C/K :: 92 K1500 Hesitation / Power Loss When Engine Warm Up
Oct 8, 2014
I have a 1992 k1500 5.0L. The pickup seems to run good, or at least better when it's cold and engine isn't to operating temp. But once it reaches temp it loses a noticeable amount of power, as well as has a "dead spot" in throttle response. From about 1/2 to 3/4 it's like nothing happens you push the pedal but no response. Only at about 3/4 once it down shifts then you get an increase in speed. So now back to power loss. It is bad enough that just to maintain a highway speed of 60mph it will downshift even on very small hills and on flat ground the pedal is about 3/4 of the way to the floor.
Some history: It has a rebuilt transmission in it with a 2000 rpm stall converter instead of stock(so two questions one when I re installed the kick down cable could I have adjusted it wrong and could this cause my issue, and what's the proper way to adjust? Second could the 2000 rpm stall converter cause any issues?)
It has a new distributor, cap, rotor, along with plugs and wires. I recently installed: knock sensor, map sensor, coolant temperature control sensor, tps sensor, egr valve, pcv valve, ecm, rebuilt the throttle body, as well as a few other things I'm probably forgetting.
I suspect the engine is running rich because the exhaust tail pipe has a lot of soot(it has no cat was that way when I bought it but it has way more soot than it should even with no cat.) I just checked fuel pressure and it's right at 11 to 12 psi. I haven't pulled plugs yet to confirm rich condition, but last time I changed them they were all black as coal.
View 6 Replies
Advertisement
I have a 06 f250 king ranch with 6.0 . A few days ago my scangauge showed a code P0405
I changed my egr and after it showed two codes : P0405 and P0404
It still has a hesitation and loss of power , although better than before the Change.
View 3 Replies
My 2001 VW Passat 1.8T manual transmission is experiencing loss of power/hesitation during acceleration. Occasionally the check engine light will blink for about 10 seconds during this time. My valve cover gasket blew about 7 months ago. I had it replaced along with 2 ignition coils. Since then I have had replaced the other 2 coils and spark plugs because of this recurring problem. I have also replace the mass airflow sensor for the second time. The diagnostic check continually shows misfires in different cylinders for which I again tried replacing the coils. I have also received the codes for "fuel mixture too lean" as well as for too rich. What could be causing this?
View 4 Replies
Once again my Celica is having a similar issue. Originally over 6 months ago i had an issue with my MAP Sensor which was causing extreme hesitation issues and the car was basically not safe to drive in traffic.
The issue that is now occurring is that i can start my car fine and drive around on flat normal roads with no issues but ive noticed once i go up a steep or decent hill/driveway the car will start to bog down around 1500-2100 RPM.
Once it starts to play up it continues to do so even on flat roads.
Have Checked:
- MAP Sensor - OK
- Distributor - OK
- Leads - Old but still ok, plan to replace later.
- Spark Plugs - Ok
- Spark Plug Wells - They had oil in them few weeks ago, cleaned out and hasent returned.
- Need to replace Valve cover gasket to fix this i believe.
- Fuel is ok.
View 6 Replies
I drove my car to work today and no problems. Tonight my wife and I took the car out to go to dinner and intermitantly there and back my car is hesitating as we drive along. I thought it was odd at first then my wife asked if I was kidding around. I told her its not me.
It's as if the car is driving then all of a sudden its like a loss of power or as if the limiter kicks in and starved the engine of gas and then a second later it jerks back to life and keeps going.
If it does this tomorrow its going to the dealer. It is not throwing any warning lights and I have 3/4 tank of gas so its not that.
View 17 Replies
My 2003 Camry loses power and starts to hesitate or miss-like under load, but when cruising along not under load it runs smooth. There is no check engine light coming on.
I have changed the fuel pump and fuel filter in the tank.
I have changed the spark plugs.
I have added injector cleaner and fuel treatment to the fuel.
I have cleaned the air filter and air filter compartment.
