Buick - Lesabre :: 1994 - Custom Diagnostic Cannot Connect To Or Read ECU / Intermittent Stalling / Rough Running
Dec 5, 2012
I have a 94 buick lesabre custom that is stalling intermittently and runs rough intermittently. We have had it for diagnostics and it could not read the codes. We changed the computer and it still can't read the codes. The diagnostic tool says it cannot connect when it is plugged in or it displays white flecks like snow flakes on the tool screen. It is an OBDII. The pin structure of the data connector port is two pins top row and bottom row two pins some blanks and one pin. We don't know how to fix it with no diagnostic codes and we don't know what to do to get the codes because we have changed the computer.
View 8 Replies
Advertisement
[URL] I even pulled the same P0170 code. And what I need to do before I spend a boatload of money and wind up sleeping in my car instead of driving it to work or lack therof is to start a troubleshooting list starting from where Sabot's update left off, i dont even know where the vacuum line is that he mentions and if i sprayed carb cleaner on it would i get a jump in engine RPM or a stall as a test?
What I have done: Cleaned MAF sensor, changed fuel filter.
What I have not done: Checked all vacuum lines, Tested fuel pressure, Tested for compression issues due to blown head gasket.
there is also a puffing noise coming from the exhaust side of the engine, im gonna grab a bottle of baby powder this afternoon and test for air leaks, i dont believe it is a misfire...
View 3 Replies
1994 Buick LeSabre Custom 3.8 Litre V6 with 103277 miles.
It runs smooth when idling in Park, rough when I put it in gear when I am stopped (either drive or reverse) has hesitation when accelerating, it smooths out again when driving then it starts to drive rough at about 55 MPH.
Mechanic told me it was the plug wires. I replaced those and the plugs. This fixed the hesitation when accelerating issue, but the other issues remain (now even seem a little worse) I thought the plugs and/or wires were bad, so I rechecked the gauge on the plugs and traced to make sure I had the wires hooked up right. Everything seems in order.
I have added fuel injector cleaner, and changed the oil, oil filter, spark plugs, spark plug wires, air filter, flushed the radiator, and changed the thermostat. (For a tune up since it has admittedly been a while)....
View 1 Replies
1996 buick lesabre custom 3800. The car stalls from time to time, and the fuel pump, power windows, power seats, and power mirrors all stop working. Most people who have had this problem cleaned the ground bus on the drivers side under the carpet. I have done this, and the car has not stalled yet, but I haven't driven it far because I have noticed the fuel pump relay and power windows relay are getting extremely hot to the touch after 5 minutes or so of driving. Why these relays are getting so hot? I cannot afford to keep getting the car towed home.
View 1 Replies
I own an 87 Buick Lesabre Limited Coupe [URL] ..... I have driven it for the past 6 years with no major problems, but just now it has begun to have a stalling problem. The engine just shuts off at random times. Doesn't matter if you're at a red light or driving in traffic. She will stall, then after 5 minutes will start up again, and stall again. So, I took to it to my mechanic & he changed the ignition module & mass air sensor. I picked it up, and the 'Service Engine Soon' light went on, and then she stalled a few minutes later.
So, I drove her back to the shop (stalling several times on the way), and my mechanic changed the crank position sensor, and she still died. He read the trouble code 42, so he changed the ignition module again. I picked her up yesterday, and she made it home without stalling, but the 'Service Engine Soon' light still goes on after 5 minutes of idling, which leads me to believe that the problem lies somewhere else. Could it be an electrical problem (wiring, fuses, computer) that is causing the 'service engine soon' light to go on & the car to shut off? What else could it be?
View 2 Replies
My Buick has started acting weird and I've had a hard time figuring out what's going on. As I understand it 94' was the transition year for the OBD1 and OBD2 sensors, therefore auto zone and o'reilly haven't been able to pull codes on my car. It runs off of OBD1 codes but has 16 point OBD2 sensor pins.
