Camry :: 2002 SE 2.4l / Low Idle And Stalls Out - Replaced Battery?
Dec 16, 2013
today I replaced the battery on our 2002 Camry SE 2.4l because it was incredibly slow to crank today...but it did crank. So i get a Duralast Gold to replace a Toyota TrueStart battery, and it started up fine. However, it was idling at 200-400 RPMs, so its already not right. So I drive it a quick mile or so, and when letting off the gas the RPMs drop to 200-400 while going down the street! Coming to a stop, it really wanted to stall out. Couple stops later, it did stall out, and the Check Engine light, Battery light, and Oil light all came on. Trying to restart it it cranked, started, but then immediately died. You know when you start it the RPM needle goes high and then comes down a bit? It does that, but the needle won't stop and it just goes to 0, and throws the Check Engine, battery, and oil light. I finally got it cranked, and all 3 previously mentioned lights are off when its running. It has done it one other time about 3 months ago when I disconnected the negative battery terminal for some work, and it did the same exact thing. It ended up just fixing itself, but obviously not since its rough starting and the problem came back the next time I disconnected the battery.
View 14 Replies
Advertisement
Just got the battery replaced on my v6 Camry, had no problems before it. After replacing the battery, I drove about a mile to another stop and parked the car. Noticed it vibrating and the idles very low. I restarted the car and it wouldn't stay on. Car will turn on fine, RPMs will go a bit above 1k and drop down and turn off in about 5 seconds.
Today morning I started it and it seemed fine (cold start). Idles were about 1K on a cold start. Drove around about a mile and came home and the car stalled. Same as above, it'll start up and stall within 5 seconds.
I took it for a drive (about 25 miles) so the car can re-learn everything and took a stop at Autozone. Same thing there. Didn't stall on the way because I didn't have to stop, I was on the highway. One of the sales guys looked at the car and told me to try out a new MAF Sensor. Installed a new sensor and the car died off again within 5 seconds. Checked the readings of the MAF sensor (old and new) and they both read fine.
Brought the car back home (about 35 miles total driving after battery replacement) and it'll still stall as soon as you stop. To keep it going, you have to hold the brake and hit the accelerator very lightly to keep the idle in the middle of 0 and 1 or shift into Neutral and do the same.
No CELs on the car, car drove perfectly fine before the new battery. New battery tests good, even went to the extent of putting my old battery back in (Drove about 35 miles on new battery, replaced and drove 35ish miles). Car has just short of 100k miles. Regular services are done at Toyota at about 5-6k.
View 12 Replies
My wife has a 2002 Camry V6 SE with about 75k miles. Over the past 6 months the car has developed a problem. Every so often, say once every 2-3 weeks the car will start fine, but after driving for about 5-10 minutes, will start running rough and stall if I stop for a light. It will start again, (with a little effort) and will stall again at the next stop and so on. I can pull off the road, wait 10 minutes and the car will then run like a Swiss watch until the next episode.
I have taken the car to a respected mechanic and he sees nothing obvious wrong and there is no record in the car's computer of any problem. The last time this happened the car had been on the road for about 20 minutes before the stalling problem occurred. I kept the car going at idle by putting in neutral and increasing the throttle.
After we arrived home, the car cut out when we made it into the garage but a rotten egg-like smell was in the air in the garage. After about an hour, the car stated immediately and ran like a top. That was about a week ago and no problems since. I have read in the threads about EGRs Throttle bodies etc.
View 4 Replies
2002 Camry 4 cly was running great. All the sudden looses power, stalls (won't idle), engine light came on, when I held gas pedal at 1000 rpm engine rev's 1000 - 1400 rpm. Autozone trouble codes P0300, P0301, P0302, P0171, P0420. Car barely runs, getting worse quickly. I also smelled hot metal when I pulled into driveway, exhaust tail pipe was superhot.
