Camry :: 2002 V6 SE Running Rough And Stalls At Idle
Mar 26, 2014
My wife has a 2002 Camry V6 SE with about 75k miles. Over the past 6 months the car has developed a problem. Every so often, say once every 2-3 weeks the car will start fine, but after driving for about 5-10 minutes, will start running rough and stall if I stop for a light. It will start again, (with a little effort) and will stall again at the next stop and so on. I can pull off the road, wait 10 minutes and the car will then run like a Swiss watch until the next episode.
I have taken the car to a respected mechanic and he sees nothing obvious wrong and there is no record in the car's computer of any problem. The last time this happened the car had been on the road for about 20 minutes before the stalling problem occurred. I kept the car going at idle by putting in neutral and increasing the throttle.
After we arrived home, the car cut out when we made it into the garage but a rotten egg-like smell was in the air in the garage. After about an hour, the car stated immediately and ran like a top. That was about a week ago and no problems since. I have read in the threads about EGRs Throttle bodies etc.
View 4 Replies
Advertisement
Since having dealer work on my brakes: replaced booster and brake light switch. While at the deal the changed all the fluids. Now my EX has been intermittently stalling when stopped in drive with AC running. When it stalled the OD light was flashing. Now we have noticed that the EX is sputtering when stopped while in drive and may stall. Also, itermittently seeing the the ABS light come on. Today it stalled and now the CEL is ON.
View 14 Replies
I have a 2002 camry that stalls out while driving. The car stalls when engine is warmed up and the car is running at appropriate temperature. When this occurs no "check engine lights" stay on and the car re-starts after 15-20 minutes and runs just fine. I had the car looked at by a Toyota dealer and another independent shop and they where unable to pull any codes from the computer module. The car is up to schedule with routine maintenance items. The car is garage kept and I go to the same gas station each fill up.
View 2 Replies
today I replaced the battery on our 2002 Camry SE 2.4l because it was incredibly slow to crank today...but it did crank. So i get a Duralast Gold to replace a Toyota TrueStart battery, and it started up fine. However, it was idling at 200-400 RPMs, so its already not right. So I drive it a quick mile or so, and when letting off the gas the RPMs drop to 200-400 while going down the street! Coming to a stop, it really wanted to stall out. Couple stops later, it did stall out, and the Check Engine light, Battery light, and Oil light all came on. Trying to restart it it cranked, started, but then immediately died. You know when you start it the RPM needle goes high and then comes down a bit? It does that, but the needle won't stop and it just goes to 0, and throws the Check Engine, battery, and oil light. I finally got it cranked, and all 3 previously mentioned lights are off when its running. It has done it one other time about 3 months ago when I disconnected the negative battery terminal for some work, and it did the same exact thing. It ended up just fixing itself, but obviously not since its rough starting and the problem came back the next time I disconnected the battery.
View 14 Replies
2002 Camry 4 cly was running great. All the sudden looses power, stalls (won't idle), engine light came on, when I held gas pedal at 1000 rpm engine rev's 1000 - 1400 rpm. Autozone trouble codes P0300, P0301, P0302, P0171, P0420. Car barely runs, getting worse quickly. I also smelled hot metal when I pulled into driveway, exhaust tail pipe was superhot.
View 7 Replies
Just got the battery replaced on my v6 Camry, had no problems before it. After replacing the battery, I drove about a mile to another stop and parked the car. Noticed it vibrating and the idles very low. I restarted the car and it wouldn't stay on. Car will turn on fine, RPMs will go a bit above 1k and drop down and turn off in about 5 seconds.
Today morning I started it and it seemed fine (cold start). Idles were about 1K on a cold start. Drove around about a mile and came home and the car stalled. Same as above, it'll start up and stall within 5 seconds.
I took it for a drive (about 25 miles) so the car can re-learn everything and took a stop at Autozone. Same thing there. Didn't stall on the way because I didn't have to stop, I was on the highway. One of the sales guys looked at the car and told me to try out a new MAF Sensor. Installed a new sensor and the car died off again within 5 seconds. Checked the readings of the MAF sensor (old and new) and they both read fine.
Brought the car back home (about 35 miles total driving after battery replacement) and it'll still stall as soon as you stop. To keep it going, you have to hold the brake and hit the accelerator very lightly to keep the idle in the middle of 0 and 1 or shift into Neutral and do the same.
