Camry :: 2005 - Ignition Cylinder Removal / Replacement
Feb 19, 2015
How do I get to the screws behind the ignition cylinder (where the key goes) to remove it and replace with a new one? Do i use a short screwdriver?
View 1 Replies
Feb 19, 2015
Advertisement
Santa FE SM (2001-06) :: 2003 - Ignition Lock Cylinder Removal
A few days ago my ignition key would not budge when I tried to start my 2003 Santa Fe. I tried all the tricks like turning the wheel. dry lube, etc but no luck. All indications are that I need a new ignition lock cylinder but I can't figure out how to remove it. I removed all of the plastic and metal shrouding below the dash but can't seem to find a hole to release the cylinder. I have also tried to remove the whole cylinder body assembly by disconnecting the wires and loosening the bolt that secures the "arm" from the ignition cylinder body to the steering column but that also seems to be secured in a way I can't figure out.
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: Ignition Lock Cylinder Removal With No Key
So I have a replacement steering column for my truck and need to swap out lock cylinders. My question is; since there is NO key, is there any way to avoid drilling out retaining pin. If I did drill it out am I entirely screwed'?
View 14 RepliesFord Super Duty (1999-2016) :: 2000 F250 - Ignition Lock Cylinder Removal
I bought my 2000 F-250 CCSB a while ago and it came with 2 keys - one for the ignition, and one for the doors/tailgate - may not seem like a big deal, but it annoys me to no end.
From my understanding, the truck had previously been stolen and had the driver's side lock punched, and then something happened to the ignition lock to where it had to be replaced - hence the different key. I finally got around to replacing all the locks so that I'd only have one key. I started with the doors, then moved to the ignition (which I thought would be the easy part). I've replaced several cylinders before and I know it should be simple, but for the life of me I can't get the cylinder out!
I push the detent, turn the key to run, wiggle and pull.... nothing. I can feel the detent push in, and the cylinder will move a little, but it won't come out. I'm not sure if this is something that just happens sometimes and there's a fix for it, or if I'm in a unique circumstance and my column was somehow damaged during the theft and that's what's causing it.
Ford F-150 - 1997-2003 :: 2002 - Ignition Cylinder Replacement Without Key
My boss gave me a 2002 f150 if i can get it started. No key and no paper work in order to get locksmith to replace key. The only way i have noticed to get it started is to drill through cylinder to get it out. Need to know how to get it going?
View 4 RepliesFord Escape / Hybrid :: 2003 - Ignition Lock Cylinder Replacement
I'm replacing the ignition lock cylinder on my 03 Escape. The factory cylinder has the little black "wings" that nestle around the key when inserted:
The locksmith says the replacement cylinder needs to have those same wings for him to be change it. Is this correct? The auto part stores have the regular cylinder (with no wings) readily available, but the one with wings is a special-order item and I need this sooner rather than later.
Plus, the wingless one includes keys while the other appears to have none.
Grand Prix :: Ignition Switch Replacement - Location Of Hole To Release Key Cylinder?
I have a 97 grand prix GTP that I am replacing the ignition switch on. I am having trouble locating the small hole on the key cylinder that I put an allen wrench into to release the key cylinder.
View 2 RepliesYaris/Scion & Vitz :: 2001 Toyota Echo - Ignition Lock Cylinder Replacement
The previous owner broke the key off in the ignition so I replace the ignition lock cylinder the problem is though even with the old one I can't turn the key to lock so it's stuck on acc. What I can try without replacing the entire column? Also it needs a catalytic converter, do I have to weld a universal one on ?
View 1 RepliesCamry :: 2007 V6 - Wire Unseated From Connector During Ignition Coil Removal
Any easy solution to reseating this wire in the connector? It got yanked out by accident when i was removing an ignition coil under the wiring harness. 2007 camry v6
View 3 RepliesAccord :: 2005 V6 - High Pressure Power Steering Hose Removal / Replacement
How to remove the "high pressure" power steering hose. I have drained the fluid, disconnected from the pump, and also from the rack. Removed the center clamp, and got it all "loose". However, I cannot seem to figure out how to "fish" the hose out. There is a long piece of metal tubing that connects into the rack, and it seems to be resting above some cross member that is not removable. Went to the library, and searched the AllData Online manuals. On the "How to replace the High Pressure Hose" page, it only showed a diagram of the power steering system, with no written description on how to remove the hose. I am not on a lift, but jacked up and supported and on my back under the car with the right wheel removed. I am stumped, and the new hose is due to arrive soon.
View 2 RepliesAvalon 2005-12 :: Check Engine And VSC Lights Came On - Ignition Coils Replacement
I have 06 XLS with 56,000 miles and about 3 weeks ago the check engine and VSC lights came on. It was fixed, a ignition coil on the 4 cylinder.
Now driving home today the check engine and VSC lights are on again! I was wondering should try to get the dealer to replace all the remaining ignition coils ?
Plus I read their was some type of manufacturer defect on the original ignition coils from the factory. Why Toyota won't recognize this issue ?
Two ignition coils in a little over a month . My first Toyota and I'm rolling with the punches .
Ford F-150 (2004-2008) :: 2005 - Cylinder 5 Misfire - Spark Plug Replacement?