View 7 Replies
Alright, my '06 SV6 AWD has a major problem...I'm about to blow it up! But seriously, I've had an issue for a few weeks now with intermittent acceleration/hesitation problems. Basically it started as a rare occurrence and is happening more often now. Yesterday, it did it consistently for 20 minutes on one trip around town. 1 hour later, it didn't happen noticeably at all on the way home. It happens while accelerating, usually from a stop, but also sometimes when cruising at highway speeds.
The car does not stall or stumble. Everything sounds fine and smooth, but when accelerating from a stop, the car will stop accelerating and the speed slowly drops off. Pushing the accelerator down further to the floor does nothing for several seconds, then the power returns and the car responds to whatever position the pedal is in. If you haven't pushed further it continues accelerating where you left off. If you've got it to the floor, it takes off quickly. When cruising at speed, you don't notice anything until you start slowing down, and the pedal reacts the same way. NOTE: The engine does not rev up when this is happening. It's not like the tranny is slipping.
It really seems like a fuel delivery problem and not transmission. It has all the normal symptoms of a failing pump. And about 2 months ago, I had the fuse for the fuel pump melt (not blow). These problems didn't happen immediately after, but they did happen a few weeks after that.
That said, I have noticed that when cruising I occasionally hear a light clunking noise that sounds like the rear diff engaging. I assume this is just due to play in the drive train. I also had to recently do the expensive versatrack fluid flush and fill to get rid of the diff groan. But I still feel like it's probably fuel related because the engine doesn't rev up.
Here's what I've done so far:
1. Checked the wires at the problematic C305 connector. I already had to completely redo that connector several years ago as the PO had removed the connector and directly twisted all wires together covered the with tape, and filled hole with silicon. BTW, GM does sell all of those harnesses with length of wire, connectors, and heat shrink covers for reasonable $$. Anyway, found 2 wires with insulation slightly shaved off. Neither was for the fuel pump, everything else still looked good.
2. Checked voltage at the gray fuel pump wire just after the new harness (about a foot before the fuel pump). And checked the ground at the same location. Haven't checked at pump connector because I don't want to drop tank just yet. Both were fine with almost no resistance on power between that location back to the fuse box. So, it doesn't look like a bad or shorted wire unless it is in that short length up to the fuel pump that I cannot access w/o dropping the tank.
3. Checked fuel pressure at the fuel rail. The pressure when primed and idling is a consistent 60-62 psi. I know the manual states 60psi as the max. Maybe this has something to do with it?? Perhaps my cheap actron pressure guage is a bit off or perhaps the pressure regulator is bad. Could this cause the issue.
4. Checked for DTC's with code reader. No active or pending codes.
The other things I think could be the cause based on internet research:
1. Accelerator Pedal Position (APP) sensor
2. Throttle Position Sensor (TPS)
3. PCM
4. O2 sensor
The problem is that all of those things tend to set a DTC from what I've read. I still think the fuel pump us going bad and the pressure was fine because the problem is intermittent. I just don't want to spend the $$ on a new pump to find out it was something else.
Tomorrow, I will have access to a scanner that can log 10 seconds of data from the computers while driving. I think that might shed some light if I can get the problem to happen when recording. I'm not familiar with fuel trims and the lot.
View 3 Replies
Hesitation and power loss have returned. I removed all four spark plugs and found that the spark plug on the driver side of the engine, or side closest to the inverter, and its coil pack were covered in dried/sticky oil with no loose oil present around them. Pics added to new post #11 of coil pack and spark plug.
I couldn't find anything that really matched the symptoms I was having this afternoon on the way home from work. After letting the engine idle for about a minute to get through Stage 1, I pulled out of work but noticed I kept hearing a slight whining from the inverter (radio was off and windows were down) while going uphill on the road out of our parking lot. Speed was in the range of 25 to 30 MPH.
Torque showed I was pulling between 10 and 20 amps from the HV battery but what I noticed that was REALLY weird was that the timing advance gauge showed I was running around 2 to 3 degrees (?) instead of normally being around 13 or 14+ depending on how quickly I'm accelerating.
And the more acceleration I demanded, the the more amps were coming from the battery and the RPMs on the engine would go up, but the timing advance still remained below 10 degrees. I didn't hear any knocking but I could definitely feel the lack of power.