No CELs on the car, car drove perfectly fine before the new battery. New battery tests good, even went to the extent of putting my old battery back in (Drove about 35 miles on new battery, replaced and drove 35ish miles). Car has just short of 100k miles. Regular services are done at Toyota at about 5-6k.
View 12 Replies
Recently replaced spark plugs and wires on 02 SL1 with 209K miles. Was running rough, rough and high idle, almost died on me driving home one night. After replacing everything, car still wouldn't start. Spent some time on the forums and some suggested a leaking intake manifold gasket, so I changed that out as well as the coolant temperature sensor. Still it won't start. I am getting good spark at the plugs (coil arcs across the posts when plugs wires are off).
Really not sure where to go next with this. I can hear the fuel pump hum when I turn on the ignition, and I get a good spray at the fuel rail. Basically I turn the key and it cranks, sputters, and will almost catch, but then not. What next??
View 2 Replies
I have 144,000 miles on my V6. Just started to notice that the car is surging/hesitating at just about all speeds. It appears to idle fine and if you raise the RPM in neutral I can't detect a problem. If you place the trans in drive, apply the brake and raise the RPM to 1000 to 1500 the engine's RPM varies slightly and regularly, it not steady like all of my other cars. When you are at highway speeds you can feel the car slightly buck, if you take it out of overdrive it is more detectable due to higher RPM. I do not notice the problem when the engine is cold.
I have a hand-held scanner and I see no codes and there is no CEL illuminated. I changed the plugs with OEM plugs at 90,000 miles when I changed the timing belt. Changed the air filter probably 10,000 miles ago. Just cleaned the MAF sensor (after the problem started), no change. Took it to the dealer. They discovered broken motor mounts which I kind of suspected I had, but I didn't feel the symptom were mount related. They said that I was feeling torque converter lock-up. I told them that the range of speeds and gears that the problem presented itself that it was unlikely lock-up.
Alldata suggests that it is a fuel problem and Toyota has some TSB's for drivability. I'm discounting the TSB's because this just started recently. Any hints as to where to try first? EGR, fuel regulator, fuel pulsation damper, injectors, spark plug coil packs, ..... It gets too expensive to just remove and replace the sensors that deal with the fuels system. I have plenty of tools plus a volt-ohm meter and a fuel pressure gauge.
07/21/2009 : While I was at work I added Seafoam to the gas, tank was half full.
On my way home from work I disconnected the EGR Position Sensor connector and the symptoms disappeared and the expected CEL illuminated. When I arrived home I went on Alldata and looked for an EGR system test. I found two, one for the position sensor and one for the EGR temperature sensor.
I had to run out to Sears to pickup a vacuum pump. I performed the tests below up to the point that I needed the pump. I also removed, inspected and reinstalled the EGR Position Sensor before I left for Sears. I did not notice the symptoms on the trip about 14 miles round trip. I'll see if I still have the problem on my way to work tomorrow.
Performed the on-vehicle inspection as listed on Alldata
EGR Position Sensor resistance: 2.6 ohms, in spec
EGR Position Sensor power: 5.0v, in spec
EGR Position Sensor output with no vacuum applied: 1.0v, in spec
EGR Position Sensor output with 5.1 in Hg vacuum applied: 4.0v, in spec
07/22/2009 : Problem seems to have gone away, no bucking or hesitation. Maybe the connector contacts were dirty on the position sensor. Will update if the symptoms return.
09/07/2009 : Noticed that I am getting 2 miles per gallon more than before I found the problem.
View 14 Replies
So my 2002 Camry XLE V6 with ~132,000 miles has a little bit of a rough idle. It sounds like it's "breathing". It'll be rough for a second, smooth for a second, rough, smooth. It's not super rough where my steering wheel is really vibrating, but definitely noticeable. The RPM hovers around 500-600 and doesn't really fluctuate. On Sunday, the following was done with a friend:
- All 6 spark plugs with DENSO SK20R11
- OEM PCV valve, grommet, and hose
- OEM Air Filter
- OEM Cabin Filter
- OEM plenum gasket
We didn't do the head gasket and manifold gasket to save time and there was absolutely no oil on the coils or plugs. The car was very well maintained by the previous owner and by me since I got it at ~102,000 miles.
The car seems to surge sometimes. I'm not sure if that is the right word. Say if I turn left up a hill and hit the gas, the engine RPM will kind of surge up and then it'll shift. It's audibly noticeable. It's not smooth, but maybe it's just because it's a hill, I'm not sure
The idle seems about the same since before we did the plugs, which I thought doing the plugs would work. It almost seems like it might be worse and the MPG might be worse, but that may just be in my head.
