Camry :: 2003 LE - Grease Or Oil In Throttle Body
May 1, 2012
So i recently bought a used 2003 camry le 4cyl with 72k miles on it. So it's still in good condition. Previously I had a 92 camry 4cyl which is run with throttle cable. The new generation camry's now are drive by wire or driven electronically. So I decided to check out the whole car and looked into the throttle body, the out side of the butterfly plate, and notice some thick black substance. It seems like grease or oil. I don't know if its there to lubricate the motor to run the plate or just oil.
View 8 Replies
Advertisement
I cleaned my throttle body this afternoon.
My car started fairly easily, and I continued with running it to 4k RPM a few times, then took it for a ride. I floored it a few times, as suggested, to clear everything out.
Now, my 2004 J-VIN Camry is running around 1200 RPM, it was at about 650-675 before the cleaning. Is this normal? Do I need to d/c the battery to reset the ECU so the car can re-learn with a clean TB?
View 5 Replies
I have a 2012 Camnry I4 and want to clean the throttle body.
Is this throtte the type that I can manualy open valve by hand without damage, or does the pedal need to be pushed to open, to prevent computer or throttle timing issues?
View 7 Replies
The rpm with the A/C on are 550 , I was told to replace Throttle body, I did, rpm continue the same,when im driving and I stop the car start vibrating, some one told me that i have to program the new throttle body , how can i do that?
View 3 Replies
I've tried searching everywhere, but can't seem to find the torque for the 4 bolts holding the throttle body to the plastic intake. This is on a 2az-fe engine in my 2004 camry. I imagine the torque would be the same for any Scion, RAV4, etc. that has the same engine.
View 4 Replies
About, one month ago my car shut off while driving(pretty scary at the time). I pulled of the road and attempted to start it again. Everything looked good there, but as I was making my way home from work it started to act funny. It would not acknowledge me depressing the accelerator. When I got home, I ate supper, then went to have a look.
The car would turn on, but not acknowledge me pressing the accelerator at all, It did however go up to 30 mph at a snails pace as if it was coasting down a hill. I plugged in my code reader, and it read that the Throttle Body Valve was stuck open. I took it off and tore into to it a bit. I noticed the gears inside the TB itself were corroded and the butterfly valve was locked up.
I replaced the part, and tried to turn my car on with the new TB. All the dash lights are in working order, however upon turning the ignition to crank the engine, the whole car system shuts down. No lights no nothing, besides the car door open sound. The car will remain like this regardless of the key position until I have reset the batter(take off the terminals and put them back on) to which the process repeats itself.
The code reader says no codes are stored because I obviously reset the battery. So now am at a standstill.I believe the old TB froze up, because I had to run in through 3 ft standing water during a storm, and then deployed shortly after(I'm in the service) for a few months while letting the car sit.
View 1 Replies
I have a 2004 V6 LE with about 135k miles. I cleaned the throttle body two weeks ago, just because I hadn't ever done it. It wasn't too dirty. Before the cleaning, it idled at < 1k revs. Now, when I start the engine cold, it revs at around 1500, sometimes higher. It goes back to normal after the engine warms up to operating temperature.
Also, I hear a very slight high-pitched whining (maybe hissing?) noise when I accelerate. The noise is more prominent when the engine is cold. I checked for vacuum leaks but couldn't find any.
It feels like I'm depressing the gas pedal a little bit when I have it in drive or reverse, and it wants to pull harder than usual. When I bring the car to a stop with light brake pressure, as it drops into first gear, the car gives a slight tug forward, again, as if the gas pedal is depressed. I mention this to show that it's not just an issue with the rpm at startup.
I suspect that the issue lies with the throttle position sensor, which I may have jostled when I moved the throttle valve. The method I used when cleaning was, I first tried opening the valve by hand with the ignition off, but the resistance was much higher than I had anticipated. So I did the key-in method by turning the ignition to ON and putting a brick on the gas pedal. There was a high-pitched whine coming from somewhere in the engine bay when the key was ON, which I had not noticed before; I wonder if that is normal.
This seems to be a rather common issue after cleaning the throttle body cleaning, but there doesn't seem to be any consensus solution besides to wait it out.
View 6 Replies
2002 Camry XLE.
I cleaned my throttle body today. Since the throttle plate moves by a motor, in order to keep it open, I turned the key to ON and held the gas pedal down by using some weight.
After I put everything back, the idle was high 2000+, then stays at 1300 to 1400 range. I drove about 10 miles and it is still the same. When stopped at a light in drive, the idle is still 1000
Did I mess up the e-throttle or the throttle position sensor? (Since I used a weight to hold the gas pedal down, I am worried now).
View 5 Replies
2002 V6 Camry 145,000 miles, cleaned throttle body with TBC fluid, now starts runs for a few seconds and dies. In order to open the butterfly in cleaning I turned ign on and propped pedal down. After cleaning the car ran better but idle was high and a little erratic. I disconnected the neg batt for several hours, now it starts, but dies right away. In the cleaning process I had removed the throttle control sensor an reinstalled it. Can't keep it running long enough to adjust it.
