Buick - Lasebre :: New Electrical Connector In Tank / Pump Won't Start - Reverse Wiring?
Nov 18, 2015
I changed a fuel pump that a service shop said was bad. It would start and run for a few minutes and then stop. If it started at all. I dropped the tank and put a new pump in. The car did not start at all, not once. Not even fire. I had to install a new electrical connector inside the tank on the pump. The connector was different than the one in there. I connected black wire to black and grey to grey, thinking that made sense. Took off inline fuel filter next to tank. Had someone turn on key to see if fuel would come out. Nothing. But I did hear fuel running loudly through the return line. Which confused me at the time.
Thinking of it over night, could it be not likely, very likely those lines are in reverse, causing the pump to pump backwards. Which is why I heard fuel going through the return line? If this is the case I am going to try tomorrow to reverse the lines going into the tank. Instead of the fun of removing tank again. Why would pumps have black and grey wires that hook up differently?
View 19 Replies
Advertisement
I need to wire up a trailer lighting connector for my 2000 Buick Century but I can't find the wiring run for it. Where would I find them to be able to tap into them?
View 3 Replies
My 92 F250 5.8 won't start but fuel pump runs all the time the key is on. Some times it runs. But has no power and check engine light is on.. But I cant get it to flash codes, only steady light on.. It did this before then ran good. Now back to no start.. I checked grounds and relays ..
View 2 Replies
My 2001 Buick Lasebre is not starting properly. I have to pump the gas several times before it will start; then when it is started at low speeds or idle it wants to stall. As long as I can some how keep pushing the gas peddle it wont stall. On the other hand when I am driving at higher speeds, anything above 40 or so it runs perfect. The check engine light was on and shows EGR valve stuck open. I have replaced the Mass airflow sensor, fuel filter, and the EGR valve. I had the code cleared and a short while later my check engine light came back on with the exact same reading. I bought this car only a week ago and was not expecting to have to fix a car I just bought and ran fine while test driving it. I have read may different forum that say that it could be anything from my fuel pump to vacuum hoses, to some other sensor.
View 19 Replies
I have a main tank and an Aux tank with a gauge selector switch. I believe I may have a bad fuse as the indicator has stopped working. Where it is on the fuse block??
1978 Ford F-250
View 1 Replies
What I am trying to do it put in 2 led spot light for added backing up light. What i want to do is have them turn on when put into reverse but also have a switch i can use to turn them on when not in reverse. Just need to know what relay I need and if it even can be done.
I was also thinking of just taping into the wiring harness and adding a wire that goes to the spot lights and another wire that goes to a switch that I could turn on and supply power to the light when not in reverse (I know it will light the revers light also) but is it ok to do that?
View 5 Replies
SO, my Buick has given the code for bad TPS, and it was replaced a little over a year ago...and now after the same symptoms, replaced again.. However, this time, right after replacing, it gave the code again, and still stalls out /doesn't want to stay running especially when put in gear. My regular mechanic also recently just put on a new catalytic converter and a new fuel pump and fuel filter. I'm at a loss, and desperately need my car back.
A little back history...about 3 years ago a 'friend' was to work on my car to install the thermostat and power washed the engine...which shortly after started having all kinds of electrical issues. Right after that, my mechanic had to install a coil, spark plugs, new ignition panel and the 1st tps.
View 8 Replies
My 1999 Ford Ranger XLT, 6 cylinder, auto trans, with 134K miles has an electric problem. When I turn the key to the 'on' position, all dash lights show normal, headlights work, radio plays, etc. But when I turn the key to the 'start' position, all electric power is lost. The power remains lost until I disconnect and reconnect the battery ground wire. After reconnecting, I again have power until the key is turned to the 'start' position. I was able to jump start the truck, so I assumed I needed a new battery. I bought one a week ago, and was back to normal until today. The truck started, I drove 4 miles to the grocery store, and then I found myself back to square 1 (i.e., the no-start situation).
View 3 Replies
I just bought a hard to start 1990 F250. Per the board, just replaced all 8 glow plugs with Motorcraft. Still wouldn't start (it turns over but will only start if you use either). I attempted to install a new BWD brand (Borg Warner I believe) glow plug connector relay today...I removed the old no problem, but am unsure what wires to plug where....the only connection that I'm sure about is the blue wire that works the WTS feature...it plugs in easily but I don't know if there are other connections that need to be made or not? All the wires run from the posts and into the bottom of the unit.
