Camry :: 2002 / 2.4L Ignition Coil Failure
Nov 21, 2011
I have a 2002 Camry 2.4L, ECM 89666-06220, ignition coil 90919-02243. One of the coils has gone out. I got a misfire code on P303. I then moved the cylinder 3 coil to cylinder 4, cleared the code and restarted the car. The new code was P304, bad coil. I found a set of low mileage used coils, 90080-19023. The dealer says this number was one of the three options for 2002. But the pin-to-pin ohm values don't match.
The 90080-19023 pin ohms, 1-2= 348, 1-3=667, 1-4= 490, 2-3= 1100, 2-4= 912, 3-4= open. The 90919-02243 pin ohms, 1-2= 390, 1-3= 673, 1-4=940, 2-3= 1154, 2-4=1403, 3-4= open. How to successfully do this substitution and not burned up ECM ?
View 1 Replies
Advertisement
Just a few weeks ago I replaced a bad ignition coil because I got the engine code P0302. I replaced the spark plugs with NGK Laser Iridium and the second Ignition coil. Now a few weeks later the Ignition coil 1 has died on me.
View 1 Replies
I'm getting Codes: P0300-306 (Misfires) and P0356.
I have researched the definitions of these codes and see that P0356 indicates an ignition coil failure on coil "F" (which would be Cylinder 6?)... but how is it possible only one coil is failing but I'm getting multiple/random misfires on all cylinders?
I've looked at the wiring diagrams and the only place that I can see a "single point failure" that can cause such a thing, would be the ECM itself...
View 14 Replies
We bought it in 2010, since then we have replaced 5 ignition coils and 2-3 batteries. Everytime the car acts up, the VSC and traction lights come on and the car starts stumbling and hesitating. The car eventually dies within a few minutes. Pull up codes and its always been an ignition coil.
Well we had all of these covered under warranty until the warranty expired in Aug. A month ago this happened again, and thought the battery was dead. It ended up being #4 coil, so I replaced.
My wife drove last week and lights came on and lights started going on/off and dinging at her and the car died. I jumped it to get it home, turned off the car and was dead. Voltage at battery was 9 volts.
I charged overnight and started the next day. I pulled negative battery cable w car running to check alternator and it stayed running, so that's good. The car is now starting just fine again.....until this happens again.....which it will.
My question is what in the heck can be making all of the coils go bad and why is the car intermittently throwing warning lights and just dying? This last time the codes pulled we P0345, PO365, PO390. All of which I don't see an explanation for.
View 5 Replies
Any easy solution to reseating this wire in the connector? It got yanked out by accident when i was removing an ignition coil under the wiring harness. 2007 camry v6
View 3 Replies
I replaced my valve cover gasket yesterday on my 2004 Camry. While putting back together, three of the tabs on the connectors for the ignition coil harness snapped off and would not stay together because of tension on the harness. I tried to zip tie them because I read that in another forum post but the clips (alligator clips?) inside the connector did not seem to be making contact with connector on top of ignition coil. The car was mis-firing and running very rough.
After much frustration, I finally removed the wires with the alligator clips from inside the connector and plugged them directly into the top of the ignition coil. Well, the car started and seems to be running/idling fine although now the Check Engine Light is on. Also, I have not driven car yet.
My question: Can I drive the car like this or will the vibration from the engine eventually loosen the connections. I am planning on ordering the connectors but they will not be in for a few days and I need to drive the car.
View 1 Replies
I bought 2002 3.0L Solara with some issues, one of being a miss fire. What should the resistance be, and which terminals should I be using?
View 1 Replies
I have come to understand that Buick LeSabres are known for their issues with their ignition modules but I'm trying to figure out the root to the problem. I have an '04 LeSabre 'Custom'. I have had all of the coils and wires replaced and the ignition module. I had to replace some of the coils and ignition module twice since. I can already feel it going again.
View 6 Replies
I'm driving down the road yesterday, and going through a intersection, get through it i'm in 3rd gear, 20mph, and my car starts to misfire, so i am like crap coil pack, i changed them all with new plugs maybe 1000 miles ago. Well I slow down so i can turn around and head back to my place slowly a mile away. and it never happens again. Now the car had just had the complete exhaust replaced last week, and literally only 9 miles put on the car before this happened. I drove 35 miles to work today, and roughly 50 miles last night after this and it has not happened anymore. Am i doomed for coil pack failure again?
View 6 Replies
1.8 had recent coil pack problems? I recently had a coil pack fail in very hot weather 2 weeks ago. This week during another heat wave I believe the coil was again causing the engine to start missing. I know about VW's past reliability problems concerning coil packs and am now concerned that this may be surfacing again.
View 8 Replies
Camry 2002 XLE 4Cyl. 2.4 ... When I switch ignition key on, there are no ABS and Brake light come on. Why is that happening? How to fix it? Normally, when we switch ignition key on, what are indicator light on?
