Camry :: 2005 XLE - Grinding / Thumping Sound From Front Passenger Wheel
Dec 25, 2013
I have a 2005 Camry XLE. Since past few months I have started hearing a strange grinding / thumping noise from the front passenger side wheel. It can be clearly heard at slow speed and almost sounds like the wheel is lopsided and is rubbing against something. As the car picks up speed, the frequency picks up and the sounds disappears eventually.
So, I figured it must have been because the car had hit a curb few months ago and must have bent the rim. I had the wheels looked at while getting rotation and balancing done and was told that there is no rim damage. The sound went down a little after rotating the wheels but is still there. The mechanic doesn't think that it is the bearing because the sound disappears after moderate speeds. So, trying to figure out what could be causing the noise?
View 14 Replies
Advertisement
2004 Sienna LE with 193,500 miles. While driving home tonight I started hearing a grinding noise from the passenger front wheel. The noise goes away on acceleration and braking. Whenever I take my foot off the gas it starts to make the noise again. It sounds almost like a brake noise but I just replaced the caliper bracket this past weekend and the brakes look great (less than 20,000 miles on caliper, rotor and pads). I suspect a bearing may be going bad and want to know if these symptoms match a bad bearing. The wheel bearings are all original.
View 4 Replies
I have a 2005 Jeep Wrangler Sport with a six-speed manual trans and an in-line 4.0 6-cyl engine. I discovered a month or so ago a strange rattling sound coming from, what sounded like, the front passenger wheel area. It would occur when I slowed down to 10mph or slower or when coming to a complete stop, or when starting out from a stop, until surpassing the 10-12mph mark. The rattle is audible both inside and outside the vehicle. It's a low-pitched sound like an "aaaaaahhhh" you make when opening wide for the doctor to look down your throat, only with a metallic rattle thrown in. Best way I know to describe it is a voice saying "aaaaahhhhh" through the back of a fan.
I recently discovered, when I took it in for an oil change and tire rotation, that my front tires were wearing much faster than the backs and had a very noticeable "choppiness" to the tread. I have since installed new shock absorbers on both sides of the front suspension in hopes that would even the ride out for the front and eliminate the choppy tire wear. I originally thought that the tire wear and the rattle were related, but I took it to a mechanic who raised the front end and hand-spun both front tires and they made no audible sounds while spinning.
The mechanic said he believes that the rattle is coming from the front differential. Now, I am no pro mechanic, but I am not afraid to tackle a car repair job as long as I know I have the tools I need at hand to properly complete the job. First of all, does the differential sound like a good place to look? There's no change in the rattle when applying or releasing the clutch and it shifts smoothly, so I am pretty certain it's not in the transmission. Is the differential something that I could remove the cover and adequately diagnose a problem on my own? Just don't have funds available for a large car repair bill, so I am looking at trying to tackle the issue myself.
View 1 Replies
I replaced both 1/2 axles last week after one CV boot pretty much disintegrated. Since it is a 2005 Acura TL with 146K miles, I changed both axles completely. BTW - I had NO forewarning, noises, etc. before the axles died last week! I only perceived an increase in road noise, but did not hear noises squeaks, thumps, clacks, etc.!) The first day I drove the car after the new axles, I noticed a thump, thump, thump from the right wheel area when I made a sharp, slow turn out of my driveway. It only happened once, but it was a quick trip.
The next day, I noticed it again as I pulled out of my driveway and later as I pulled into a parking spot. There are no other symptoms and it only occurs when the wheel is turned to an extreme (80-90 degree) at little to no speed. I tested it in an empty parking lot - slow circles in either direction will cause the thump, primarily coming from the right wheel area. I immediately drove to the repair shop and made an appointment. Why I'd develop a new thump immediately after getting new axles? I'm thinking something isn't right with their installation. Of course, they say nothing is wrong with what they did - the problem now is that I need stabilizer links?! Sounds like BS to me - why all of a sudden do I need BOTH stabilizer links immediately after repair work?
View 15 Replies
My friend has a 2005 Subaru Impreza RS (2.5 L) that just (today) started making what amounts to a clicking or thumping sound once the car reaches about 30 mph. I'm sure it does it at slower speeds, but I was unable to hear it. It is definitely in the front end. And seems to be coming from the drivers side. I asked if she had hit any large potholes recently, and the answer was no. Around three weeks ago she had studded snow tired mounted on the car. I don't think the tires are the issue. But perhaps the installation process may have played a part since the care was placed on a lift.
