Camry :: 2004 - Spark Coil Connector Holding Crack Off?
May 18, 2016
Scheduled maintenance for changing spark plugs for my Camry 2004 2.4L is either 120k miles, or 144 months (12 years). My Camry reached 12 years first. In removing the coil connectors, 3 of 4 holdowns cracked off. I guess not so surprising after 12 years subject to engine heat. I'm NOT going to replace the connectors. Looking for a patch for this problem? Duct tape will just result in adhesive getting everywhere it shouldn't. Maybe there's a high temperature "crazy glue" I could apply at the connector interface that will last another 12 years, or 120k miles?
Otherwise, I'll use the "hope adhesive". That means I'll just hope the connectors don't work loose at a bad time.
View 6 Replies
Advertisement
I replaced my valve cover gasket yesterday on my 2004 Camry. While putting back together, three of the tabs on the connectors for the ignition coil harness snapped off and would not stay together because of tension on the harness. I tried to zip tie them because I read that in another forum post but the clips (alligator clips?) inside the connector did not seem to be making contact with connector on top of ignition coil. The car was mis-firing and running very rough.
After much frustration, I finally removed the wires with the alligator clips from inside the connector and plugged them directly into the top of the ignition coil. Well, the car started and seems to be running/idling fine although now the Check Engine Light is on. Also, I have not driven car yet.
My question: Can I drive the car like this or will the vibration from the engine eventually loosen the connections. I am planning on ordering the connectors but they will not be in for a few days and I need to drive the car.
View 1 Replies
Any easy solution to reseating this wire in the connector? It got yanked out by accident when i was removing an ignition coil under the wiring harness. 2007 camry v6
View 3 Replies
Changed the spark plugs on my 2006 Camry today. Everything went smoothly and quickly except for the fact that I broke all the little keeper clips on the connector plugs that connect to the coil packs. I called my Toyota dealers and one said I had to replace the entire wire harness. The other found the connector plugs for around $8 each. Will the broken clips be a problem with the connectors eventually coming off from vibration if I don't replace them? I'm not sure how to replace the connectors if I go that route. How to go about replacing the connector plugs?
View 7 Replies
I changed out my plugs. The plug connector on the #3 coil no longer snaps on. My only option is to use a small ziptie to hold it in place. Can cut it off and wired a new plug end on..
View 3 Replies
My 93 camry v6 has spark jumping all over the place from the coil wire.I bought some new plug wires but only used the coil so far to see a minor improvement.I'll wait till it's dark to see where and if there is any more leakage.Plug wires are only 5mm thick.Is there something better than this(duralast) out there?
View 2 Replies
2004 passat 1.8t. How do I remove the coil packs on the top of the spark plugs, so I can repalce the plugs.
I unclipped the wire and unsure how to pull the coil pack off.
No bolts. can turn it and maybe pull, but doesn't budge and don't want to break.
View 3 Replies
I had squirrels eat wires to the front 3 Ignition coil connector on my a 2005 ford escape XLT,my question is the new connectors have a white and black wire and the old ones had a red and a colored wire, but comparing both old and new connectors I notice the new connector has the black wire where the old connector has a red, so do I use the black wire to replace the old Red? , it's rather confusing to me when you plug in the new connector you can see the black wire is where the red wire was on the old one, or does it matter which wire goes where?
View 2 Replies
Bought my car three weeks ago. I was looking around under the hood and noticed that the color of the connector on the spark plugs is different. Two are grey and two are black, in alternating order. What's up with that?
View 5 Replies
Here we go again. shut my 87 F150 5.0 off when I got to work when it was time to leave no spark from the coil, same as 3 weeks ago. First thing I did was pull the new dist and replace it nothing, so I pulled out the new coil still nothing, its getting power to the coil so I would assume the relay is good .
View 4 Replies
I have a 1991 Volvo 940 SE with turbo and 162,000 miles
The problem is there is no spark coming from the ignition coil. There is power going to the ignition coil but no spark. The car turns over but doesn't start.
I have replaced the crankshaft sensor and the Ignition Module. The wire that goes from the ignition module to the Ignition Coil has been replaced with a new wire that goes directly from the module to the coil .
Also the coil has been checked and its operating within parameters.
View 16 Replies
My Celica is running great, I drove about 30 miles and the car started hesitating to run, I was in heavy traffic, I could hear rattling sounds which appeared as though they were coming from the heater. I stopped at a stop light and I could tell something was burning out. I have lots of power, car is very fast. I went to the next stop light and the car died, it started and I went to the next stop light with plenty of speed and the car died and would not start again. I tried starting the car for 3 hours, no fire from the coil.