View 19 Replies
My truck - early 2000 CC short bed, 300K miles
Background on my problem: I had a short list of long overdue maintenance and updates to do that time and money kept me from tackling. Found a little of both so I replaced the water pump, HPOP lines, re O-ringed the HPOP/IPR, deleted the AIH, replaced all of the brake lines in the engine bay, put new fuel lines to the filter bowl. All of this took me about 2 weeks so the truck sat with the batteries out for that long.
After buttoning it all up, it fired right up, a little slower than normal but figured that was air in the fuel lines, HPOP, etc. The only issue I had was the battery light stayed on. Thinking I had an alternator issue, I checked it and it was getting about 14.25v so figured that was good. I used it regularly for about 3 weeks, the light stayed on, and noticed some surging during warm up and some low rpm hesitation.
Then it stop dead on me driving down the road. Turns out it was all my doing, I had torqued the bolts on the water pump pulley but didn't use Locktite. The bolts backed out, shredded the belt, and ended up yanking the CPS wire harness out of the sensor. So that made total sense.
Fast forward another week, got new wiring pigtail and CPS (never replaced it before now) from a couple of the good FTE vendors. I am not sure about the wiring on the pigtail, my truck has a green, blue and brown/gray wires, the wiring diagram I found online showed green, blue and gray. I wired it connecting the brown/gray where the gray line goes (center contact) and closed everything up.
Another thing to mention is that I have an Edge Juice with Attitude that has been on the truck since '06. I lost that connector in the process and they were absolutely no support in trying to get me running again. Wouldn't or couldn't tell me which wire they connect to so I used the green wire which is the CPS signal wire to the ECM. Once I am running again, going to get rid of the Edge.
So that is where I am now. No start, I've been reading some of the "what to do" posts, the most likely is that I don't see the tach bounce when trying to start. So I want to check the wiring to make sure I have good connections to the CPS.
So I don't have any diagnostic software to read codes, etc. I really need to fix this myself and only have one set of hands most of the time. Not really sure what the problem was before it stopped running and now I can't diagnose the surging and hesitating.
View 14 Replies
I bought a 2002 santa fe last week. it was a non runner. the previous owner said he took it to the garage for a crank oil seal leak. when he went to collect the car they had removed the head saying oil was leaking from the gasket. he towed it away and i bought it. i have refitted the head. the engine runs smooth at idle. when i first start up in the morning there is a loud rattle for a second or so. it sounds like a diesel starting up. when i am driving it hesitates and seems to lose power. also at a certain position on the accelerator pedal this rattle is there. it goes away when i accelerate more.
View 12 Replies
I have owned this car for six months. The car now has 39K. The problem is getting worse.
Re: Lexus 2011 LS460 AWD
Subject: Hesitation / momentary loss of power when accelerating after turn.
When accelerating after a sharp turn with light to moderate acceleration, the car will have a momentary loss of power for about 1, 2, or even 3 seconds. This does not happen often, but perhaps once every two weeks and I cannot replicate the problem despite attempting to do so.
In all cases, I am talking about DRY pavement. It always happens after a sharp turn usually to the right. (Probably because most sharp turns are to the right actually it only happened once on a left turn that I will describe below.) Acceleration is light to moderate NOT hard acceleration.
In one case it caused a serious situation. I had just purchased gas and was entering a busy freeway. When accelerating, the engine had a total loss of power for a couple seconds as a large semi truck bore down on me with its air horns blaring.
I have a strong clue that may debug this problem. Once, when turning left, the car suffered a total loss of power. There was no traffic and I kept my foot lightly on the throttle. The car remained unresponsive. The engine did not stop, but it did not respond and remained this way for at least 5 seconds until I took my foot off the accelerator and then back on to the accelerator. During this period of suspended throttle, I noticed that on the right side of the dash an orange alert symbol was flashing I think it was a swerving car? I assume this indicated that the car was losing traction and the computer decided to cut power until traction was regained. But the pavement was dry, and the acceleration was normal. In no case did I ever sense that one of the wheels was slipping.