View 8 Replies
Just installed new actuator and wheel hub assembly on my 2009 f150,truck still had grinding noise in front passenger wheel , New solenoid and vacuum hose kit installed when test drove noise still there until you put the truck in 4 wheel drive it disappears . The noise returns as soon as you take it out of 4 wheel drive. Also mechanic said steering was tight,installed new shaft same thing, could this be the rack and pinion.
View 5 Replies
The passenger window is making a grinding sound when going down. Sound starts after the window is about 50% down. There is no sound when the window goes up. From what I have been reading, it could be a motor going bad. There is no damage to the glass.
Does this sound like the motor will fail? I have a 100K extended warranty on the car which is soon going to run out. The warranty states that it covers the part but only in failure. Does this count as failure? Seems to be a bit of a gray area since the part is failing but the it is still funtional...
Will be taking the car to Toyota but wanted to get hear some thoughts before I did that.
View 1 Replies
I've got a 2010 3rd generation Prius II with about 38k miles. Earlier today when I was driving around town the car suddenly started making a sort of grinding sound, metal-on-metal sound.
To cut to the chase, I think I've narrowed it down to something in the front right wheel. When I got home I put the car in park and had someone rev the engine. The sound didn't manifest, so I think this rules out the engine, belts, etc.. It doesn't seem to appear until the car gets moving. Almost right away, even at low speeds, the sound crops up.
I had someone drive the car very slowly down the street as I walked around the car to try to pinpoint the location of the sound, and I'm fairly certain it's coming from the front right wheel. It's present even when driving straight, so it's not strictly related to turning, although it is audible when turning as well.
View 6 Replies
I recently brought my 2005 toyota corolla to my mechanic to give my car a check up as i will be going on a three week road trip soon.Upon assessment, my mechanic told me that my front right wheel bearing was making a strange noise and that i should replace it. I went ahead and had it replaced. after i had it replaced the front right wheel area was still making a grinding noise (louder than before it was replaced). I brought it back and he replaced it again with a new wheel bearing.
Again after the 2nd replacement it continued to make a load crunching, grinding noise when ever i brake the car. So once again, i brought it back. I thought perhaps it was my brake rotor and had him check that. He did just that and said the break was fine. He said it may be because the axl was not sitting true. so i had the axl replaced. well today i picked up the car and drove it approx 5 miles and the same crunching/grinding noise persists!!! I brought it back and it is once again being worked on. I need it fixed and am worried that my car won't hold up for my upcoming 4000mile road trip. I have attached a video clip of the sound to this post.
View 16 Replies
My 2015 Gs 350 F sport started making grinding noise from the front passanger side wheel. The noise comes from driving and not braking so im assuming its not the brake pads and its not squeaking noises as a worn out brake will sound.
View 14 Replies
A little less than a month ago my wife's old 1999 Mustang had the tires replaced. Since that time there she has noticed two new sounds:The first is whirling/grinding sound coming from the front right wheel that comes and goes. The second is a low, loud groan that seems to come from the front of the vehicle when the brakes are applied. The groan varies in intensity but seems to always be present when the brakes are applied. The groan is not unfamiliar to anyone that's driven an older car, but it is much louder than I have ever seen on any other car (on the other hand I usually drive a Corolla so it may be normal on a V6 Mustang ).
The first sound seems to have been reduced but not eliminated since I followed the advice in this video below and pushed the plate behind the wheel back a bit with a screwdriver. Now it is only audible when the engine is off and the wheel is spun (in other words, when it is sitting on a jack and the wheel is spun by hand), but it is still there.
I took it into the shop where the tires were purchased and mounted. The good people at the shop did rotate and balance them, but both noises remain.
I looked at the calipers and discs and everything seems in order except (possibly) two things. The discs have rust around the edges not unlike the ones in this photo below and I have no clue if that is normal or a problem. The rust is present on all wheels and only the one makes that noise, so I think that may not be the source of the sound,. On the calipers some substance (paint?) is peeling off, but otherwise they look fine and again the same is true on all the wheels so it seems that is unrelated to the noise. I have not been able to get a look at the pad, so I don't know what condition they are in.
Other information: The serpentine belt was replaced a few days after the new tires were installed. The radiator was flushed at the same as the belt was changed. They also threw in an oil change and all the fluids checked at the same time. The tires are new Michelin Defender size 205 /65 R15 and all 4 tires are new. The engine is a V6 and the transmission is automatic.
[URL] .....