I have no spark out of the coil. I am confident the coil is good. I have 2 coils. I went to the salvage lot and purchased an "igniter" (ignition module). I installed it on my Celica, still no fire out of the coil. I have a relay under the glove box that clicks when I crank over the engine. The engine cranks over very well for over 3 hours. I have an after market alarm. Why do I not have spark out of my coil?
View 1 Replies
'91 Nissan NX 1600.It does not start., No spark from the coil which I've tried replacing, and the wiring tests fine everywhere before that. It's been sitting like this for going on two years, I think.
Background : Right before this started happening I replaced the clutch disk and flywheel, as well as complete timing, sprockets, guides, even the cover. About a week after that the fuel pump stopped, after I replaced that I hear it prime, but now I have the no spark problem.
View 2 Replies
'91 Nissan NX 1600.It does not start., No spark from the coil which I've tried replacing, and the wiring tests fine everywhere before that. It's been sitting like this for going on two years, I think. Background:Right before this started happening I replaced the clutch disk and flywheel, as well as complete timing, sprockets, guides, even the cover. About a week after that the fuel pump stopped, after I replaced that I hear it prime, but now I have the no spark problem.
View 11 Replies
I've been doing the 40k service to my R32, and was in the process of changing the spark plugs.
The first three went smooth with no problems, the next three however.... When I pulled the coil packs off, they were covered in rust and corrosion.
The inside of the block leading down to the spark plug (where the coil pack was) also had rust in it. I haven't pulled those three spark plugs out yet. What caused the rusting?
I assume I need to replace these three coil packs, and clean off the existing spark plugs before removing them. Is that a fair assessment?
I haven't had any trouble with misfiring or stalling. The car has been running great.
View 2 Replies
1996 Ford F150 5.0 ... New battery, new alternator, new starter, new coil, dis cap good and rotor is good. New plugs and wires. Ignition mod tested good.
Drove a mile from my house and lost power to my engine. Lights and radio work. Just sits there and cranks and cranks. I'm not getting spark from the coil. Don't know a lot about engines.
View 6 Replies
1998 Ford Explorer. Coil pack isn't putting out spark to that cylinder. Would the next step be to replace the pack, or might I check something else 1st?
View 5 Replies
I have an 86 f250 i just bought back with no spark. this truck is not original. used to be a diesel. has a 400 out of 81 f250. had this truck running just fine 4 years ago. sold it to a guy running and bought it back 4 yrs later not running.
Checked all the connection to make sure they r clean. Had the ignition modular tested and tested good. I have 12+ volts from the white and red wire. I have a little over 6 volts at the bat side of the coil. I have no spark from the coil. I notice every time I connect and disconnected the bat cable I will get a spark from the coil. i ran a test light from the tack test sight on the coil and tried to start and the light stayed real dim and never flickered.
View 1 Replies
Have a 2006 Ford Taurus that has two dead cylinders. Cylinder 3 and 4. Code says bad coil. I replaced with new coil and plugs. Same problem. Replaced wires and same problem.
Car has 65K. What is causing both cylinders to be dead? Pulled wires off while running and no spark on 3 and 4.
View 9 Replies
I have a 2002 prius that threw a spark plug and loosened the coil pack. The mechanic just reinstalled the plug and tightened the coil pack and said it was fine. Why it would throw a spark plug?? It was running fine, no warning lights, i just heard an unusual slight noise and opened the hood to check it out, and notice the loose coil pack over the first spark plug
View 2 Replies
I have a 1998 JGC. 4.0L motor. Driving it around town the motor would just shut off. Used to do it once in a while....then started happening more and more. I replaced the spark plugs, wires, cap and rotor....thinking maybe it needed a tuneup. Sometimes it restarted right away (right after it quit). Sometimes it wouldn't start until the next day.
So two days ago, daughter was driving it home from work and the motor just quit again. This time it will not restart. Motor cranks over fine. I read on this forum that this is a sign of a bad CPS....although a bad CPS will usually allow you to drive home eventually. So I replaced the CPS. Cranked it over....no change. Now, to check for spark and fuel. I turn on the ignition...I hear the fuel pump in the tank going. Then I pull the coil wire (brand new since I replaced all wires)...and put a spark plug on it....crank the motor....and NO spark. I then pull the wire harness that feeds the coil. It's a 2-prong plug. I turn on the key and nothing showing on the voltmeter.
I then put the volt meter on the battery and it reads fine. So I follow the coil harness connector back...and it just goes into the main engine harness. I then put the OBDII reader to the port in the Jeep and turned on the ignition. I get "Link Error".....so it's not getting a read, but the cigarette light is working...so the port is fine. So no spark to the coil harness and the Link Error does this mean a bad ECM (computer)? Also note that the fuel gauge (and maybe other gauges) are not registering when the ignition is turned on. The check engine light is not on. Maybe security system? I thought a security system failure would turn off spark AND fuel....but I hear the fuel pump running.
View 6 Replies