View 14 Replies
When i got my 2000 jetta vr6 it has a CEL for misfires. Searched this board and google already. Im thinking injectors (havent checked yet) I noticed something weird the other day. At a light i get the CEL flashing. Then after a bit it will come on and stay on. I plugged in my generic reader and deleted the codes. When the CEL is on I get loss of power and hesitation. When its deleted the car runs better. I get my power back. I looked in the coolant tank and see no bubbles. Could this be the ECM? Im still going to get injectors but want to buy the gasket and anything else I am going to need to put it back together. I already cleaned the MAF, replaced some vac lines, coil pack, wires and checked plugs (gapped at .28) ...
View 4 Replies
When I take off from a start it will intermittently stumble or hesitate, seems to be around 1500 rpm. have also noted it at higher speed while cruising. its more like a momentary power cut than a miss fire.
So far I have done the following
new fuel filters
clean MAF
new PCV valve
new spark plugs
check all hoses and plugs etc
injector clean
checked techstream for codes. there is one for a heated O2 sensor but dont think thats it.
2002. SC430
View 3 Replies
I have a 97' hyundai tiburon, I have multiple misfires that are p301 302 304 and rich airflow. I have changed the coil pack, spark plugs and wires, and the MAF sensor. Basically my car doesn't accelerate fast or go over 40(max), it putters when i try to accelerate.
View 1 Replies
Ive got a 2001 f-150, 5.4L, 121k miles. I've replaced the fuel filter, removed and cleaned all injectors, cleaned MAF, changed 2 faulty coil packs, and installed all new plugs.
No codes thrown, truck runs smooth. Problem is intermittent. It will act as though it's got no power, usually won't happen till it's warm. I can drive it for 2 hours, runs strong. Sometimes when I pull onto a highway and get on the throttle a bit, it starts to hesitate, rpm's go to about 3k and it hesitates, but does not miss. acts like trans is slipping but I'm positive it's not.
So when it starts to do this, it's constant. I can continue to drive and it's runs terrible, does ok if you barely use any throttle. But.... I can be driving 40-50mph while it's having this problem, toss it in neutral, turn it off and restart, and all the power is back, great acceleration, as if nothing ever happened.
View 3 Replies
Ok I've been plagued with this very random misfire/power loss/hesitation problem going on a couple of months. You could drive the truck anywhere from 50-300 miles without having an encounter of this problem. It seems to do it now mostly on contiguous long trips over like 30 miles. It one time threw up a P1131 code which quickly went away on it's own. This is a list of stuff that has been recently changed: plugs, wires, coil packs, air filter, pcv valve, fuel injectors, tps, idle air valve, MAF cleaned, fuel filter, and egr valve.
I sprayed with brake cleaner for vacuum leaks around the intake tonight after driving a continuous 50 mile round trip it messed a few times on the way back. When I sprayed the EGR valve mounting area it idled rough when it was hit with brake clean and idled up. So there's a leak there. Or is it stuck? It will be driving normal and usually when you come to a stop the engine will start missing really bad and then when you take off there's no power at all. You keep your foot on the gas and eventually it will feel like all the power is just turned on.
If it does it while you're driving highway speeds it will feel like you've lost a cylinder but it's not as dramatic as when you come to a stop and it starts missing. I can't be 100% but I don't think the EGR wasn't leaking before I replaced it and it was still doing the same thing. I'm wondering why the Check Engine Light won't pick up an obvious misfire when you can you actually feel it. And why if it was the vacuum leak would it only start doing it after many miles of driving?
View 11 Replies
Here is this wonderful 5.4 's issue now, sometimes it will idle rough, sometimes it wont. sometimes it feels like it wants to stall, other times not. if im driving about 30mph up a hill around 1700 rpm, the engine feels like a bucking horse, it will kinda want to produce the power, but cant seem to find it till the trans drops to a lower gear. With this engine power loss is unacceptable because it came out of the factory with no power, i cant afford to loose more.
there is no check engine light. its been doing this on and off for a week. i dont drive it much, may 15 miles a day. i thought maybe it was bad gas , i had it sitting for a month, but since then ran almost 2 tanks of gas through it. Seems to act the worst when driving it, then letting it idle for 5 mins, then drive it again, that's when its very noticeable. no smoke from exhaust, no mixing of oil and anti freeze, plugs are a year old, filter is new.
