Camry :: 2006 - Check Engine Light Came On - Code P0032 For Upstream O2 Sensor
May 4, 2014
This issue pertains to a 2006 Camry LE 4-cyl.
My check engine light came on - code P0032 (upstream O2 sensor). I bought a new sensor from O'Reilly Auto Parts. After installing the new sensor, the car would jerk while accelerating. This continued to happen until roughly 30 miles or so when the engine light came back on and the jerking stopped! I re-scanned the car and it showed the same error - P0032. I then erased the code, and the jerking issue resumed.
I assumed this was caused by a faulty O2 sensor. I returned and got another one. Same issue.
Is this the result of not getting an OEM sensor from the dealer? Or is there something else I should be worried about?
View 4 Replies
Advertisement
Car: Camry 2004 xle 2.4 L .
My problem: based on P0032 code I replaced both O2 sensors (before and after catalytic converter) ..
Am still getting engine light on and code P0032.
View 6 Replies
I just bought an 04 camry 4 cylinder. It was running perfect when I got it but the moment we got home it threw a CEL. The code was for an upstream o2 sensor, however I did a resistance test and the heater circuit is fine. I did a voltage test on the blue and white wires and I got 3.3v and 2.9v. I don't remember which wire gave me which voltage at the moment. I would like to know if this data is a good thing or if it's broken. I do not have any data to go off of, and I couldn't find the factory service manual online. Its also worth mentioning that it idles very rough and the catalytic converter is giving a rotten egg smell but not all the time. When neither of these things happen the CEL goes away. I do not want to start throwing parts at it.
View 1 Replies
My 2005 Camry check engine light is on. The trouble code is P0138, bank 1 sensor 2 oxygen sensor. Engine is the 2AF-ZE. Not a California emission car. Car is Japan built. It has two O2 sensors. What is the correct OEM part #? I believe it would be a Denso?
View 2 Replies
I have a 2001 Exrursion 5.4L V8. The code P1131 comes up and it says "Lack of upstream heated oxygen sensor switch - sensor indicates lean - bank #1". I hear it could be the sensor that is bad or there is a vacuum leak. It runs like a champ, no spitting, no sputtering, no missing, no ruff idle. What do I need to do to fix it or where do I need to start looking?
View 3 Replies
I just bought a '98 Ranger 2.5l 2wd. After driving it for a week or so I got a P1405 Code. After a quick google search I got :
P1405 Ford - DPFE Sensor Circuit Upstream Hose
Possible Causes: - Faulty Differential Pressure Feedback Electronic (DPFE) sensor (EGR pressure sensor)
- Plugged or damaged EGR tube
- Differential Pressure Feedback Electronic (DPFE) sensor harness is open or shorted
- Differential Pressure Feedback Electronic (DPFE) sensor circuit poor electrical connection
Now, I have done my research between forums and youtube and have found this EGR system to be quite. I've gone ahead and replaced my DPEF. I took an air hose and blew out all the small lines coming into the DPEF. I still have the engine light. My next move is to get a volt meter and see if I'm getting power to the sensor.
My question is about this particular code and is it possible I need to look farther into this EGR system (EGR Valve, EGR Hose, etc.)
View 5 Replies
I just purchased a 2006 GS300 AWD w/115k. Started car on lunch hour to find check engine / check VSC lights on. Ran codes to find P0333 Knock Sensor code. Vehicle seem to run perfectly fine, but now that the light is on, it is definity spark knocking under acceleration. This is my first Lexus / Toyota product, so I am unfamiliar with the common problems or fixes. Are knock sensor replacements common?
View 6 Replies
2004 XC90 T6. Local Volvo dealer (Bangkok at the time) said my check engine light was due to the O2 sensors going bad. I changed out the one under the car, then my wife threw out (accident) the other so I didn't change the one accessible from the hood. The check engine light went away so I figured that was that.
Fast forward a year later, I buy an Autel Maxiscan MS509 and now I'm getting check engine code P0455 which is probably the O2 sensors I didn't replace. Other than deductive reasoning, is there some way to look at the data on my OBD reader to confirm which O2 sensor is bad?
View 4 Replies
I have a 2008 Camry Hybrid and recently got a "Check VSC System" warning light. A diagnostic resulted in a C0210 error code. The code is for a right rear speed sensor malfunction.
I had a local shop look at it and he replaced the hub accembly including the speed sensor. It didnt work. He and I took a ride and on his diagnostic tool, the speed reading for the right rear wheel was all over the place.
The next day he replaced it thinking that the new sensor was bad. This worked, however only for a day. Now the light had come on again with the same error.
View 2 Replies
I have a 2012 hyundai accent. The check engine light came on. The code read knock sensor. Before I could get it into a shop, it went off. It didn't come back for 11 months. When it did come back, the same code was read. Again, it went off the following day before it could be looked at and hasn't been seen since. The shop says that even though there is a history code, it would be hard to diagnose since it isn't an active code. I noticed absolutely no difference in performance when the code was active. Both times it went on, the car was idling for several minutes with the ac on, and it came on as i accelerated onto a highway immediately afterwards. However, it has idled like that many other times without the light coming on as well.