View 2 Replies
I owned a 99 f250 a little while ago. Just bought a 2006 crewcab F150 xlt about 2 months ago, and for the past month there has been this unusual grinding or whirring like noise coming from the front passenger side wheel.
I took it to the mechanic and he found a bad wheel bearing on drivers side and replaced it but that wasn't the issue. He could hear the noise but wasn't able to figure out what the actual issue was.
The noise only happens when my foot is on the throttle. (not when coasting) and i also just discovered that it doesn't make any noise at all when put in 4x4.
View 4 Replies
I just recently bought a 2000 Explorer, 4.0 OHV, 4x4 with about 150,000 miles.
I've had the vehicle for about a month, and ever since I bought it, it's had a grinding sound (sounded like wheel bearing) coming from the front right side. I replaced both right and left bearing/hub assemblies, and took it out for a drive. The initial sound that I thought was bearing noise is still there, and at about 65mph I started to get a little bit of steering wheel shake. I took my foot off the gas and it stopped. I accelerated up to about 70mph and it seemed ok.
I hit a VERY small bump in the road and the steering wheel started shaking like hell. So bad that I almost lost control. I slammed the brakes and the shake stopped instantly. I took it home and put it up in the air, half expecting to see something loose or broken, and everything looks perfect. I re-torqued everything that I had taken apart for the initial hub/bearing replacement, and took it out again. Same issues.
I never had ANY of these problems before I replaced the hub/bearing assemblies, so I'm completely confused. I was thinking CV joints, but I have no clicking at all when turning, in forward or reverse, everything is smooth. Outer tie rods were done about 6 weeks ago..
View 1 Replies
Early this week my car started making a loud knocking/rubbing sound (Kind of in between when your brakes are ground down to the rotor and a knocking pattern).
FIRST, it started only when I turned slightly left or left.... NOW, it's doing it as I go straight and when I turn to the right as well... oddly enough it's not as bad when going left anymore...
What this could be?? And if it's an easy DIY fix..... (maybe a link on how) and how much the part(s) might be?? I've taken video (for sound as I drive)...but not sure if I can upload it (size limit).
View 12 Replies
In February 2014 I purchased a 2011 Honda CRV. I often travel and am gone for about a week. Every time I come back the rear brake are rusted. They have a loud thumping and grinding sound. I immediately took the car back to Honda dealership (2 time) both times they 'shaved' the roaters. I then contacted Honda headquarters to report the issue. They told me to deal with the dealership and take it to a local mechanic for other opinions. Car Talk will be my second opinion. Honda dealership told me that this is just the way it is. This is my third Honda, I have NOT had this problem before.
View 8 Replies
I get a rhythmic thumping sound from my right front wheel when braking. The sound gets slower as the car slows, and when very slow sounds more like a grind than a thump. I can feel the vibration through the brake pedal. I've had this problem before, and had my wheel bearings replaced -- fixed the problem, but after about a year the sound came back. Just had the car inspected and brakes are in good shape (at least those parts checked out by the state inspection). Could it just be that I need to get the wheel assembly tightened up? (It's a '99 Honda Civic with about 145K on it, if that matters)....
View 11 Replies
So, last week I got my transmission replaced and they also had to replace the CV axle because it was damaged beyond repair when the Transmission self-distructed. They drove it after all the repairs and said it was driving fine, just that it had a belt squeak.
On my way home (30 min drive) about 10 minutes in, still in the city, my brakes start making a grinding noise and sort of a thump thump thump when I brake which sounds like its coming from the passenger side front, it makes me really nervous. It doesn't sound like any brake grindy noise Ive ever heard before and it wasn't making any brake noises before it broke down. (On a side note: it also made a weird noise maybe the first 3 times I drove it after getting it back and I turned the wheel hard to back out of a parking space, that used to be when I heard the belt squeak but I haven't made it squeak since I got the car back.)
Everyone I talked to said it sounded like it needed new pads so tonight I bought new brake pads and rotors for the front and got everything taken apart. The rotors didn't look bad at all, just some light surface scratches, nothing deep, no warping I could see, and the brake pads look almost brand new. I did notice that the inside brake pad on the passenger side was missing its little metal plate that is usually between the caliper and the pad, so I went ahead and replaced all of the brake pads hoping this lost metal plate was the issue.
I also turned the rotor by hand on each side while the brake pads were off and the only difference I could notice was when turning the passenger side one it made a little more noise almost like it was loose.