Could it be the front motor mount? Maybe we should have cleaned the throttle body while we had it open.
View 8 Replies
I have an 02 f250 V10 with a rough idle (90K Miles). It's not horrible but it's obviously not running perfect. Everything seems ok when I am up and driving, especially at freeway speeds. I recently noticed that if the truck is in park and I run the RPM's to 1500 or 2K and quickly let off the gas it will die. It never throws any codes. So far I have replaced the IAC Valve, fuel filter, O2 Sensors, PCV valve, cleaned the MAF sensor and replaced the air filter. Plugs and boots were replaced 5K miles ago. Fuel trim levels on both banks are running around -3.1 to positive 3.5 based on what the computer is telling me. Also according to the computer the vacuum sits steady around 25 at idle (+ or - .2). I don't have a manual vacuum gauge, just relying on the computer. I've also gone around to every plug and disconnected both the injector wire and the COP wire and they all seem to equally affect the idle as well as the fuel trim levels.
View 11 Replies
We've had two problems within the last week with our 2002 Sport Trac (4.0l SOHC engine w/167,xxx miles). They may be unrelated, but I suspect there's good change they are. Both incidents happened while my 16 yo daughter was driving, so there's only very limited info on what happens. Both times, when I get there, it starts and runs fine. There is no CEL.
The first time it apparently stalled as she neared her destination after driving only about 2-3 miles at 35 mph or less after a cold start. She was slowing to pull into a parking lot and reported the dash lit up with warning lights, no power steering assist and no power brakes and no power from the engine. When I arrived it started and ran normally. She had fulled up the day before after two days of heavy rain, so I suspected water in the gas. I drove it more than 200 miles within the next 24 hours under a variety of conditions and filled up at a different station. I experienced no problem what-so-ever, and didn't bother adding any dry gas.
Then 5 days later (still on my fill-up) when she tried starting it after sitting all day, she reported the engine started but ran rough before stalling and never idled normally.
Doesn't the fact there's no CEL eliminate a lot of the upstream part of the control system......like sensors and actuators? This leaves things like the downstream parts of the fuel and ignition systems. I.e. from the fuel tank / pump to the injectors and the downstream parts of the ignition system.
What are the possible culprits? Fuel pump, fuel pressure regulator, injectors, ignition module, spark plugs, and....... what else? (I'm not that familiar with what these engines have) And of the possibilities, what are the most likely causes.
View 4 Replies
I changed all of the brakes on her car yesterday, test drove it, everything was great. Put close to 100 miles on it w/ no issues. Therefore, I don't think it's anything I did.on her way to work, the CEL came on. The car has a rough-ish idle, and jerks slightly in low RPM. I went to Pep Boys and got it read. it threw 8 codes:
P0171
P1130
P0300
P0301
P0303
P0305
P0442
From what i've read, the p0171 is the system is running too lean and p0442 is a leak somewhere. The 300s are cyl misfires.I don't want to go replacing every conceivable part. What these codes mean in conjunction?
View 14 Replies
This is my brother's 02 SE. 140k miles. 4cyl. He claims that the car is beginning to idle rough when he is stopped at a stop light and the AC is on. If i replace the spark plugs should that do it? I'm pretty sure it doesn't have spark plug wires cus that's what my dealer parts dept said. Motor mounts were replaced around 70k if that matters. The vibration is directly related to the AC being on.
I am also going to replace the serp. belt because there's a belt squeak when the motor is cold.
View 5 Replies
I have a 2002 Camry SE (V6) with approx. 180K miles. The Engine mounts were shot so I decided to change them. I am a reasonably qualified mechanic (FAA Aircraft Mechanic) and perform most my work on my cars so didn't think this would be a big deal.
My procedure was to jack up front & put frame on jack stands then removed both wheels. Then with hydraulic jack and blocks under oil pan I started by removing all or the three lower engine mount hold down nuts (3 on bottom, 1 on top of each. NOTE: I changed the dogbone first which took 5 minutes.
I then jacked up engine about two inches or so and pulled out each old mount, then lowered engine back down making sure everything lined up as best I could. Then finished by tightening all of the nuts. Done. ....or so I thought.
When I went to start, the engine cranked but with a an unusual vibration and generally rough idle, more noisey than usual. When I drive it shift fine and everything works, just unusual vibration and noisey inside car.