View 7 Replies
Just got 2005 screw fx4. Seemed to run ok 115000 mi.Had exhaust leak,I put on 3" cat back on. Then I noticed tapping at front of the engine.Turns out tim. chain guides are broken. looks like very common prob after reading many forum/threads. Anyway got timing chain kit, phasers, selinoids. Truck runs and sounds great.But so far had truck back 2weeks stalled 2x at idle.What next??
View 14 Replies
I've got a 2002 Passat 4cyl whose battery has been replaced twice in a month and died again today. I drove it for 30 minutes yesterday and found it dead about 24 hours later. Putting an ammeter in series with the ground cable, I only see a 10-20 milliamp draw with the car closed and locked. With the car running, I see 14 volts across the battery terminals, so I'm assuming the alternator is working.
View 5 Replies
2005 Toyota Prius, 85,000 miles on the car. Recently changed spark plugs with stock NGK plugs. I replaced the 12 volt battery today because the old 12 volt battery was reading 9.6 volts with engine shut off. 13.8 volts with car powered up. Long story short.
Easy swap. I have lots of tools and I am a service technician in a Bridgestone/Firestone tire factory. I can work on most anything with no problems.
The car now idles at 1640 RPM as read on my scangaugeII. I have not plugged in my Auto Ingenuity program yet but there are no trouble codes that the scangauge can read. My airbag light is on but it was on before I changed the battery. My left Side airbag is unplugged or partially unplugged and I need to search for the plug. Any fix or some way for the car to relearn the proper idle? I also noticed that my Drivers side window Auto up and Auto down feature stopped working. I can read individual sensors with Auto Ingenuity if you need numbers.
The 12 volt battery now reads 12.6 volts with the car powered down.
View 19 Replies
I have a 2002 Toyota sienna XLE, 95k miles. A few weeks ago I replaced the battery with a DieHard. Immediately after this, the right sliding door stopped working. A few days later the left side stopped working. Neither sliding door works in the manual mode, child proof feature is disabled. Fuses are good. Both doors click when any associated switch is activated but don't open. It was suggested by an owner of an older Sienna that the auto door computer needed resetting. Worth a try. His procedure involved disconnecting the negative side of the battery, waiting 3-5 minutes, reconnecting battery, use the key fob remote to open a door and then close it using the fob. Wait 10 seconds open and close same as before, doing this a total of 3 times. It didn't work, door clicks won't open. Tried again same results. This makes sense and my thinking goes that perhaps the sequence is different for a newer model.
View 1 Replies
I just bought a '12 Camry SE I4 about 6 months ago. It stalls at first startup after disconnecting and reconnecting the battery. After the first start and stall it will start normally. A pending code will come up P1604 'Startability Malfunction.' The code doesn't have a real definition other than the engine failed to start. It has a new AGM battery, serpentine belt, and the alternator passed a bench test. Had this problem with the 2.5L I4 or the 3.5L V6? Is this normal?
View 8 Replies
Last week, I brought my 2002 Ford Focus (automatic transmission) to the mechanic to have an oil change and to have the motor mounts and cabin air filter replaced. Before I brought the car in, it was fairly loud at idle--which had been going on for a couple of years and which I attributed to the worn motor mounts--but had otherwise been running fine.
When I went to pick it up after the repairs, the car would not start. The mechanic ran some tests and told me that the alternator was overcharging the battery. The battery could no longer hold a charge, so both the alternator and the battery needed to be replaced, which the mechanic did.
I thought at first that everything was OK after the battery and alternator replacement. Because I almost always turn my car off immediately after putting it in park, I didn't realize what was happening and that it was a problem... but in retrospect, I realize that ever since I got the car back from this second set of repairs, the battery light has flashed on during the split second between when I shift to park and when I turn the ignition off.
Yesterday, I took my car back to the mechanic because it stalled when I was in the parking lot at work. (I realize now that it must have happened just after I shifted gears, probably into park.) Since that was the first time it had actually properly stalled--rather than just a quick battery light flash just before I turned the car off--I had not yet made the connection between the stalling and the shifting to park, so all I told the mechanic is that it stalled on me when I was slowing to a stop. I'm pretty sure the first time it stalled was the first time I let it idle for more than a half-second in park before turning off the ignition.
