Is there a safe way to remove rust from a cooling system? It's on a 1950 cadillac that's all cast iron with a copper radiator. I'm pretty certain the coolant passages in the engine are plugged up from rust. I took off the rad hoses and rinsed everything out until it ran clear, but I've done this before and the car still runs hot.
View 1 RepliesI'm going to be freshening up my distributor for my 1950 Cadillac, and I think because of bad weather stripping and other leaks, when it rains heavy, moisture might be getting on the distributor. Is there something I can spray on it that will repel moisture or would just a healthy dose of dielectric grease do the trick?
View 12 Replies1950 cadillac - standard drums on all 4 corners.
I put new wheel cylinders on each drum, and replaced the drivers front hose, as it was clogged. The passenger side I left because it works and doesnt leak. I've cleaned all the brake surfaces, shoes and drums, and bled everything.
When I brake, and only when I brake, the front right makes a grinding noise and the car pulls to the right.
I tried tightening the star wheel today to bring the shoes inward in hopes that would equalize brake pressure up front, but when trying again today, I got that grinding sound still.
There is no scoring or gouges on the shoes, drum, and the inner and outer ball bearings seem fine - round chrome balls with no discoloration, no gouges on the spindles. Granted I don't drive this far at all, especially now that I have this grinding.
How can I really tell if its the ball bearings? It only makes the grind when I am on the brakes.
So i've been searching for ways to remove the bumper/door chrome trim to change to black but cannot find anything about the b5 or 5.5. What i'm trying to do is get the chrome to black but cannot figure out a safe way to remove them to either wrap in black vinyl, paint or just replace with black strips. I'm not trying to completely remove them just get the chrome to black. Its an 03
View 10 RepliesTwo weeks ago a large, industrial truck dropped a piece of bent steel pipe on the interstate in front of my 2010, 50k miles, Prius and (sadly) I was forced to hit or swerve into rush hour traffic and cause an accident. It tore up a good part of the cooling system and did some body damage. Of course I didn't know this at the time, but it began to overheat, so I pulled off the freeway and had it towed to a body shop. After about ten days, I got my Prius back.
View 13 RepliesIs it possible to use so much coolant system stop leak that you could clog the transmission cooling system?The fluid is burned and seems like I am having problems with gear shifting and power from the transmission. 2003 Olds Silhouette...
View 1 RepliesNew 2015 PIP, got it 2 months ago, and it drove fine till Thursday, when this message came up. I believe I first got a "Charge interrupted due to malfunction" and then the dreaded "Check Hybrid System, Stop the vehicle in a safe place." alert with all the engine lights on.
Took it to the dealer and they charge it up, cleared the message, and gave it back. They told me it was because I shared the car's outlet with something else, and then threatened to charge me money if I came back because it was my fault. Took it home, charged it exactly the way they told me to, and this morning the error message came back up. Going to take it in to the dealer tomorrow.
How accurate are electronic tire pressure monitoring systems? My dashboard digital readout usually reflects 3 or more pounds less than psi taken with various manual gauges (cheapo, expensive, digital). Which should I believe?
View 5 RepliesI have come across reading about all the issues 2006 AWD models have, and one in particular is the exhaust system. It lacks a proper replacement. After reading about people's exhaust system leaking having rust through out, I decided to take a look at mine. It is full of rust.
View 9 RepliesI have a 2003 Escalade that I have maintained since day 1. Occasionally when driving the car it will say system disability and reduced engine power, which drops the speed to 20 and I can give all the gas I want it will not go. Happening on and off for 5 months. I can shut it on and off a couple times and it will go back to normal. Have taken it in a couple times to dealer and they have drove it and drove it and it behaves. They believe it is the Throttle body and sensor. But for the price of it, just replace the fuel pump 2 weeks ago, they suggest to see it happening to give me a 100% diagnosis. For now they believe it is that. Should I fix it or wait till it happens and slowly putt into the dealership.
View 4 RepliesI thought these things were bullet proof. I have 2 sets of recently installed ceramic coated headers and both sets are getting a rusty haze to them. One is a set of cast iron manifolds I got done at Jet-Hot and the other are from Ford Racing. Is there a polish or cleaner that will bring them back yet not damage the coating?
View 1 Replies115,000 miles, adult driven. Hard cranking, took into dealer. Replaced 4 injectors - cylinder 2 misfiring. Showed me return gas line clogged with brownish material. Dealer stymied.
Now, Subaru headquarters diagnoses replacing all steel fuel lines, fuel rails, fuel pump...full of rust from inside. Tank looks Ok, as does filler neck. Premium gas used always, added Drygas seasonally as needed.
Question: where the heck would rust come from? What can I do to prevent this problem again? Love the car...would like to get 200,000 from it.
