Camry :: 2005 - L/F Caliper Are Locking Up
May 31, 2010
I'm in need of what's going on with my 2005 Toyota Camry 2.4L (American Build), Non-skid, on the front brakes.
About 2 months ago my L/F brakes just locked up. So, I towed it to the dealership to have the brakes looked at and worked on. They said my Camry was locking up because the L/F caliper is freezing up. So, what the dealership did is replace the 2 front rotors, new brake pads, and new calipers. Got the brake fluid flushed out, also. Now, after about a thousand miles later and about 2 months, the same thing is happening. The L/F caliper are locking up.
I brought it back to the dealership and they said NOW, that it's the "ABS Actuator Pump Assembly" and the parts/labor would cost roughly $ 1300 dollars.. Now, when they replaced that part. The same problem is still happening. The L/F caliper is locking up. Luckily, when it was locking up I didn't drive the vehicle to far to damage the brand new brakes that was put in the first place.
View 14 Replies
Advertisement
Someone had worked on the car and front caliper pins got mixed up. Where the pin with the rubber piece goes into. The top or bottom of the caliper. and is it the same for both sides.
View 2 Replies
My buddy has been having a strange problem with his 275,000 mile 2003 F150 2wd. The right side caliper will lock up out of the blue and will not release for anything. We put 3 news calipers on it within a 4 week period thinking that we had a defective one but no change. I am thinking either a bad brake line or, more likely, the front abs block...
View 1 Replies
I have a 1999 F150 Supercab, 2wd. I just replaced the front rotors, calipers, and pads. Before I did this, the front right caliper was locking up completely. Now, after the new stuff is installed, the truck pulls very hard to the left when braking. The harder you brake, the harder it pulls left. What should I look at next?
View 2 Replies
I was uber excited to buy my first brand new truck in 09..... Amount numerous issues, defective rear window (fought with ford for 3 years never replaced under warranty), sync issues draining my battery, multiple O2 sensors replaced, multiple lights replaced and a blown drive shaft all under warranty. Now my warranty literally just ended, years not miles, just rolled 36k yesterday, ran out 3 years in November 12, now I'm having break issues.
A few weeks ago while driving, I released the gas and truck seem to slow faster than normal. Seemed kind of unusual but also began to noticed a drag on my mpg, about 2-4 mpg difference, depending on highway or in town. Now 3 weeks later, I feel grinding under breaking. Now it's beginning to make sense. I figure probably a stuck caliper. While driving with head out the window , freezing in IL, by the way, seems to be the drivers front. Checked rotors, outsides only as there are the guards preventing me from checking the back side. No visual or touch grooves ground into the rotors from the pads being worn out. Best bet is its the back side of the caliper that is locked.
Question 1, does this make sense, only one side of the caliper locking up? I had a caliper lock on my old GTP but the whole thing locked up.
Question 2, do I just suck it up and replace the breaks my self, gf's dad is a manager at O'rylies so I can get anything I want at cost, or do I go back to the dealer and bitch about mechanical problems being constant with my new now only weeks out of warranty truck? I read some horror stories about clogged lines and numerous other issues causing calipers to lock. I don't feel like replacing my whole break system, lines, calipers and all just to make sure the problem is fixed. At 3 years this seems ludicrous.
View 4 Replies
I have been having problems on and off with my central locking for a while now with my 05' Toyota Camry Altise. 95% of the time it works perfectly, however occasionally the central locking will refuse to lock the doors, chirping at me twice as if a door is open. I know that all of the door switches are working fine so this isn't the cause of the problem.
I believe it may have something to do with the fact that I had to replace my driver side door a while ago, and that now the actuator may not be working properly or misaligned and jamming. What should I be looking for to make sure this doesn't occur? I thought it all went back in perfectly. Interestingly I can get around the problem by turning the ignition on and off and trying again.
View 6 Replies
I have a 2000 f250 4x4 with 4 wheel abs. The front passenger side caliper keeps locking up while I'm driving and won't release and when I hit the brakes it pulls hard to the drivers side. I have put two calipers on the passengers side and put new brake lines on.
View 8 Replies
I've run into a problem while doing brakes on my friends 2005 Sebring. I can't seem to get the brake caliper off. There is a little rubber boot with a plastic cap that is where the bolts that hold the calipers in place are. How to get the bolts out to remove the caliper. In fact, it doesn't seem like there are any traditional bolt heads in the plastic cover.
View 2 Replies
My 2012 Avalon developed a slight rattle at 9000 miles that continued to get worse. I took off the right front wheel today and found the top caliper bolt partially loosened. I could turn it with my FINGERS! The other one was tight as were the ones on the left side.
To diagnose this rattle, find a bumpy road that makes it rattle. Put your foot lightly on the brake (to load the caliper). If the noise goes away, it is probably a loose caliper bolt.
View 1 Replies
I have an 05 with a seized front caliper. What other vehicle has the same one? Does 4 runner or any other Toyotas have the same caliper?
View 5 Replies
Last Spring, my 2007 Camry Hybrid (54k miles back then, now at 62k) developed an obnoxious squeal coming out of the left rear wheel while driving at highway speeds. It takes several minutes at this speed to make the sound, so I believe wheel temperature triggers the sound. Touching the brake would temporarily silence it. After parking the car, I discovered that the left rear wheel was very warm, while the others were cool. I also saw excessive brake dust on the wheel.
I pulled the wheel to inspect. and saw that the track of the brake pad had moved a millimeter or two up the disk, so now part of the pad was over the "rusty" portion of the disk. The rusty, unworn part of the disc was thicker, so the part of the pad that was now over it was rubbing. At higher speeds, the rubbing would heat up the wheel and I'd gradually get the loud squeal.
