Camry :: 2002 Solara SLE V6 No Spark - Timing Belt Broken?
Feb 15, 2016
2002 Toyota Solara SLE v6 w/ 209k miles
Drove the car home from church yesterday, this morning went to start and wouldn't start..
Tested the Fuel Pump and that looks good.. Pulled a spark plug and did a spark test and I get no spark.
After reading up I get the sense it is either the Crank Angle Sensor or the Timing Belt snapped .. I don't know the last time the timing belt was changed, we got the vehicle @ 190k miles..
Does a no spark symptom sound like a timing belt that could have snapped? I believe these are non-interference engines so it should be ok..
When turning the car over the RPM gauges doesn't look like it is moving but wanted to see for a complete spark failure.
View 2 Replies
Advertisement
I recently purchased 2003 gti with a broken timing belt i bought a reman cylinder head did the timing belt, water pump, belt tensioner, cam chain, and cam chain tensioner. I read the service manual and many forums before setting the timing. I got it all set and back together it runs great at the low end but it feels like when it starts to build boost pressure it stops making power. Would i throw a check engine light if the timing was any off? Would it run well on the low end and then lose power if the timing was off or should i be looking in a diffrent direction? I just want to make sure timing is not an issue.
View 1 Replies
1999 Honda Accord EX, 224K miles, 4 cylinder. Timing belt broke yesterday and ruined some exhaust valves. Also needs new radiator. Should I spend quoted approx $3500 for fixed cylinder head and valves, 30K mile check (plugs, valve adj etc), new radiator, might also include piston rings, not sure? Completely trust the mechanic. Other recent work already done is one new front wheel bearing and axle, new bearing boots on both sides, oxygen sensor, new clutch a year ago. Interior/exterior are in good shape. How many more miles am I likely to get on this engine if I have the work done? Will I likely need ball joints replaced soon? Anything else I should be considering?
View 8 Replies
I have an 01 subaru impreza with 185000 miles. The timing belt broke while I was driving. I gave the mechanic five-hundred for parts and labor but then he told me the engine would need to be pulled to fixed damaged head and valves.
View 6 Replies
I recently broke a timing belt on my 1999 AEB 1.8t Passat. I'm in the process of doing all of the repairs myself while working around my college and work schedule. I have yet to pull the head off, and I'm scared of what I'll find when I do. Should I expect any piston damage? I have one completely broken valve and a bunch of bent valves.
View 12 Replies
I think the timing belt broke on my 2007 4.0 6cyl that has 99k on it. Is this an interference or noninterference motor?
View 5 Replies
The timing belt on my 2004 Chevy Aveo broke last week. I have it at a mechanic who got a new timing belt on to check the compression of the engine. Bad news: no compression. So far they haven't taken the head off to inspect the inside. This includes timing belt/water pump, cylinder head gasket removal and replacement, cylinder head check, some misc labor, lube, oil, and filter...
However, another mechanic is suggesting that I replace the engine instead with a used or refurbished engine with less miles. He says that it doesn't make much sense to put new parts on the top end of the engine. The engine itself has about 153k miles on it.
View 14 Replies
I recently bought a 97 960. i have had a s90 before in totaled it i loved the car so much i found another. i was driving and broke the timing belt tensioner which in turn lead to the breaking of 5 exhaust valves that i know of. I've taken off the head and noticed that one of the bottom of the valves had melted onto the number 5 piston head.
I called around and search but every motor is at least 1000 and i have been told anywhere from 3500-4500 to rebuild. My question would b is there an easy way to fix or should i junk it. i bought it for a 1000 it has only 140000 on it an its in almost great condition. I attached some pictures of the head and piston so u can see the damage.
Attached File(s)
2012_04_07_19.02.39.jpg ( 1.45MB )
2012_04_10_16.45.26__1_.jpg ( 1.43MB )
View 1 Replies
95 nissan maxima decelerated on highway, i heard a clunking sound, and then it shut off, i opened the hood and it smelled like burnt rubber. Checked all of the belts i could see..no problems. Car wouldn't start after this...and all i could hear was a clicking sound. Pulled 6 codes for the car including bad speed sensor and a misfire, as well as bad EGR...i think the timing chain/belt broke..but i can't access it.