I also used my BOSCH code checker and got ZERO CODES.
What is even more unusual is the engine when you are outside the car listening sounds fine. Just sitting inside do I sense the unusual vibration and noisy idle.
I checked for loose vacuum hoses, anything obviously pulled loose, etc and found nothing.
Again the car started and idled fine before the engine mount change now starts kind of rough and is noisy [inside car] but quiet outside.
nothing really changed except the moving of the engine block up and down to get the old mounts out.
View 7 Replies
2002 Toyota Camry
2.4 V4
My car has developed a rough idle when stopped and when accelerating. When I got the CEL, I had the codes read at Advance Auto.
The codes are P0301, P0302, P0303, P1349.
View 1 Replies
After a long trip from Houston to Dallas, my vehicle started to ride rough and eventually die on idle. It seems to idle fine, but then die after the first minute. I am getting code P306 and others all dealing with random misfires and misfires on ALL cylinders. The troubleshooting steps I have taken so far to no avail are:
(1) Replaced spark plugs with pre-gapped iridium
(2) Checked ignition coils
(2) Checked all vacuum hoses and air intake leaks
(3) Changed air filter(not a big deal)
(4) Removed and cleaned the throttle body with carb cleaner thoroughly
(5) Checked the intake manifold for leaks and did not find any.
(6) Computer PCM checked for updates and issues at dealer
The dealer said it needed new fuel injectors, which seemed kind of fishy due to the following symptom:
The car runs GREAT at highway speeds, but it is unable to maintain an idle for an extended period of time and dies due to misfires. I hear a chugging in the engine sometimes.
Due to these symptoms, I self diagnosed this as a fuel regulator?
View 14 Replies
I have a 99 Dodge Stratus 4 cyl 2.4L, automatic.
It has been idling rough for a few months now. It feels just like it is misfiring. Tach confirms quick dip in rpm then return to normal idle. It has never actually stalled, just a quick rpm dip and subsequent shuddering, then recovers for a few seconds.
Also runs very rough, at 47-48 mph under light "cruising" load. Sounds crazy, but it does (did, see below) not happen at 45 or 50, just in the 47-48 mph range. Again, it feels like bad misfiring, with the car losing a lot of power and shuddering until I accelerate/decelerate away from this speed range.
NOW, over the last few days, the rough riding has gotten a lot worse, and occurs at all speeds. It is worse under load (mild acceleration, hills). Still feels like misfiring. Loss of power makes it hard to maintain speed up hills, at any speed. Also, today for the first time in its life the car backfired while trying to accelerate up a hill from a stop, at a speed of about 15 mph.
When idling, I can occasionally smell gas.
So, the coils are 2 years old, spark plug wires are 2 years old, spark plugs are 2 weeks old and air filter is 4 days old. Check engine light is NOT on and there are no error codes as of yesterday. Fluids are all good, except I am about the kick the stupid thing until it bleeds. Parts store suggested Idle Air Control Valve, but I am dubious, as this now happens at all speed.
View 2 Replies
My fathers 1990 GMC Sierra 1500 Pickup Truck 4.3L runs fine when it is cold but as soon as it warms up it starts running rough then stalls and won't start. There is no spark when it dies. As soon as it cools off it starts back up and runs fine till it warms back up.
View 2 Replies
So I have been unable to figure this problem out and so had my mechanic, I am starting to think this car is cursed. I have an 07 outback with about 54000 miles on it, a few weeks ago it through a P0303 for a misfire in the third cylinder, thought nothing of it, light went off in the next couple starts and the car was running great. Had this happen a couple more times but only after the car had been out in the rain. Each time the problem went away. Now the car has sat in my garage for four days, I got out to start it and get an extremely long crank but no turn over. Try again and after 5-6 seconds car turns over but is running really rough and stalls out. Disconnected the battery checked hoses, everything looked normal, reconnected the battery and now the car is running fine.
View 3 Replies
The car will start up fine, run for 10 - 20 min and stall. I will try and restart it but i takes atleast 7 or 8 sec of the car just turning over before it slowly fires up. Which results in a high idle 1200-1400 rpm and the car stalling another 5 min later.
Ive fixed my o2 sensor the wire was cut, replaced the fuel filter, and got a eurojet lower pcv hose for the vacuum leak i found.
View 4 Replies
2002 elantra hesitates and sometimes stalls staring from rest. Worse when cold but still sluggish after warm up. Where do I start?
View 7 Replies