He kept my car for a full day and ran a lot of tests on it. He was unable to make the car stall during multiple test drives (though, to be fair, I hadn't told him that the trigger for making it stall was shifting to park because I didn't realize it myself yet). There were no engine codes, the check engine light was never on, the fuel pressure is OK, and the throttle body position sensor, the idle air control valve, the ignition system, and the fuel system were giving no abnormal readings. When I asked, he told me that they did perform an idle-relearn procedure after replacing the battery and alternator. He returned the car to me and told me to come back if it stalled again.
Tonight, when I got the car home, it started to die immediately when I put it into park (the headlights dimmed and the battery light came on). I was able to reproduce this a second time as well. Fortunately, it does start back up just fine.
I plan to take the car in for repairs again, but I'm wondering if I should go back to the same mechanic. My questions are:
1) What is likely to be causing the problem?
2) Is it something that is likely to have been caused by incompetence when installing the new battery and alternator or doing other repairs, or could it be a coincidence (I was willing to believe the first coincidence of the battery and alternator dying while the car was at the repair shop, but I'm having difficulty believing a second coincidence)?
3) Whether or not the problem is likely to be the mechanic's fault, is it something that a thorough check on their part should have discovered?
View 4 Replies
My camry isn't starting and I thought it was the battery (5 yrs old) and got a new battery. After that, starting was difficult and it still wouldn't start. After a few aaa calls and realizing hitting the starter would get the car to start, I realized it might be the starter. Now, the car won't start even after having one person hit the starter while I turn the key.
View 14 Replies
Since having dealer work on my brakes: replaced booster and brake light switch. While at the deal the changed all the fluids. Now my EX has been intermittently stalling when stopped in drive with AC running. When it stalled the OD light was flashing. Now we have noticed that the EX is sputtering when stopped while in drive and may stall. Also, itermittently seeing the the ABS light come on. Today it stalled and now the CEL is ON.
View 14 Replies
Yesterday I drove 15 minutes to a store and came out after 15 minutes. With no previous problems, I put the key in the ignition and there was no power at all. I checked the battery and it appeared ok. I opened the fuse box, not really knowing what I was looking for, and it looked dirty with no obvious signs of something wrong, I think. About 5 minutes later the car's power came back on but once started it idled very low and died. I tried it again and kept giving it gas and it kept idleing low and would shut off. I made it home without having to stop the car at all, meaning made all lights and no stop signs, I didnt run anything. At home I turned the car off and back on and everything ran fine. Car idled normally, would start up every time, and I drove around the block without incident. I've read information in the forum about the low idle and stall but didnt see anything that referenced the complete lack of power before the idle problem started.
2002 Toyota Camry LE, 128,000 miles.
View 4 Replies
I have a 07 Camry XLE. My previous battery started dying on me so I changed to an Optima Yellowtop battery. Next day the check engine light came on, and sometimes while idle the car starts stalling, it never turns off though just that the RPM goes really low and the acceleration is really slow and it feels like the car is having trouble accelerating. Today it happened again but I was over 60MPH and hitting the gas pedal and it seemed to stop accelerating a few times.
View 2 Replies
I have a 2002 Camry LE V6 which I bought a month ago from its original owner. It has 140k miles on it. Timming belt and water pump were changed at 90k, car is in very good shape, clean engine.
It has a weird issue.
In the early morning, from my house to work around 7am, I have to drive around 20 mins on freeway , I exit and drive for another 5 mins on local street which is up and downhill, at red light or when I have to turn, the car begins to hesitate like hiccup and stall on me. The car cannot start again immediately, all power is still working, the car is trying its best to turn over but it fails. However after I wait couple mins, I can restart the car. Then, the car will run just fine, absolutely fine the rest of the day.
The weird thing here is, on days I don't have to work, I start to drive it at around 10am when it's warmer and there's sunshine, and not up and downhill, it never hesitates or stalls. Even I try to drive it up a big hill near my house at noon, nothing happens. So I'm not sure if driving up and downhill playing a part in this problem.