Here's the problem: When the car is started it revs up to 2000rpm at idle, when shifted into neutral the rpm jumps up to 3500. In drive and reverse it goes back down to 2000rpm. While driving the car is hard to stop and surges when I take my foot off the break, it also gains speed on flat ground without touching the gas pedal. After driving the car when I put it back in park it revs back up to 3500rpm and is quite noisy.
I've replaced the mass airflow sensor, cleaned out the entire throttle body (there was a little carbon build up but not too bad), replaced all the vacuum hoses(that put a stop to it for about a week), and I'm still having the same problems. I recently replaced the a/c pump because the bearings went bad but I don't think that would cause any problems like this.
I have a very, very slight gasket leak on my valve covers but it's been like that for the last few months and the car was acting fine. The car has done this before but it usually stops after you drive it somewhere. The hotter it's gotten out the more often it started happening and now it's not stopping like it did before.
View 3 Replies
I have a 1994 Buick LeSabre Limited with a 3800 engine.When the engines cold,it starts fine and drives fine.When it reaches operating temp,if you shut it off. It will crank but not start back up until its cold again. I've replaced the crank and cam sensors but no change.
View 2 Replies
I have a problem in the form of a 2000 Buick LeSabre Custom with the GM 3800 series II engine. After 245k miles, it has begun to show it's age in some very unaffectionate ways. It has been stalling, sputtering, hesitating, and unwilling to start at seemingly random intervals. And, such is my luck, there has been no 'check engine' light on at any point during this saga. Here's the chronology of events spanning 6 months:
The first symptom I experienced was occasional sputtering, mainly while going uphill. This began to occur shortly after the spark plugs were replaced during regular maintenance. So I replaced the spark plugs again, and also the wires, fuel filter, and fuel pressure regulator. Plus I gave the MAF a good cleaning.
But the problem persisted, and grew to include intermittent stalling when I would come to a stop. Undaunted, I replaced the ignition coils, and swapped in a used ICM.
The car, obviously displeased with my choice words toward it, began to not start every now and then. It would just crank to no avail. So I would try again after an hour or two and it would immediately start as if nothing was wrong. Fearing that I or my wife could be left stranded I replaced the fuel pump. It continues to stall every once in a while and it still sometimes sputters at low rpms. A lot of times it just wont idle at a constant speed.
So then I replaced the crank sensor and I cleaned the camshaft sensor too. Guess what? It's still intermittently sputtering/hesitating when I accelerate from a stop. And I have noticed that it will also sputter while idling in park as well. It's like it's misfiring, but with no engine codes. I'm not happy.
View 4 Replies
Since our weather has turned cold with lows just above 0ºF and highs around 10ºF, and we've had 9" of snow this week, I have been driving a seldom used 1994 LeSabre rather than my "nice" car, an '08 Grand Marquis. There's no point in exposing the newer car to salt and slick streets. At least the interstates are completely cleared off. The LeSabre runs great despite its 177K miles. The only issue I have with the Buick is that it has died repeatedly after a 20 mile run up or down the interstate. I lift my foot or tap the brake pedal to turn off the cruise control, and the engine dies. The first time it did it, I pulled over, stopped, put it in park and restarted it. Now that I know what it's doing, I keep rolling, put it in neutral, and restart it before getting to the bottom of the ramp. I does it ALMOST every time after a long 65 to 70 MPH run. It was not doing it the last time I drove it at more bearable temperatures, in the 40s or 50s so it may not be a problem next week. It does not seem to do it going from stop light to stop light, even at low temperatures. It has the 3.8 Liter V-6. Why it might be doing this?
View 10 Replies
My 1995 LeSabre (3800 v6, 62K miles) has a stalling problem, no engine power, but still has electric. It happens randomly and intermittently. Most times it will restart but has been increasingly difficult to restart. The only indicator prior to stalling is the speedometer "surges" and then the loss of power. Dash lights come on (oil, voltage, CEL). Sometimes the CEL will flash in time with a fast clicking that I believe comes from the fuel pump relay under the right side of the dash. Until this clicking stops the engine will not restart. I have replaced ignition control module, and then the crank and cam sensors. Replaced PCM with rebuilt and it was worse (defective?) and put the old one back in. Mechanic can't find any codes to determine what is causing it to stall, except possibly PCM is bad.