View 11 Replies
I've been having an issue with my car and the check engine light is on.
The code reads : P0030
Heated oxygen sensor - bank 1 sensor 1
heater control circuit
2001 VW GTI VR6 ....
View 4 Replies
So, I have my check engine light and the code is p0327 (knock sensor). Clear cose but it returns. Going on for 3 days now. I was suspicious that something else is going on. I also remembered I've been using a little more antifreeze in the reservoir. So, today I needed to watch the coolant. I ran the car for an hr and I found a lot. Red coolant on my belt, the back passenger side of my engine and it was caked on with coolant. I think the water pump is going up.
I was concerned that coolant was also leaking from the intake manifold but it's only the right side, so I'm pretty sure the coolant is being slung around from the belt. I rinsed the engine down and the knock sensor code went away. Temporarily, until more coolant got back there. Do you think I will need to replace the knock sensor along with the water pump or should the sensor work ok after some intense cleaning after the water pump replacement?
View 5 Replies
My 2009 Camry check engine light is on. Dealer said the two O2 sensor both are dead and need to replace. After dealer reset the check engine light I have driven two days for 50 miles and the check engine light doesn't come back. If the O2 sensor is bad how long does it take for check engine light on again? Is it possible the check engine report on by mistake since two O2 sensors got bad at the exact same time is really rare.
View 13 Replies
Wife has a 08 solara 2.4 auto. Check engine light is on for bad knock sensor in bank 1. Now car is not pulling itself, it takes off fine then shifts and falls on its face, I think its missing 2nd and going to 3rd. It is also not shifting into 5th so its staying in 4th and using a lot of gas. I tried manually shifting but it still goes to 3rd and will not go to 5th. I have been told this knock sensor could be causing it all. Cant clear code, I hit clear but nothing happens. We don't have a lot of money to pay the Toyota dealer to fix it and I can do all the work but they wont even show me where the knock sensor is.
View 5 Replies
I have a 2002 Jetta 1.8t. My check engine light came on and it gave me the code P0135 sensor heater circuit. Bank 1 Sensor 1. We bought a new 02 sensor and replaced it. We definitely bought the right one too. Cleared the codes. After a little driving the CEL came back on with the same code P0135. What is wrong and how I can fix this?
View 6 Replies
I own a 2000 Toyota Camry that was given to me by my father. The check engine light illuminated last year so I brought the car in to my mechanic. He said it was the o2 sensor and changed it. That lasted about a month , and the light went on again. This time it had to do with some valves that get stuck open (or closed) but also had to do with the amount of oxygen that goes into the carburetor . I asked my Dad if he had this problem, and he told me that the engine light was illuminated often, that he had brought the car in about 6 times, but nothing was found. Previously I owned a 1998 Camry, and had the same problem; the check engine light illuminates, the diagnosis is the oxygen sensor, that gets changed, the light goes on again, this valve thing gets changed but the light goes on again in a month. I can't get the car inspected with the engine light illuminated. The light always goes back on but nothing else is found wrong with the vehicle. I really know nothing about cars.
View 4 Replies
A few days ago my "Check VSC" warning came on along with the check engine and traction lights being on. I left my car in a parking garage for a week when I was on vacation and the lights came on once I started the car after getting back from my trip.
I have had the "Check VSC" warning before and I fixed it by replacing my gas cap. My gas cap seems fine this time around so I got my codes scanned and the only one that came up was P0300. Having this issue with the 2007 Lexus GS 350? I still feel like it's my gas cap because I bought a cheap replacement last time around.
View 8 Replies
I cleaned my k&n air filter on my 02 passat 1.8 turbo let it dry oiled it very lightly, and 50 miles later I get a check engine light on, pulled the code 16486 and it says Mass or Volume Air Flow Circ Low Input. Cleared the code put a frame in until I can get it filter. Why that would throw me that code, k&n oil gumming up my sensor??
View 2 Replies
1996 Ford Explorer on a small island with no mechanics. Vehicle does less than 100 miles per year, never over 20 mph. The check engine light came on and the code reader says it's a problem with the Camshaft Position Sensor. The vehicle runs fine, just as it did before the check engine light came on. I'm tempted to put some electrical tape over the check engine light and keep driving.
View 2 Replies
My '03 Tacoma Prerunner V6 has 116K miles and recently lit up its Check Engine light, returning a code for a failed up-stream air/fuel sensor. I recently drove across country, using many different fuel formulations ranging from CA gas to midwest ethanol to whatever they put in the gas here in the NY-NJ area (a mystery ingredient that seems to turn motorists irate and confuse their horn as a turn signal.)Anyway- age, or fuel, what killed the sensor? If fuel, will it happen again by time I get back west?
View 2 Replies
Just over 6000 miles....Yesterday morning the light came on. Dealer wouldn't look at it for a week. Went to my mechanic this morning to check the code it was p0181 fuel temp sensor. I read something online about the block heater making it too warm. The other night it was cold so I plugged it in, then yesterday morning it got warm overnight like into the lower 40s. I noticed the grill felt warm too. My mechanic cleared it if it comes back on do I have an issue? Is it ok to drive?
View 14 Replies
