Camry :: 2002 LE - Oil Light And CEL On After Valve Cover Changed
Jul 25, 2015
I changed my leaky valve cover gasket today, along with my spark plugs and PCV valve. Now after driving a few minutes my CEL and oil light come on.
the car was/is low on oil from the leak. I was going to change the oil but it has been pouring rain today and it was all I could do to get the valve cover gasket done.
I put two quarts in after the oil light came on, I haven't had a chance to check the level since then.
I don't see oil leaking anywhere on the engine. I cleaned it up pretty well around the valve cover and should see any new oil easily.
How low does it have to be for the oil light to come on?
View 1 Replies
Advertisement
I have a 2002 toyota camry xle 6 cyl i believe i have a valve cover gasket leaking vehicle has 112,000 miles. is there a step by step removal proccess i can access. I have done one on a 1995 honda passport 6 cyl how difficult is it
View 2 Replies
2002 Camry 4 cyl was leaking a small bit of oil on the rear passenger side of the valve cover - about directly behind where the timing chain is. I replaced the valve cover today, but noticed that there is still a small amount of oil leaking at the same spot. Is this a common problem with the '02 Camry? Or perhaps I have a valve cover problem?
View 2 Replies
I was loosening the bolt that holds down the number one spark plug wire when it just spun off leaving less than half the bolt in the valve cover. I tried using the grabbit extractor but that did not work.
View 8 Replies
How to replace valve cover gaskets on 2002 430sc???
View 14 Replies
Replaced this gasket that seems to be leaking oil. Looks simple enough, is there anything i should do or know before taking on this job? It's a 2002 Accent GS 1.5L ....
View 8 Replies
so I have a 2azfe engine
So there's an oil leak coming from the valve cover gasket (just purchased vehicle dirt cheap with 220k)
found this
Notice all the oil sitting on top of the exhaust mani gasket
In the left(lower) part of the picture it appears to be scraped.
the gasket appears to be newer, I did NOT use a screw driver to remove the valve cover, which is what this appears to have been done..
Can this be sanded down then filled with jb weld, and then regasketed?
View 7 Replies
So I'll be taking on a project to replace the valve cover gasket on my 2002 Camry V6. There's a bit of leakage through the gasket. And while I'm at it, I'll replace the spark plugs as well. I'm looking for a write up on this project. did a lot of searching but couldn't find anything.
View 14 Replies
2007 2.4L Camry LE.
Took the plastic engine cover off and found that there are two rubber gasket/washers that stayed stuck to the valve cover (around the threaded rods that stick out of the cover). When I tried to remove them, they disintegrated. Now, my plastic engine cover is having problems tightening on properly, if that makes sense.
So, if you look at the engine cover, you take the two nuts off and remove the cover. There are rubber isolators/gasket that is there. Mine have disintegrated. Call to the Dealership says I have to replace the entire cover as you cannot get those separately.
View 1 Replies
I have a 2003 Toyota Camry with 210,000km on it. Today I popped the hood, noticed the coolant was slightly low in the over flow reservoir so I looked around the engine bay. Now I know generally coolant does not go up that far and it's just oil... But this has got my head turning. There's a crusty coolant residue drip that looks to start at the valve cover. At first I thought maybe the water pump was leaking, and the pulley was spinning it farther up, or spraying back from a rad leak when driving. but the fact it's crusty and A clear line that looks like a drip that's a slow leak and has crusted over time makes me wonder.
I mean generally coolant wouldn't come out of the valve cover unless it was right full of coolant, causing enough pressure to push it out... Am I wrong ? Once I get to the shop on Monday I'm going to pressurize the cooling system and pull the spark plugs and the valve cover to look at the head, The highest spot I see the drip start is the valve cover, only thing I could think of is the intake leaking, and traveling over there but even then, it doesn't make sense to me. The thermostat housing is about 2.5" under so it can't be that... It's such a small leak, the reservoir is only down about maybe half an inch and the oil looks clean as can be.... There's some pictures below that you can somewhat see it.
View 12 Replies
Own a 2000 Camry XLE 6-cyl. Both valve cover gaskets are leaking. Rear one leaks onto the manifold and causes stench. Have been quoted $350. to replace because the job is complicated. Have any of you done this on your own, and if so, would you recommend it or go to a qualified mechanic?