I am getting a cylinder 5 misfire and this has been a "on again off again" situation since last August. I took it around to a few places and the general solution was to get new spark plugs. After doing a bit more research I was advised to change the coil cover. I did that and it fixed the problem. Then about 4 months later the light came on again. I happened to change the air filter and the light went off. I though great, problem solved! not so much, when i went to the mountains the other day the light came back on. I did my research again and I have decided to get the plugs changed. Its a 2005 f150 with 94,500 miles on it.
I am told its time to change them regardless. I started calling around and getting quotes and have been told by multiple shops that ford made the plugs in my truck in a bad way. They have been telling me to change them and breaking them is a 50/50 shot. THEN, when they quote me they charge a rate to replace them plus the plugs themself. If they happen to break one then the customer pays for the new one. Do the plugs would really break that easy and should I plan on replacing some of them?
Camry :: 2005 LE With Manual Trans - Key Comes Out Of Ignition While Driving
I have a 2005 Camry LE, 4 cyl with manual trans. I was driving down the road yesterday and while I was driving the key came out of the ignition! My vehicle did not stall and I could easily put the key back in with no issues. vehicle still starts, runs, ign cylinder turns just fine, everything with no problems. key just freely comes out of the ignition with the engine running. I am going to assume this is not normal for Toyota. I know it isn't for GM vehicles.
View 2 RepliesCamry :: 2005 Check Engine Light Not Coming On When Turn Ignition On
I bought a 2005 Camry 4cyl yesterday and realized today that the check engine light was not coming on when turning the ignition on. I put my dtc tool on the car and got these codes. Getting P0300 ,P0303, p0304 & p0012 . Not sure where to start looking.
View 4 RepliesCamry :: 2005 - Dash Power Outlet Replacement
2005 camry ... How do i replace the dash power outlet? I have the heating and air panel out and the bottom of the outlet panel unsnapped. I can't figure out how the top comes loose.
View 1 RepliesCamry :: 2005 LE 2.4 - Engine Runs Rough / Loud While Driving And Cylinder Misfiring
I bought a 2005 Camry LE 2.4 4 cylinder. It was rather loud while driving, but especially while accelerating. It had error code P0420 from the beginning. It had a completely broken torque strut which I eventually replaced. Afterward since it toned down the kicking from the engine, I was able to notice that I could feel and hear the engine kicking like a cylinder misfiring. The computer gave me error code P0353 (Ignition Coil C Primary/Secondary Circuit Malfunction) consistently, and only a couple of times gave me error code P0500 (Vehicle Speed Sensor Malfunction) which went away.
I swapped the ignition coil and spark plugs around but the error code would persist on the same cylinder. The spark plugs didn't look particularly worn but I'm not experienced on what bad plugs look like. The codes persisted still, but later on P0353 went away, and the obvious kicking stopped but it still ran with a lack of power and hesitating on acceleration along with a strong smell of fuel in the exhaust. I measured the resistance of each fuel injector and all measured the same. I removed and flushed each of them with cleaner, but same situation.
What do you think? I don't get the bad cylinder code anymore but something is clearly wrong. Bad fuel injector? Bad wiring harness? Bad compression or head gasket (maybe from the movement of the engine while the torque strut was bad)? Hopefully not the computer... And could the loud noise be related to this problem or is that probably just a cracked exhaust from when the torque strut was allowing engine movement?
Accent LC (2000-05) :: Rear Brake Drum Cylinder Removal?
I must replace my driver's side rear brake drum cylinder but I am unable to fit any socket or wrench on the backing plate bolts holding on the brake cylinder. They are rusted and never been touched I think; how does one remove the bolts holding on the brake cylinder without stripping them? There is basically no room for leverage and the walls of a socket are too thick.
View 3 RepliesCelica :: 96 ST 7afe - Engine Removal / Replacement
I an taking out a 7afe engine (1.8L) from my 96 Celica ST to replace it. I have everything off the engine and all bolts removed from the engine to the transmission and there is no room to remove the engine. Does the transmission have to come out with the engine? I pulled them apart with what little room that there is and the clutch/pressure plate is stuck to the flywheel (the flywheel would clear by itself). This is a manual tranny.
View 2 RepliesPrius C :: Radiator Cover Removal For Horn Replacement?
Just received a set of new horn kit from piaa.. Now wonder how can I remove the radiator cover properly for the horn replacement.. Or do I have to remove the bumper?
View 2 RepliesGolf VI R :: 2012 - LED Fog Light DRLs Replacement / Removal
So looking to replace the passenger side front LED fog light assembly as the one that's currently on the car has a bad seal or something and lets water in. I have a new LED assembly but I'm lost with how exactly I'm to get the new part in. I've searched for diagrams regarding the replacement of the part and found one diagram that said the front bumper had to be completely removed from the car but I find that a bit hard to believe... (Then again its euro so maybe it's not hard to believe). Can the lower intake grill on the passenger side not just be pulled out or something? 2012 Golf R MK6....
View 2 RepliesPassat (B5) :: Right Side Drive Shaft Removal / Replacement
From what I've read, the procedure for removing and replacing the drive shaft involves pulling the upper ball joints and tie rod end from the steering knuckle--is it possible to put a floor jack below the lower arm (the load runs to the spring through the lower arm) and undo the lower ball joint to get the clearance required to remove the shaft?
View 9 Replies