View 3 Replies
2.5 Litre ... Okay, I've done this on other cars, both Fords without a problem but now I'm stuck on the no start situation. I have spark and my fuel pressure is 60 psi. About to do a compression test. Only issue with replacing the belt is that no matter how many times I try removing and installing it I'm always 1/2 tooth off after rotating the engine a couple of times but that shouldn't be enough for a complete no start. Tried starting fluid. Replaced cam sensor. new plugs. checked firing order. I have spark at #1 according to my test lamp which plugs inline.
View 6 Replies
I drive a car I am extremely reliant on. I don't have money to buy a new one and I may be a bit over protective of this car. It is in excellent shape, I bought it with 96K and whoever owned it took good care of it. I changed the battery pretty much right away, and the auto parts store guy said it looked like it was the original battery. So I suspect the timing belt is original too, (along with the clutch, which works great BTW). I don't know anything about cars short of what I have heard on CT, but it seems there is a trend towards having to change the timing belt at 80-90K And I know that a worn out timing belt can have no symptoms and essentially ruin your car if it breaks.
I took my car for the blue plate special, and it has been to the dealer a couple of times for some repairs where they also do the general service and see if they can find something to charge me for and in all cases, my car had nothing they would identify and repair. Fluids are good air filters are good etc. When I took it to the little shop on the corner I got the same report, and when I picked it up I asked, well how does the timing belt look? And he said. I can't tell you, you would have to take it apart to find out. So my questions are, as I do not know if the timing belt has been changed by previous owners. should I just go for it and have someone change the timing belt as part of my regular maintenance plan now, or is there some nifty way to find out if it needs changing without having to spend an arm and a leg?
View 9 Replies
About a year ago after I got my oil changed I assumed they spilled oil when filling it at the shop. I actually had smoke coming through my vents at first. The smell has been there intermittently ever since but only when the heater is in use, not when AC is used. What could have been the cause? What should I check? Is there a cabin air filter that should be changed?
View 6 Replies
I bought 2002 3.0L Solara with some issues, one of being a miss fire. What should the resistance be, and which terminals should I be using?
View 1 Replies
Two of my plugs locking clips broke today on the wire harness side where the coil over plugs into the harness today while changing spark plugs. They will plug back up, but they won't lock together like they are suppose to. How critical is this? It is my wife's car will she break down? I drove the car maybe twelve miles, and everything seemed fine.
View 8 Replies
I recently changed the timing belt on my 2001 Avalon. I am now getting a P1351 code. I removed the timing belt covers and checked the marks, and everything lines up perfectly. I have checked this twice now. To give a little background, before I changed the timing belt, I was getting P0300, P0301, P0303 and P0305 codes along with a P1349. Upon looking up the codes, P0300 indicates a misfire on multiple cylinders, with P0301, P0303 and P0305 indicating misfires on cylinders 1, 3 and 5. The P1349 indicates a variable valve timing issue on bank 1 (cylinders 1, 3 and 5).
I had already changed all 6 coil packs and fuel injectors and spark plugs within the last year (iridium plugs), so I pretty much ruled out any of those. And since the valve timing code was on the same bank as the misfires, I figured that was the cause of the misfires. The oil level was fine, and it hadn't been all that long since I had changed oil. So the next possibility was the solenoid. I changed both of them. Since it was due for the timing belt, I decided to go ahead and change that too. Now, the P0300, P0301, P0303, 0305 and P1349 codes are gone. But after a day or two, the P1351 shows up. As I mentioned earlier, I took the timing belt covers off and checked the belt and alignment marks. All was perfect. I cleared the code. Within a few minutes of driving the code comes back. I checked the belt alignment again. Not loose, and marks line up perfectly. The car runs smooth as can be. I do notice that there is valve clatter on Bank 2. It sounds kind of like a diesel. But it is running smooth. It is also interesting that the original valve timing problem was on Bank 1, but the valve timing problem now is Bank 2. I have only driven it a few miles since the belt change. That's all it took for the code to come up.