My dealers charges $60 for this. Sounds like all they do is drain the radiator and refill with new anti-freeze. I recall when it used to mean drain the radiator, refill with clean water, run the engine, flush, and then refill with new anti-freeze. If all they do is drain the radiator and refill, I guess I can buy the anti-freeze and do it myself and save about $45. Or is there more to it than the service manager described?
View 7 RepliesSo CEL came on a few weeks ago as it does here and there so got it scanned today and it said "cooling system too lean" could it just be the mods throwing the light. car is tuned so i thought cel wasn't suppose to come on and no mods to the cooling system beside cold air intake..
View 6 RepliesMy MIL came on the other night so I brought it to the dealer today for diagnosis.
Per tech, "Found 1 DTC P2181 for cooling system malfunction, checked measuring values, found thermostat sticking open.
Recommendation is to replace thermostat with housing." I have 95K miles on the car, original owner...first time in a long time to have an issue.
The SA indicated the thermostat replacement. The tech indicated the thermostat is in the front of the engine which is hard to access.
Planning on doing a flush, but how do i bleed the air in the system after? is there a bleed bolt?
View 5 RepliesMy 2009 has been showing the CEL off and on for a few weeks. Have had it read at auto zone twice, two different codes. Both cooling system related, but not the same. Today I filled the gas tank and it went back off.
Is it possible for the cap to be causing the light, or would the scanners tell that in a code? I just hate to take it to the mechanic when it is running fine and the light is not even staying on.
Ok, a year or two ago, a small leak in our 04 GX470 prompted me to have an a/c guy recharge system (little did I know how easy it was to do). At the time, he used his blacklight (during the day) and "thought" the condenser might have a leak in it.
Fastforward to now, the system stopped cooling. There isn't any noise from the compressor and the clutch does seem to engage normally.
I went to Autozone and rented the DVD on A/C systems. Using the gauges, I found there was no pressure on the H or L sides. I replaced the condensor (a no brainer ... it even came filled with desiccant/drier though I had to return it since the condenser didn't have the plugs in place so the desiccant/drier would have likely been 'wet' already ... no problem). I noted a very slight grainy, metallic in the system, but not very significant ... I did not flush any hoses, but I did look at all visible hoses for dye stains.
I connected a vacuum pump and kept it a 30mm Hg vacuum for 30 min and rechecked it 30 min later to see that it held the vacuum. The first time, it didn't, so I rechecked my connections and repeated. It seemed to work. I charged the system with 24 oz (27-29 is capacity so I wasn't quite full) and the system was nice and cold.
Unfortunately, cool only lasted 3-1/2 days!
The original condenser plug (for the desiccant reservoir) was plastic or teflon, but the one that came with my replacement was Aluminum. A replacement desiccant bag also came with another plug (a plastic or teflon one), but it seemed to strip so I opted for the metal one anyway (besides, it had two green 'O' rings to just one 'O' ring for the plastic one.
Two days ago, I thought I'd got it to hold the vacuum in the system, recharged it again (I dried the desiccant bag in the oven for 5 hours at 175 deg F to make sure I'd gotten rid of any moisture that had developed).
Dog gone it, it's hot again! Looking at it with my black light at night, I do see dye (I'm using the yellow kind) at the L-side Schrader valve and on the plug to the desiccant compartment, but no where else. Where's the drip line for the condensate so I can check to see if there's a leak in the evaporator?
I tried wrapping some teflon tape around the metal plug for the desiccant/drier, but it still wouldn't hold a vacuum when I tried using the pump tonight.
I have another dessicant/drier bag and plug arriving tomorrow since I'm afraid that it still could just be leaking out the base of the condenser, but I'm not sure.
This morning (cold outside) I started my 2011 Golf TDI and the cooling system light started flashing.
The owners manual says to contact my dealer if this happens. I originally thought that it was because the coolant was low, but the manual states that if the coolant is low, the light will be solid.
I scanned the car with my VAG-COM and there were no related faults found.Perhaps my owners manual is wrong and it really is because the coolant was low? (that's how my mk3 was).
I have a 1997 no turbo Passat 2.0 6 cyl.Over the weekend one of the plastic pipes for the coolant system cracked and after the replacement I end up with the panel telling me that there is no coolant on the reservoir. How to bleed the air out of the system or if there is any bleeding valve for this purpose? And where is located?
View 1 RepliesI have a 2001 530i BMW experiencing an overheating problem. I replaced hoses, radiator, thermostat, water pump, alternator, both belts all of which went fine. However still loosing anti-freeze, it seems to be coming from under the intake manifold. Looking for step by step instructions on removing it to get to the problem?
View 5 Replies