View 2 Replies
I have a 1994 Ford Ranger king cab 4x4 with a three inch lift kit on it . My problem is the fuse is blowing that goes to the fuel pump . It started out blowing the fuse now and then when it was raining . Well I thought it mite be the fuel pump going bad but after I put the new pump in the truck it lasted about a week and started blowing fuses again . I put another fuse in and it go a few days and blow it . Last week on a 100 mile tripe I got almost there and it burned a fuse on the highway . I tried to put another fuse in and it would blow it as soon as I tried to start the truck . Burned five fuses right then . So I had it towed to mothers house and put another fuse in and it cranked up . I looked at the wiring that was not wrapped in that plastic cover stuff and have not found anything yet ...
View 14 Replies
I have 2 1986 Ford F250 supercab I switched cabs to put the better cab on my truck power windows wipers heater blower motor all light signals work no fuel gauge power or fuel pump power no power to the inertia switch
View 12 Replies
so I recently purchased a 2007 f350 SCSB and my reverse lights don't work. I am trying to trouble shoot the cause... So far I've replaced the bulbs and tested the plugs and im not receiving any power to them... Where to start to look for the problem?
View 3 Replies
I have a fuel pump I want to install I want to hook this thing up on a switch inside the cabin to be used as kind of a security device, but I am hoping I can wire it into the ignition as well.... I want the pump to activate when the ignition is turned on but only if the (hidden from view) switch is in the "on" position. Not sure if all this is possible.
I have heard I ought to utilize a relay to avoid voltage loss at the pump. I have never hooked up a relay to anything before although I have heard of them being used. This system is being installed on a 1967 F250.
View 6 Replies
My vehicle would not turn over and we could tell it was fuel related. The fiel pump relay has burnt through the motherboard of the fusebox. It is my understanding that this cannot be fixedand another fusebox must be installed. I have been to many junkyards in my are looking for it to avoid the dealer prices..all of the expeditions that we have found locally have already had the fusebox pulled. Any other vehicles that this might be interchangable with? My friend has an 01 expedition..would this work?
View 1 Replies
I've searched all over and can't seem to find the answer. When I pull the tail light out of my 12 F150 there is a blue/wht wire and a black wire going to the back up light. I assume the blue wire is the positive and black is the ground. Is that correct?
View 8 Replies
My hazard, reverse don't work. The over all instruments panel light doesn't light up (the small bulbs work). Gauges with needles work. I'm putting every thing back into the truck. I left the steering wheel resting on the floor while cleaning and also left the wiring in. Everything else came out because I had to clean out the smell of mice. After I installed the instrument panel I started the truck, there was no hazard lights. I checked all the fuses under the dash. I checked all the fuses under the hood.
I did have a bent brake plug blade to bend straight. I need to replace a bad key cylinder, you can turn it without a key. I believe there were three plugs I unplug to lower the steering wheel. Park brake, brake pedal and a plug under the steering wheel. Wipers, interior ceiling light work. I believe there's a switch on the column (?) that includes the wiper arm. Should it also operate the hazard lights ? The steering column is installed, I can drive it around. Outside cargo lights won't go off, even with the light switch pushed in. Everything worked before.
View 7 Replies
I would like to hook up some auxiliary reverse lights, I want to use a relay. And activate the relay when I put my truck in reverse. I would like the relay to be in my custom relay/fuse box under my hood near my battery. I'm looking for a wire I can tap into, to use to active the relay as close to the battery as possible. Or at least a wire on the outside of the cab near the engine compartment. Maybe there's one coming from the tranny? I have a 2011 f250 super duty. XL, I think, its a very base model truck no power windows or locks, only fm/am radio, no NAV system, no remote unlock, no nothing, 2 wheel drive.
View 9 Replies
2002 Ford F250 V10 Auto... When I put the transmission into reverse, the starter kicks in...
View 8 Replies
OK, this one has me stumped...I have a 93 F150, 302 with the E4OD. I know the transmission needs to be rebuilt (probably a bad pump). When I put it in reverse, the engine will start to bog down and will die unless I put it back into park or neutral.
If the engine does die, the fuel pump does not prime with the key "on" and the engine obviously will not start. If I let the truck sit for about an hour, the fuel pump primes like it should and the engine starts right up. The fuel pump shut-off does not trip and all fuses are good.
View 5 Replies
I am wanting to wire my 03 f250 cargo (3rd brake light area) lights to come on when i put my truck in reverse.
View 1 Replies
My car would not start yesterday, and I realized the fuel pump was not running. So I bought a new fuel pump today and put it on, the car still won't start, the fuel pump still does not run and I have been told to check the relay. I cannot find the relay for this car.
View 7 Replies