View 9 Replies
I have a a 02 jetta 1.8 turbo the code po343 came up after new temp sensor,valve cover gasket and full tune up. is it an easy fix the car is misfiring an very hard starting.
View 1 Replies
I'm looking at replacing the valve cover gaskets on my 02 f-250, it's a 7.3L.
Looking at them on line there are many different brands. What have you used on your 7.3L, and which has worked the best for you?
View 4 Replies
I have a 2002 F250 5.4with Air Conditioning. The valve covers are leaking and the gaskets need to be replaced. I am attempting the valve cover gaskets. I was able to get the drivers side cover off with some difficulty. For the passenger side valve cover. There is very little " no" room to get at the bolts. I read somewhere that I may have to drop the engine on that side. I will do that if I have to.
View 5 Replies
New valve cover gasket on my 03 VR6 GTI, new plugs, oil filter and cooler seals, new gaskets on the intake manifold and when we started it up . . . .
[URL] .....
It runs rough.
EPC light is on.
Stall at idle.
Runs great at full throttle.
View 3 Replies
I have a problem with my Toyota Camry 2002 4 cyl. 2.4L, I changed my Motor cooling fan but my car keeps overheating, I changed the overflow tank top, but still its overheating and the car turns off by itself sometimes, when its cold (after i turn it on) it starts bucking and also if its stop (example, if i park somewhere), and at last, the temp isn't showing correctly on my dashboard.
View 2 Replies
I bought the little car to get off my motorcycle and its done great. But, after a couple trips around town my check engine light came on, and I imiditely noticed a change in my idle and engine performance. Im assuming my engine changed the air/fuel ratio to account for the sensor indications. My initial code read came back with four codes which said something about spark, and O2 sensor, and emissions. I went ahead put new spark plugs, gaped them as well as replaced the first O2 sensor.
After that I reconnected my battery and sure enough no engine light and my idle felt even better than before. (by the way my old plugs looked normal) But shortly down the road the light came on again. My idle did become a little different but not like my first encounter with the engine light. My power too seems a bit degraded, as well as the engine's sound. As of right now I am only reading one code P0422, which I do not see in the manual. I read online that its probably my catalytic converter or my engine is running at an improper air/fuel ratio. I am praying that it is not my catalytic converter and just my engine computer throwing things off.
Other things which may serve as clues:
Slight valve cover gasket leak (I will change the gasket when I do my timing belt job along with other seal and probably the water pump)
When pumping gas I can get about 90 cents in at a time, now more like 40 cents since the Saudis lowered our gas prices. Assuming I've got some kind of venting problem.
Car has 107K manual shift.
View 9 Replies
I have the 2002 V6 camry and I want to replace the PVC valve. I read through the FYI/stickies, and I can see exactly how to do it on the 4 cylinder engine, are there any instructions for the 6 cylinder engine, I just want to make sure I do the right thing?
View 14 Replies
2007 Sonata GLS 2.4 liter, 145,000 mostly-highway miles.I have a P2187 OBD code, which means an upstream O2 sensor. It's on order, should be arriving in a few days. The sensor has been bad for about a month, but I just recently ordered it.BUT... now I have a fairly loud valve tap; this is tapping whether the engine is cold or hot. A few weeks ago I changed my oil; put in hi-mileage oil (Pennzoil maybe? I remember it was a gold container) and a Fram oil filter (I noticed a number of people on here saying to definitely not use Fram).
I checked the codes again (I was thinking maybe a camshaft position sensor) but I still only have the P2187.This model has a chain, not a belt. So a few questions: Could having a bad O2 sensor (and hence running lean) have caused the tapping?I was thinking of doing an engine flush, then putting in some Lucas along w/synthetic and a new filter.
View 2 Replies
I have a 06 Elantra having a problem with a p0441 code flow fault I changed purge valve and canister purge valve I don't know what else to do what else can I do to get it to go away permanent so I can get car inspected no codes for my car can be on but only 1 i/m
View 3 Replies
I had it checked out at the dealer and they called it a "weep" so they went on to tell me that VW probably wont approve warranty work for it. I pushed for them to take pictures and send it in anyway.
Now assuming they won't do it, I have been looking for a DIY or a technical order on the job but I can't find anything.
View 7 Replies