It doesn't happen all the time when I have to drive to work in early morning, up and downhill, but more than often. The car drives great on freeway, idle excellent around 500-600 RPM. One more detail, the gas pedal kind of vibrates (very small vibration) around 1600 RPM, and it's annoying. I'm not sure if it is relating to the issue.
Here what I did to the car:
1. Clean throttle body.
2. Clean Mass Airflow Sensor. Didn't work. Then I replaced it with a used OEM one.
3. Put Techron Additive in the gas tank.
4. Replace Air Filter.
None of the above works, but I think somehow it improves a tiny little bit.
View 14 Replies
So the wife's 02 Camry (I4/ auto) would not start for her & so I started the usual trouble shooting, fuel, spark, combustion, etc. Scan tool found 5 codes p0300 thru p0304, found the plugs to be soaked and not looking so hot in general (replaced plugs, it was time/105k). Now I can start the car but only if I hold throttle open, so when it starts if I let off it stalls, unless I hold it at 2500 rpms for 2 to 3 minutes, the car then will hold idle. If I try to mat the pedal to the flr it falls on it's face (nearly stalls, in gear or park). If I ease into the pedal the car runs without any issues, can stroll down the highway 70/80 mph with cruies or pedal. Currently no codes but will not take fast acceleration. If the car sits for any amount of time I have to hold throttle open to start it/ large cloud of smoke, smells liek raw fuel. Cleaned MAF, throttle body, etc...
View 5 Replies
Own a 2002 Camry 4 cyl with 186K, like it soooo much ,once a day I get something like a missed shift around 20 mph .
I notice that over 65 mph, the RPM's are higher than my other Camry: 65 mph 2450 RPM instead of 2300. 70 RPM 2700 RPM instead of 2450. 75 MPH 2900 RPM instead of 2700.
At 80 MPH drifts between 3000 - 3200 RPM instead of 2800. When idling in park, I heard a whining noise coming from the Trans. I was told it recently had the engine replaced.
View 10 Replies
I have a 2002 camry that stalls out while driving. The car stalls when engine is warmed up and the car is running at appropriate temperature. When this occurs no "check engine lights" stay on and the car re-starts after 15-20 minutes and runs just fine. I had the car looked at by a Toyota dealer and another independent shop and they where unable to pull any codes from the computer module. The car is up to schedule with routine maintenance items. The car is garage kept and I go to the same gas station each fill up.
View 2 Replies
I changed my dogbone mount over the weekend. Did not get a oem but got one from advance auto for 50 bucks. So I noticed a vibration when I'm in reverse or drive. I got some vids of the engine running. Could the cheap mount I got just be causing more vibration than the old one?? Which was cracked?
[URL].....
View 14 Replies
I had water pump and belt changed by a Toyota Dealer on 2006 4 cyl Camry LE. Now the car idles a little rougher, gas mileage is down by around 20%, and there is some subtle chatter noise.
Before the car would idle quiet (could not hear it from inside car), now it is noisier with a little vibration- both in park and drive. Gas mileage is worse, and I am compensating for winter temps (no snow around). I fill the tank and reset mileage to check. The needle also confirms lower mileage too.
A little noise around belt or pump area but another mechanic said belt tentioner is fine, no need to replace. So what could the dealer have done to cause this? What parts/systems do they operate on? Dealer said car sounds o.k., can't hear anything unusual (of course).Is there anything I can check myself or fix myself? I may try an auto stethoscope when I get one. Just want the old car back. Car has timing chain, no belt.
View 9 Replies
I drive a 2002 Toyota Camry. Mostly runs great! If I drive on the freeway at 60-70 mph for 30-45 minutes, when I get off on surface streets the engine starts to die. I have to keep one foot on the brake and one foot on the accelerator to keep the engine >1000rpm. When I park at my destination and park the car for 1-2 hours, everything is fine when I start up again. Happens repeatedly - not always, maybe 95% of the time. Two mechanics can't figure it out and are unable to reproduce the problem after they drive the car on the freeway.
View 4 Replies