View 10 Replies
Had this truck a few years now, and it has always had a slight miss/hesitation and maybe a few codes. The timing chain skipped a tooth and the truck was down for about a year. I have 4 other trucks, so it wasn't a big deal. I finally had time to put a new oil pump, chains, guides, tensioners, phasers etc. The truck actually runs very well and quiet. But, now misses far more than I remember it doing.
When driving in town constant at 25-30 mph occasionally it will loose power for a brief moment(<1 second) and then be fine, the security light on the dash turns on for a few seconds. It drives at 55-65 just fine, unless I am going up a hill or something else increasing the load.
2004 5.4 3v 2wd
CEL-
P0453 (fuel tank pressure issue)
P0351 (ignition coil a primary/secondary circuit malfunction)
P0356 (ignition coil f primary/secondary circuit malfunction)
The coil packs are new, and I have injectors on order. Also found this thing on the back of the motor, it connects to the fuel rail on the drivers side. Where it should go. I looked on my other trucks. But my other 04-4wd has a box by the battery it connects to, but mine doesn't have any of that stuff. And my 08 doesn't have anything like this at all.
And a pix of the truck in question.
View 2 Replies
I have a 94 Chevy Suburban C1500 with a 5.7L, 350 Engine. It has 235,000 miles on it. I purchased it about 4 years ago with 191,000 miles in very good condition and obviously well maintained. I have continued to maintain it well.
For the past few months it has begun to start a little slower that before and when accelerating cold or warm there is a spot where it looses power. It doesn't sputter or die it just looses power. I can press the accelerator farther and it will come back to life and do fine. After a 20 -30 minute drive if I park for a while, 20 - 30 minutes, when I start it up it dies. The only way to keep it running is to give it the gas and smooth it out at about 1500 rpm for 10 - 15 seconds. Then I can drive it with no problem most of the time though it still has the dead spot on acceleration.
There is a good spray pattern from the throttle body injectors. Plugs and wires are relatively new and plugs look good (AC Delco Rapidfire Platinum). When I turn on the ignition without going to start, the fuel pump builds pressure for 4 - 6 seconds. I haven't checked the fuel pressure yet and am considering investing in the rig to do so. I recently replaced the fuel filter but that didn't work.
The check engine light has not come on but many of the lights in the cluster are burned out and I haven't felt like going to the trouble to fix that so it is possible that the check engine bulb is bad.
View 12 Replies
2001 V10 160000 miles.
1st happened Wednesday on way back. Temps all fine but had been in stop and go traffic earlier. Truck was on cruise and felt like fuel cut. I disengaged cruise. Throttle would keep it running and within 5-10 seconds it caught and ran fine.
Connected and reconnected all injectors, coil connections, tb and MAF connections. Nothing noted loose. No codes on OBD reader.
Drove around town last couple days no issues. Today towing three dirt-bikes about 45 miles. towards the end of the 45 miles. she stumbled as we crossed an intersection. Then caught and ran fine. Did it twice on way back home towards the end of the trip.
Had OBD reader in gauge mode with ignition advance, tp sensor, voltage and gallons per hour showing. None seemed to change when it stumbled.
Fuel pump is about 2 years old. Coils maybe 4 or 5 years old. Aftermarket. No codes on OBDII reader.
View 4 Replies
I bought a 93 k1500 that was blown up. Replace engine to find out heads are bad and knocks. Got another engine out of a 96 pickup vortec 350 with 50k on it. Before I put it in I found spun bearing on number one. Its not terribly loose or scorn but it is bad and i'm going to fix it.
If I buy the intake to adapt my tbi on top and a new 383 stroker crank and lower end bearing will this cause issues because everything else is stock in that engine?
View 2 Replies