View 11 Replies
1997 buick lesabre, 4 door, v6. It was having problem stalling out. This weekend a friend and I lifted the car and replaced the fuel filter and fuel pump. Drove great Saturday and Sunday. Today I get in the car, starts up without a hitch. I start heading down my street and realize I am having to push my brake pedal in ALL THE WAY to get it to stop and even then it's slow to stop. So I back up, pull the hood and check the brake fluid. Sure enough, it's low, so I run to Advance, grab some fluid and fill it up the max line and think i'm ok. Start the car up, pump the brakes a few time and notice nothing new. I get out and realize I have a very steady leak in front of the right rear wheel of fluid. It's a steady drip in two places. Is there something I could have done to have caused this. The only line we messed with on Saturday was the emergency brake line and it's clearly working (I tested it).
View 1 Replies
My 1995 Buick Lesabre will intermittently drain the battery after sitting for about 12 hours. It is unpredictable. The battery was newly installed in December, 2010 and the alternator was tested at that time and about three weeks ago and proved to be recharging properly. This battery kill happens even when there is no visible sign of current usage, such as a dome light being left on. What I should look for in order to to find the source of the current drain?
View 2 Replies
I have a 1998 Buick lesaber it ran hot the other day [temp light came on] do I pulled in to gastation and the overflow tank was empty I filled it to the hot line and ran it for a few minutes light went off drove 8 blocks to my house let it cool down and opens the radiator cap no coolant. I checked the overflow tank empty too. So I got some coolant from my garage and poured it into the radiator as I was pouring it started to leak out somewhere on the upper passenger side of the engine under the plastic noise cover and behind the pulleys. This happened while the car was not running. It's my family's only car so I can't tear it apart until the weekend but where to start or what parts to have on hand.
View 9 Replies
Engine light won't go off - printout says it's running lean - replaced mass airflow sensor, upper & lower O2 sensors, spark plugs, wires and coils. What else I need to do to get the light to go out so it'll pass inspection?
View 4 Replies
I have diagnostic trouble codes P0K92 and P0K7K set on my 2008 Gen. II Prius. I have searched the forums and cannot locate these two codes.
I started and drove my car for several miles today, then it started to run rough. I pulled over, then called a tow truck to tow my car back home. I have a high-level scanner/code reader that read P0K92 and P0K7K codes.
View 19 Replies
The problem began with intermittent stalling and now the Jeep will not start at all (no spark). I have had the cap, rotor, primary ignition coil, crank sensor, cam position sensor and PCM replaced without any luck. The repair bills have been brutal. The garage has given up.
View 8 Replies
I am having a very tricky problem with my Buick.
For approximately the last 4 months, it has been (at least according to the heat gauge on the dash) running pretty hot. Not overheating, but getting close. And it doesn't take long for it to get there. This all seems to have begun right around the time that my father and I flushed the coolant system.
Since then, I have replaced some parts, and learned a few things in the process.
I learned that there are bleeder screws which can be opened to let air bubbles out. And I have heard that the 3.1L is especially susceptible to them.
New parts which I have installed:
- thermostat
- coolant temperature sensor
- radiator cap
- upper radiator hose
- lower radiator hose
I have checked the water pump and it seems to be perfectly fine. No leaks. No signs of bad bearings. And it circulates coolant just fine. I have not been witness to either cooling fan, primary or auxiliary, switching on in a while.
