defective bank 1 sensor 2. As per the repair manual, the front passenger seat has to be removed to get to the sensor's electrical connector but an internet video shows that the driver seat has to be removed. Replacing the heated bank 1 sensor 2 on a Camry before?
View 9 Replies2002 F-150 4x4 super crew w/5.4..So I've got the P0136 code, horrible fuel mileage (around 7 mpg just driving to work without hitting very many lights) and the check engine light comes on intermittently, and I get that code. I have borrowed my friends scanner ("Determionator Scan System") and I can see the live data from the 02 sensors. Today I drove around for a while and watched the scanner and the H02 data, and the downstream sensor on bank 1 shows at most, .09 volts, and it also says its detecting a lean mixture. The code P0136 is for this sensor in particular, and I have heard that an 02 sensor should be around 1 volt. The downstream sensor on the drivers side showed around .75 volts at max.
I believe that it is working correctly, or close to it, and I do not get a code for that sensor. So my question is, is the downstream sensor on the passenger side (bank 1) causing the P0136 code and the poor fuel mileage? also, could an exhaust leak cause the sensor to throw a code and not be bad at all? I do have some very minor exhaust leaks, on both sides of the truck..I'm leaning towards replacing that one 02 sensor. The wires and plug connection to that sensor look fine, plus I would think that if there was a bad wire/connection it would not register any voltage at all.. I have to add, the truck runs fine overall after I replaced the intake manifolds last week. It does still idle high, around 1,000 rpm, after coasting to a stop, then after a few seconds goes back down to a normal idle of around 650 rpm. but idles normal upon starting or in park.
I recently replaced both the downstream O2 Sensors in my 2000 4.2L F150 because I was getting a P0136 (Bank1 Sensor 2) code that I couldn't get rid of by cleaning the connector or fixing wires. 110K miles. Calif truck. No other codes and has always passed smog test easily.
When I pulled the sensors, the Driver's side unit was extremely sooty, as compared to the passenger side (bank 1). The code failure was on bank 1.
Is this normal or is there some rich condition on the driver's side bank that I need to check into ? Originals were Bosch, replaced w/ Motorcraft, if that makes any diff. One on left is driver's side unit.
2004 XLT 3.0L 141K
I just bought the truck on Monday, the CEL popped up on Tues. It shows code 0136. No other codes. CAT "not ready" on scan tool
A google search proved this is a common topic that for some owners is a repeating and cronic sort of issue. What I've read online is that there is an assortment of things that can cause this O2 sensor to throw this code:
Actual bad O2 sensor
Faulty wiring or connection
Misfire throwing mix off
bad convertor
I don't believe this list covers all the accounts I read but these I have were definitely repeat offenders. My intention is to take to a dealer and let them have first crack at sorting it out. I'm handy enough but I see this as something where an unseen detail can drive ya crazy.
2006 Toyota Camry 4 Cyl Manual Transmission. I'm getting a PO017 code - Engine Coolant Temperature (ECT) Circuit Low Input.
The dashboard temp gauge reaches a red H at low speeds. After about 15 minutes of driving, the car overheats and shuts down when the car slows down. I wasn't at home and didn't have coolant, so I put water in the coolant reservoir. 15 minutes later at home, the car overheated and shut down. The water in the reservoir was boiling and steaming.
When the car is idle, the radiator fan turns on immediately. I noticed the passenger side fan doesn't run. Could the one fan be the problem?
I was also really low on oil and added oil. There's oil on the engine block too. I might have multiple problems at the same time. See pics. [URL] .....
I have a 2003 F150 V6 4.2L, 171,000 miles on it. I have four codes on it.
#p1518
#p0316
#p0303
#p0136
I had a p1518 in november of 2012, had it repaired and its back. In the time that I had it repaired and it came back on (maybe a month and a half ago) I only drove the truck maybe 3000 miles, if that. Just curious if this particular part should have some kind of warranty either by the MFG or dealer since the dealer repaired it. Have a limited budget, trying to find out what I can fix on my own in a timely manner.
Symptoms:
-Car "Surges" at any speed. Loss of power is significant.
-Check engine light is on , DTC code = P0420
Tried:
-Fuel injector cleaner
-Spark plugs replaced around 40k miles ago
-Checked for leaking valve cover gasket (oil in plug wells) None
Can a clogged fuel filter cause this? At idle the car is fine, the symptoms seem to only occur when car is under load (In drive). My son drove this car an it always seemed empty meaning he never put much gas in it.