I dismantled the pad, cleaned it, tightened the mounting brackets (via slight bending) and put it all back together. This solved the problem for 8 months. It just came back to haunt me on a recent highway trip...
It's a pain to take it all apart, especially if I am only temporarily fixing the issue. The pads still have over 85% live (including the rubbing one) and the disks look great on all wheels with no vibrations.
View 7 Replies
Is this repairable or would it be better to just replace it ? Ive never rebuilt one of these.
View 11 Replies
I have an '04 Toyota solar a. In 2012 I replaced the rear calipers and rear break pads and rotors Now 18 months later I have been told that my rear caliper piston is frozen and I have to replace both calipers and beak pad and rotors. Does this sound reasonable. It will cost me another $600. What should I do
View 11 Replies
I have a 2005 chevy malibu maxx. The front driver side brake caliper does not retract unless i open the bleeder screw. if I leave it overnight it will retract until i have to use it a couple times then ill have to open the bleeder screw. I've been told if the piston retracts when i open the bleeder then the caliper is OK. What i should look for? (It does have ABS).
View 2 Replies
I'm working on a 2007 Camry and I had the wheel bearings pressed in & out at a shop. I put everything back together but the driver side rotor is rubbing against the caliper bracket. And there is no air gap between the rotor and bracket so it can spin freely without rubbing. The passenger side is fine, there is a little air gap so the rotor can move freely without rubbing. I don't understand why the driver side rotor is rubbing against the caliper? I checked everything over, the pads and rotor are the correct ones. I also took the pass side caliper bracket and installed it on the driver side and same thing, the rotor still rubs against the bracket.
View 13 Replies
I'm having a tough time separating the brass fitting, even using a 10mm wrench. I noticed it moves below the bracket, so I'm trying to hold the oval with square corner base on the hose itself, but even then, have started to round the corners on the brass nut.
I'm gonna continue with the job, leaving the old hose, and will have to come back to this later, because I'm installing a new caliper (old one froze, and I just found out why, broken lower slide).
Any trick to separating the fitting between steel brake line and rubber?
ETA, to replace the brass fitting, does it mean cutting the tube, inserting another fitting, and flaring the end? I hate to leave the old hose or a rounded nut.
View 8 Replies
This is the 4th/5th/6th Gen Camry TRD four pot BBK setup. Theses are lightweight racing-inspired four pistons aluminum calipers. They will need Iconman's custom brackets to fit on Toyota models. Based on the cheap Highlander BBK thread, the caliper mounting bolts are in the same location so this setup will likely also work for 4th, 5th and 6th gen Camry as well. I have them on the 2003 Camry.
The OEM 2003 Camry caliper, bracket and bolts weights in at 8lbs. The TRD caliper with mounting bracket and bolts weights in at 6lbs. I know this doesn't sound impressive but consider the 4 pot calipers are larger in every aspects compare to the twin pistons Highlander caliper which weights 12lbs.As you can see the clearance between the edge of the caliper and the balanced wheel weights are very tight, and even with the 10mm spacer, the inside spokes of the Solara 17'' rim to face of the caliper have little room for play. 17'' rim are smallest size you can run with this setup. I also had to use extended studs and 10mm slip on spacer.
View 14 Replies
2005 Toyota Solara my front driver side caliper was sticking and heating up a couple months ago... replaced the caliper and the rotor... still had the same problem. I would drive it, it got hot and stuck, after I parked for a little while it slowly released. Talked to a couple of mechanics and they both said undoubtedly I had a bad flex hose and it was collapsing with pressure and then will release... I changed the flex hose and flushed the fluid and it was immediately fixed...no problems.
Drove the car for a month, went to South Carolina and back and then a couple days ago the same thing started happening. Talked to a mechanic, he told me that the new caliper may have gotten fried from over heating before I changed the flex hose... Got a new caliper today (warranty) exchange... changed it out and still have the same problem. When it sticks I can release the pressure by opening the bleeder valve so it seems like the flex hose issue again... my only thought now is maybe the new flex hose is a bad one and someone mentioned the proportioning valve.
View 9 Replies
So, my right, rear, brake caliper froze in the open position a little while back; I hit the brake hard, it held, heard a clack, then it let go and stayed in the open (uncompressed) position. I lost some braking power but at least have been able to drive. No visible brake fluid leak, other three brakes working fine.
At 125K, I've decided to do a full brake job, and am about to search for some of the parts on the awesome stickied parts reference list up above. I'll hopefully find some parts are available at NAPA, where I'm also ordering the right side cv axle.
So, I'm only finding remanufactured brake calipers at NAPA. Are they decent or should I look for something new elsewhere?
View 14 Replies
My girlfriend's 2005 Jetta has started intermittently leaving its lights on after she locks the car. It seems to happen with the fob OR with the keys in the lock. It started a few weeks ago with just the left rear turn signal. Now it is starting to do all four corners and the repeater on the front fenders.
The lights don't blink, they stay on solid usually after doing the normal "lock blink" and noise. This obviously drains the battery so we've had to jump it a few times.
How to fix this? To me it is obviously something electronic, but I didn't know if I should look to replace relays/fuses/wires/etc.
View 2 Replies
My 2005 Prius has today developed a fault, the central locking won't open or close with either of the remote key fobs. I allowed for a strange coincidence that the batteries in both fobs could die at the very same time and replaced one, still not working. The mini-key in the fob will open/close the central locking (all doors plus rear hatch). But of course the alarm would sound as soon as I opened the door, inserting the fob into the "ignition" socket and starting the car silenced the alarm after about 30 seconds, but the remote fobs still won't operate the central locking or activate the alarm.
View 5 Replies