View 14 Replies
2002 galant 4cly overheating! So my Galant has 120k miles and I just had the timing belt replaced and I thought I'd be good and have the water pump replaced as well. When I got it back I made a few short trips with it and it was running fine then I took a longer trip about 30 miles and I noticed it was overheating, so I took it back to the shop they thought it was air in the cooling system so they preformed a few flushes, replaced the thermostat even though it was new and then replaced the pump again and the radiator cap, the radiator it's self was replaced maybe 1-2k miles ago. I don't believe the head is leaking since I'm not losing coolant and the oil isn't milky.....I'm at a loss, could the thermostat be the problem? Do I need one from the dealer? Is there a history with replacement pumps bad?
View 12 Replies
I had the Timing belt, roller, tensioner, belts, etc replaced and I am getting this funny ticking noise after the engine tuns on. It seems to go away after the engine warms up but not all the time. I have the AWM engine and bought the kit from ECS tuning. My mechanic (who is excellent and beyond honest) thinks that I have sludge in the engine. The engine was super quiet before the whole kit was replaced so I doubt that all of a sudden the sludge, if present, would cause this. I have been meticulous with oil changes and always used the appropriate weight and type. Castol Syntec 502. My mechanic told me that the belts and everything looked in great shape at 89000 miles. I wonder if I should have bought OEM parts. Otherwise the car runs perfectly.
View 1 Replies
I just installed a new timing belt, balance belt, idler, and both tensioner pulleys but am getting a little whine. I adjusted the balance belt but the noise does not change. No other belts or items are hooked up yet this was a dry run. Car seems to run fine and idles well. The hydraulic unit seems to be working fine and it's a OEM Hyundai piece.
Anything common I can look for that should stand out? 2002 Santa Fe 2.4L
View 6 Replies
Is there a "how to" on adjusting the tension of the timing belt in a 2002 accent 1.5L ....
View 1 Replies
I think I made a bad decision. Almost a year ago, I purchased my used Odyssey. I cannot remember if the timing belt had been changed. My check engine light came on, and the mechanic I took it to indicated it was the seal on the gas cap. He proceeded to tell me that I have an oil leak coming from the oil pump and that I should replace it and while I'm in there, I should replace the timing belt. There were a myriad of other things wrong with it, including broken engine mounts (which I can get fixed elsewhere from the man I purchased the car from) and some other things he said I can spread out and are basic maintenance, but I said to go forward with the oil pump and timing belt.
View 6 Replies
My car recently had its timing belt changed, it's got about 83k miles. up until then there had been some oil loss, but there was some leaking found around the valve covers so the gaskets were done. my mechanic did a full tb change, including the water pump. he said that the coolant was pretty cloudy when he changed it too.
When I got the car back, the coolant filled the tank to about half. it was running and warmed up (had just been driven about an hour) at the time. this was a couple weeks ago. i haven't driven the car since then as its my wife's ride. today, after i got to work (hour on the highway) and turned the car off, i checked the coolant level. it was at the min line.
Now of course, my first thought is "oh crap, am i really gonna have to do a head gasket now?" But I'm wondering what else might be going on, particularly after a TB change. Also, the car has been running kind of like crap as of late. I changed out the spark plugs, which were clearly OEM, and that worked immensely, but after a ride on the highway for an hour it's a bit rough getting off the highway. Dunno if it's related - my mechanic also thinks i need to replace my wires too, so perhaps it's just that.
So far it doesn't look like my oil is being consumed, though i need to pay more careful attention to that as the days go on. i do get a burning coolant (i think. could be oil, but I'm pretty sure it's coolant) smell from the vents when i warm start the car and turn on the heat. it goes away in about a minute or so. when i first got the car back, my mechanic said it was due to the coolant he spilled all over the engine, but after two weeks i wonder if it isn't something else. i suppose it could be, but the car's been driven about 400 miles since and i would think it would be gone by now. maybe i need to clean the engine to be sure? So, questions:
1) Is it possible that there was some air in the system, and that the air worked its way out, causing the overall level to go down?
2) Are there any likely areas of the TB job that could cause this? i don't recall it ever consuming coolant before, and at this rate, i certainly would have, i should think - we had the car for a year before this.
3) The car had a bit of sludging in it - guess is that it never had anything but dino oil before. So I changed it out with some 502 rated oil and my mechanic advised me to drive it hard every so often and then change it out before my normal interval. today i put it into manual mode and got my rpms up around 6000. could the high rpms have led to consumption in some way?
At this point i'd like to collect as much info as i can about this before making any decisions about how to proceed.
View 2 Replies