View 6 Replies
My steering wheel and ignition locked up 2 days ago. I tried turning the wheel and the ignition at the same time, tried the brakes, tried shifting gears and anything else i could think of. I think the problem might be with the ignition coils, or multiple ones, but i have bypassed that by hot-wiring the car(which was a pain because of all the anti-theft features).
So I have the car running now and it is almost drivable except the steering wheel is locked up. I need to know how to fix this, i have read plenty on it and i think i can break a pin that locks the steering wheel to make it work, but i don't know where this pin is(might be behind the ignitions, or attached to it somewhere). if i could do this without breaking anything that would be great, but if the car will run, I am ok with it begin broken, because i already hot-wired it so I'm not worried about breaking anything unless it will make the car not run.
View 4 Replies
I have a 1991 Volvo 940 SE with turbo and 162,000 miles
The problem is there is no spark coming from the ignition coil. There is power going to the ignition coil but no spark. The car turns over but doesn't start.
I have replaced the crankshaft sensor and the Ignition Module. The wire that goes from the ignition module to the Ignition Coil has been replaced with a new wire that goes directly from the module to the coil .
Also the coil has been checked and its operating within parameters.
View 16 Replies
Understanding all the needed parts when replacing ignition coils on a honda fit 2007. My understanding is it is best to replace all 4 (are there 4 total?) as well as the spark plugs - also 4?What other parts are needed, does this car require spark plug wires?
Basically, Would this be a good time to replace air filters as well? Car has 116K miles.
View 18 Replies
Found out today that my third ignition coil is bad, it's a Honda civic 03' my question is, do I have to buy a new ignition coil. I had a clerk tell me I could switch the coils and it would run fine? Is this right? could I just switch the ignition coil with another ignition coil? This doesn't sound right. Well If I do buy new one which would be the third ignition coil? is it counted from left to right or right to left? Are there any telltale signs of a bad ignition coil on sight?
View 16 Replies
Ignition coils on Hyundai Accent (2011) getting stuck in suction? Or looking for engine vacuum pathway explanation?
I previously (~6 months ago) replaced one ignition coil that had a misfire. I currently have a check engine light with "No Codes" on code reader. My engine is rough idling with very weak acceleration. This occurred when trying to accelerate up a hill. I was looking to inspect the coil resistance and noticed the replaced coil has a pretty strong suction holding it in.
View 13 Replies
2000 Honda Accord. I've been told I have a bad ignition coil. Do I need to replace all six or can I just replace the one?
View 19 Replies
I have a 2007 RX 350 2WD. Recently, the check engine light is on, as well we two other lights are on as well: VSC, TRAC OFF.
I went to Lexus and was told that the error code is P0356. I was told that the ignition coil F is problematic and need replaced. I was quoted 1 and 1/2 hours two 2 hours work and need $412 for the repair. Well, I went to auto zone and was told that No 2, 4, 6 ignition coils were on outside so that it would only take about 5 minutes to replace the problematic one with a new one.
I did the replacement indeed by myself after buying a new ignition coil. Initially it was fine and the light went off after a little while. However, after about 10 days, those three lights went back again. I check the ignition coil, it seems fine and I was told that it is very unlikely for a new ignition coil to go bad this quickly.
I was told that I may need to check my spark plug as well. BTW, when I start the car, the car is a little bit shaky.
View 14 Replies
I have a 1995, 1500, 350eng, PU. there seems to be an electrical problem in the ignition system. when the key is turned on the check engine and other lights do not come on and there is no power to the coil/ignition. When the lights do come on the truck starts. I have replaced module, dist,pickup coil, coil, cap and rotor. Could the problem be in the computer?
View 1 Replies
I have a 2003 passat 1.8 and I just started having a misfiring problem. I googled it and ran across a 2003 press release that VW had recalled them. I am going to call tomorrow, but I did a little testing myself. Probably not the best thing to do, but this is what I did. I had my wife start the car and I pulled off the coils until I hit the one that didn't make the car shake any more than it already was. It is the second one from the front. I pulled the spark plug out. It is the original, but didn't look too bad.
My question is: How do you test the ignition coil to see if it is faulty or if it could be the distributor? The coil that attaches to the plug looks a little burnt around the rim where it connects to the plug. Its not an expensive part, but I don't want to go buying another one just to find out it is the main distributor or something else...
View 3 Replies
How to remove the clip on ignition coil connector wires that attach to all 4 of the coils.
I see that it has a black tab that you pull to the up or out position. From there I'm at a loss what to do. I managed to prode and poke and got one off, but I nearly pulled the connector off the wire and I know I didn't do it right.
Is there a simple way to release these mothers that I'm just not getting? If so, looking for explicit instructions in minute detail..
View 6 Replies