This issue pertains to a 2006 Camry LE 4-cyl.
My check engine light came on - code P0032 (upstream O2 sensor). I bought a new sensor from O'Reilly Auto Parts. After installing the new sensor, the car would jerk while accelerating. This continued to happen until roughly 30 miles or so when the engine light came back on and the jerking stopped! I re-scanned the car and it showed the same error - P0032. I then erased the code, and the jerking issue resumed.
I assumed this was caused by a faulty O2 sensor. I returned and got another one. Same issue.
Is this the result of not getting an OEM sensor from the dealer? Or is there something else I should be worried about?
I have a 07 Sonata V6 that misses only when warmed up, runs fine when cold. code p0301 for cylinder one misfire, I have replaced the plug, coil and injector for cylinder one and still the same. idles and runs perfect when cold, dead miss on number one cylinder when warmed up.
View 1 RepliesI get this code, p171, every so often on my corolla. I have cleaned the MAF and finally changed it with one bought at AutoZone. I still get the code. What should I do next?
View 4 RepliesCheck engine like on my 03 Camry with 2.4L is own & got an OBD code of P0031. Just bought the car with 38k miles one owner & can't pass local emissions.
View 10 RepliesI recently had a CEL code for bank 2 cat converter.. I drove the car with the CEL for 8 months and one day the VSC and TRAC OFF light popped on and wouldn't go away. I took it to toyota and they told me that it is because the check engine light is on and once the CEL goes off the others should as well. Well i recently replaced the bank 2 cat and cleared the CEL and iv driven over 300 miles already the CEL has not come back on but the VSC and TRAC OFF light remain ON....
View 2 RepliesI have a 98 camry 4 cyl and am continually getting egr code po401. I've cleaned out and tested egr, replaced modulator and the vac switching valve. Replaced several hoses also. Car runs fine, in fact this code came the day after traveling 700 miles. It comes back on fairly quickly after properly resetting computer and 1 or 2 drives.
View 3 RepliesI recently purchase camry 09 and when I did the computer for the car it returns me P0012 and C0205 errors. I have searched for P0012 error and got an idea to check the oil control valve. but for C0205, what exactly I have to check for?
View 2 RepliesMy 2009 Camry came down with the p0157 code which I looked up & is oxygen sensor circuit, low voltage bank 2 sensor 2. I'm trying to figure out which side this is(driver or passenger)? Also have a p0430 code-catalyst system efficiency below threshold.
View 2 RepliesThe check engine lamp on my '04 4cyl came on Saturday. I checked the code. It's P0441, which is supposed to be 'Evaporative emission control system incorrect purge.' I found a page on the web that said this might have to do with the gas cap. When I checked the cap it had not been tightened.
I've been driving it for 3 days and the check engine lamp is still on. How long should I expect it to take for it to extinguish? It seems unlikely to the point of incredible the gas cap was left loose (which I've never seen before) and another failure in this very system could have happened simultaneously. Particularly since this is the first time the check engine lamp has come on in 9 years and over 100,000 miles
I have a 4 cyl 02 camry LE. Recently the CEL came on and a few minutes later the oil light. after a day or so they went away. When it happened, I immediately went to the auto parts store and they checked the engine codes and got only one the P1349 repeated several times.
About 6 months ago my water pump leaked and that was replaced along with the timing belt. Shortly after that I had the oil changed and they over filled it i found out. I changed the oil and that was fine. i did develop a slight oil leak from the top passenger side of the engine though. so far i don't notice my oil level dropping. I just see some oil spray in that area. I mention this as they seem related to the code.
The code relates to Possible causes
- Dirty or low engine oil
- Valve timing
- Oil control valve
- Variable Valve Timing controller assembly
- Engine Control Module (ECM)
My friend has a 07 Camry 4cyl and has code P0606, Engine control module/Powertrain control module processor. The car runs and drives good. My friend recently got the piston rings replaced about a month ago for the recall, and he told me the service light was not on when he dropped off the vehicle. After he got it back it wasn't on and just came on a few days ago. Hard to believe the ECM is bad on the car, I'm thinking it was something with the removal and install of the engine causing P0606. Does it need to be reflashed?
View 1 RepliesMy CEL came on and is throwing code P0430. Is it just an o2 sensor? if so which one primary or secondary?
View 2 Replies