The exact symptoms are these:
The heat gauge does not take long to get to mid-way point, but will sit at that point for a bit if the vehicle remains stationary. Once the vehicle is in significant motion, the heat gauge will climb fairly quickly, especially with moderately high RPMs. It WON'T touch the red though, but will get very very close to it. The car runs fine. It does seem to be a bit underpowered, but I am comparing it to my fiance's 1996 Olds Cutlass Ciera, which I believe has a different transmission. My Buick does not seem to have lost power since this problem arose. The cooling fans no longer kick on. The oil appears fine. The coolant as well. With the radiator cap off, coolant does not bubble out or shoot out.
I made sure after changing upper and lower hoses to fill the radiator, let the car run long enough for the thermostat to open, and then slowly poured more coolant into the radiator until it was full again. And the reservoir is at proper level and the the reservoir hose s not clogged.
I am not SURE, but I don't believe the radiator is clogged. I believe that covers it, at least as well as I can.
BTW, I do not know where the fan relays are, otherwise I would test the fans to see if they still work.
What the heck is up with my Buick? Also, it has 97,xxx miles on it, and the transmission fluid is at proper level and looks normal.
View 4 Replies
Car:2000 Buick Regal54,000 miles3.8 V6, Vin K
Problem:The engine quits running. Idle, part throttle, moving, stopped, open or closed loop doesn't matter. Sometimes it will re-fire immediately, other times it may take a dozen or more attempts.
There is no MIL, and my TECH 2 is finding no issues.
View 8 Replies
I have a 2003 Subaru Forester, bought it this past January. Got 163,000 miles on it, and we've driven it mostly around town. Over the last month, it has developed an intermittent problem with stalling and rough "putt-putt" running, and will only keep running if the gas pedal gets pumped. This seems to happen about every other time we turn it on, but without a pattern. It can be running fine, and then switch mode, as it were, to running rough and tending to stall. I've gotten ignition codes (check engine light came on and I had my guy check it out on the computer) twice. My mechanic (a long-term Subaru mechanic) has checked out the injectors, and replaced the head gasket, but the problem has not changed. I'm thinking that this may be an electronics issue or possibly something in the gas tank/line.
View 1 Replies
About 2 weeks ago my 1997 Buick Park Ave (115,000 miles) began running bad during a heavy rain storm. It was running fine. Then all of a sudden at a stop light the motor hesitated and wanted to stall. I nursed the gas peddle and limped home and turned the car off. The car hesitated and sputtered all the way home as if I was running out of gas.The next day the car would not start. It turned over but would not start. I tried starting the car for three days. My mechanic friend later diagnosed the car and stated the computer was not functioning correctly. He replaced the computer. The new computer seemed to correct the problem.
The car ran great for the next 2 weeks. Yesterday, it was raining hard while I drove the car about 150 miles without any problem. Then suddenly again the motor started running badly. Again, the motor wanted to stall and hesitate as if I was running out of gas. I limped home again. This morning I tried to start the car without any luck. In addition to installing a new computer, In the last 2 months I have changed all the fuel injectors and installed new spark plugs.I have also changed the fuel pump and repaired the fuel tank. My mechanic say the cam sensor and crank sensor are operating correctly. There is spark coming from the coil packs and to the spark plugs. I do not want to randomly change parts.
View 3 Replies
94 Ford Ranger 2.3L
I started to have a slightly rough idle a while back, but not severe. I figured she was just aging a bit.
Changed plugs. Check engine light came on. Changed plug wires. Then I had a couple of episodes where it started to lose power and idle really rough (stalling). Both times it stopped after a few minutes. Had code read- they said it was coils. Replaced ignition coils. Check engine light still on, but it went a few weeks without power loss.
Tonight the loss of power returned and didn't leave, and I had a glowing red catalytic converter after I limped home 20 miles (hope I didn't do any serious damage, I was stranded.)
Found this post : [URL] .... But there's no resolution.
So, I'm probably dealing with a misfire, and I'm sure I torched my cat after tonight. So any other easy diagnose/fixes for a misfire? I'm a shade tree mechanic- so I know just enough to get myself in trouble. If I can't get a resolution soon it will be off to the mechanic (which, maybe I should have done 1st...)
View 2 Replies