View 8 Replies
I recently cleaned the throttle body and now it surges up and down. Not really sure what to check next. 2002 toyota camry 4 cyl.
View 3 Replies
I have a huge problem. I was installing an air raid throttle body spacer while talking to a friend on the phone. While talking, I accidentally dropped one of the bolt spacers down the throttle body intake. Is there any way to get the spacer back without having to take the intake manifold off.
View 3 Replies
Its a 2006 Toyota Camry 2.4l.. its been sitting for about 4 weeks now which has given me and her some personal time...I cant get it to run without me covering the intake hole. Last night my girlfriend and I were tinkering with it... before I sprayed carb cleaner and sealed the hole off with my hand she pressed the gas and I heard a grinding noise. So I told her to pump the gas with the ignition on and the gas peddles and the grinding noise was synchronized in timing. I turn the ignition off and press gas nothing... I'm guessing that's because its a fuel injected vehicle and everything is electronic (ECM) also I noticed when you cycle key from on to off it makes that noise also... won't start and I need my car.
View 4 Replies
I have a 2009 Camry which has the well known very bad vibration at idle when in drive at a light. My Ultragauge shows the RPM are very low when it vibrates. Sometimes it drops to around 425-450 rpm when at a stop light in drive (automatic car). Then it sometimes moves up to around 625-675 rpm and that is when the vibration completely disappears and it is nice and smooth. This issue is intermittent but happens everyday.
Most people think it is due to a bad engine mount and spend money doing that and get no results.
I have done a lot of research and feel it is due to a dirty throttle body and IAC valve and want to test my theory. I will post results once I do the job. What is the easiest and most thorough way to clean both?
View 6 Replies
I need to clean my throttle body on my '97 F-150 and it has a label saying not to clean directly. Is it still safe to use TB cleaner and to go ahead and clean it? It needs done but how would I go about it.
View 6 Replies
2002 camry. The car will not accelerate. The throttle body makes a clicking sound when pedal is depressed.
So.. I took it apart and cleaned the contacts in it. In the mean time located a spare throttle body from a 2003 from a local yard. The old throttle body has a part number 22030-28030 and the replacement has a part number 22030 0H010. The replacement throttle body wouldn't even move when the pedal was depressed.
I put the old one back on.. and now it doesn't click anymore but the car in Park only revs to 2000 rpm's. Its not sticking or having any mechanical issue.
I checked the parts site for Toyota and the replacement is the new number. Superseded. Does the throttle body after replacement need to be reprogrammed? Or whats the deal. I wish I was more Toyota literate when it comes to this.
View 1 Replies
The Throttle Body on my 2001, 4.6 L is making a strange whirring noise, when you puy your hand on the intake pipe, you can feel a slight vibration. The Truck idles and runs okay, with no codes. Giving it a little gas and the noise goes away. The last thing I did was clean the IAC with Gum Out Carb cleaner, the second or third time I've done this over many years, with no problems. I'm a little perplexed at the cause.
View 6 Replies
I'm usually over in the EX forum but today was working on my brothers 1998 F150 - V8 4.6L. Had the EGR code P0401 and due to FTE I found the problem took the throttle body off and found it was definitely plugged. One of the bolts was really loose and came off way to easily. Didn't realize until cleaning why... Now I drilled 8 studs out of my aluminum EX heads but this one has me pondering how I'm going to clamp this thing down and center a bit..
1st pic - ports WOW - guessing this was the problem ...
2nd pic - bigger issue ...
3rd pic - the ports cleaned up ...
View 8 Replies
I have a throttle body noise that sounds like a warble,It is sporadic and I think it should not be their. But I have heard some other f-150s make the same noise. Is it normal or is something not right.
View 3 Replies
I busted the cable end by not removing it properly. My question is what is the proper method of remove the cable from the throttle body? Are the cable ends replaceable? If so who has them as a google search didn't find any? I've tried to find written information but haven't any luck. bl2009
View 1 Replies
I accidentally broke the control lever where the cruize control attaches. I've looked all over but I can't find the lever. Where I could buy just the lever? New throttle body is more than I want to spend.
View 1 Replies
High mileage 1999 4.6 4wd 5 spd: Needed to replace the rear ABS sensor and decided to clean the throttle body too while the battery was unplugged. Cleaned it around the butterfly and not much else. Truck idled at 750 BEFORE cleaning the TB. Now it fluctuates between 820 and 950 rpms. Also tends to stay at a higher rpm after pushing in the clutch and taking it out of gear.
Did a thorough check for vacuum leaks, nothing. After research, I cleaned the IAC and re installed (battery was disconnected then too). No improvement. Unplugged the IAC while running- ZERO change in idle. Installed new IAC, no change whatsoever. Unplugged NEW IAC, no change whatsoever. Is there an issue with the PCM needing time to fully re learn? Am I missing something.
View 14 Replies