I got everything put back together and drove around the neighborhood with my boyfriend in the car to listen, the grinding noise was gone and it seemed to brake really well (never got above 30 mph.) However, on my way to return the rotors to advanced auto (45-50 mph) it started making the thump thump thump noise but without the grinding, still on the passenger side. I can feel it in the gas pedal and now it not only happens when I'm braking, but also any time I let my foot off the gas pedal. The only time I dont feel/hear it is when I'm accelerating.
View 3 Replies
My 2005 Camry started to make a, for a better work, "grinding" noise that appears to come from the left front side. It seems to appear around 40mph. Other symptoms:- the noise is not present when the car is in park even when revving up the engine- the noise appears to be correlated to the car/wheel speed - if placing the shift in neutral, the noise does not change while the speed doesn't change- if starting in 2nd gear, the noise only appears around 40mph when the engine is about 4500rpm.
Here it is a little hard to distinguish as the engine masks it- if switching the the 3rd gear, the noise does not change- if switching to "D", the noise does not change- coasting at neutral at more than 40mph still gives out the noise- when going over higher spots in the road (when the load of the wheels is reduced) the noise intensity goes down
There is no (or very low) noise at low speeds. Also, no noise when taking sharp turns. Had both front wheel bearings changed and the break pads, and the noise did not go away. I will be taking the car to a transmission place soon.
View 6 Replies
I noticed while driving my car there was a unusual rumble or grinding sound coming from my drivers side front wheel well. I get out and look I see a bunch of Fluid all over my wheel well. I look around turn my wheel around and see this fluids all on my rotors and suspension. Ive noticed couple weeks back the boots on the struts were ripped in two pieces from deteriorating or dry rotting (this was on both sides) and ive also been hearing some odd squeaking sound for over 15k miles every once in a while going over big bumps or train tracks. Struts go out at only 80k miles on their corolla? Yeah struts do usually lose their life around 60-80k miles but I've never seen them leak around that many miles. Is this a common issue?
View 5 Replies
I have 1999 F350 7.3 Crew Cab 4WD. I took it on a 4 hours trip towing a trailer to haul a small tractor on it. after 3 hours of driving, I started hearing grinding and metal chewing sound coming from the front axle or close the wheel hubs. It was awful, terrible, ... you name it!!! I had to continue or I will lose the tractor I paid for already. The sound was coming for 1-2 seconds each 500 feet or so. It never stopped or changed. I pulled over to see what's going on and found the following:
1. Left shock is leaking badly
2. Right locking hub is gone (not sure if the truck had one before). I bought this truck last year, but I never had to use 4x4 and I know the 4x4 motor by the transfer case is missing and the nipple on the transfer case is set to the 2wd position so the front drive-shaft does not turn.
I took the front shock off and continued to drive without it, the noise did not go away.
I pulled over again and this time I noticed that the dust cover on each end of the front axle is missing too. I have never worked on these axles before, but I jacked one side, and sure enough, gear oil was leaking from the other side. I took the plug off the front differential and stuck my finger in it. I felt a creamy brown-greenish stuff in the differential. The consistency is like mayonnaise or thin peanut butter. I put the plug back on and went to pick up the tractor because I did not want to miss it fooling around with the truck on the highway.
The truck made it there and back (almost 5 hours total after the break down). The sound never stopped every 500 to 1000 ft.
After getting home safely, I took the other locking hub off, and took it for a test drive. I did not hear the noise, but now my right brakes are locking.
I took of the wheels and saw that the retaining snap ring (C clip) for the front axle on the right side came off by hand. I took the washers behind it off. Took the calipers and brackets off. I have never done front axle rebuild. I am not sure what has been damaged and what's still good.
Right of the bat, I know, at least, I need 2 shocks, one brake caliper and pads.
My questions are:
1. Is it possible to take the front axles off on both sides and make it 2wd for now until I have the money to rebuild the axle?
2. Could I use the same hubs? or they are most likely damaged and how to tell?
3. How to tell if the differential is damaged/needs rebuilding?
4. How to tell if the axles/spindles are damaged?
5. Is there a step by step tutorial to rebuild the axle with all seals, bearings, ...etc? How hard is the job for a hobbyist? I do most of my repairs myself, and I was lucky at 36 years old, I never had to rebuild a differential.
6. What else I might have damaged in the process of driving it that long with the noise? How do I tell if I did?
View 8 Replies
I was under my car the other day and i noticed this dent in the rear of the subframe, just in front of the passenger side rear wheel. I didn't see damage anywhere else. Is this something I should be concerned about?
View 3 Replies
