So the gas gauge stopped working correctly over the winter and now in addition to that the DIC is telling me "Check the gas cap". I put a new GM cap on, the filler neck was rusty so I sanded it and applied some oil to the lip of the neck and the cap.
DTC code is 440 and I keep getting informed to check the gas cap. The car has 120k miles on it.
I have a 1990 volvo 240 dl and the gas gauge no longer works. Just wondering if there's anything I can do to fix it.
View 1 RepliesThis morning I started my car and all was well, all gauges working. Drove 2 miles and stopped to get gas. Put some gas in my car and started it back up. My gas gauge never went up. Stayed slammed down to the E. All my other gauges were working normally except the gas. My gas light was not on saying I was on E, and I don't have a CEL.
View 5 RepliesMy fuel gauge just quit working along with the "miles till refuel" in the message center on my R. Before I suck it up with a trip to the dealer, Is there a sensor on the fuel tank that goes bad?
View 3 RepliesDriving home from work today, normal day in the high 60s, my temp gauge randomly stopped working. It was right at the 190 mark where it should be then a few miles from my house it just dropped to 0. When I got to my house and turned it off the fans stayed on for quite a few minutes.
I went inside and looked around on a few different forums. Most people said it was the thermostat or some sensor that could have crapped out.
Probably 30 minutes later I went out to restart it hoping the problem magically disappeared and it actually did. Start up and went straight up to 190 as it should. Turned it off to no fans as usual.
What this could be? Could it just be a sensor on the way out? Still under warranty so might try calling the dealer tomorrow when they open to ask for their input.
Just as reference my car is a 2011 with about 48k and is revo stage 1 for about 3k.
this thing stopped working on me today, can i fix it? or how can i get another one?
04 Ex
I have a 1997 Cirrus. The ABS light came on about 2 weeks ago -- this is after i drive about 30 yards. The brakes seem to be operation ok and when the light does come on there is no bell or chime sounds to indicate something is wrong. ALSO, the RPM gauge just started to not work. Occasionally it may operate correctly but most of the time it just sits on zero. What the fault or faults are?
View 1 RepliesI have a 1991 F-250 Supercab with the 7.3 L Diesel and twin fuel tanks.Recently the gauge sender for the forward tank stopped working. Ford tells me that the sending unit is obsolete. Perhaps they want me to buy a new truck. I recently found a NOS sender on E-bay but it is supposedly for the plastic fuel tank and mine is the steel tank. What steps would I need to take to make this sender work in my truck? Do I need to eliminate a ground wire, add aground wire, or make up insulators to prevent the sender shorting out on the steel tank?
View 2 RepliesI have stock 02 F350 7.3 with 74,000 miles ... Today i looked down and noticed my RPM gauge sitting there at 0 ... It was working just fine yesterday. I figured before i go digging around looking for the issue id see what is causing it not to read ..
View 3 RepliesI have a 2003 F250, 4x4, 5.4L and today my fuel gauge stopped working. I don't know if it had anything to do with a stall, I was on an exit ramp and the truck cut off, I quickly restarted and no issues after that. Other than the fuel gauge not working at this point.
I looked at the fuse panel diagram and there is no fuse for just the fuel gauge. The only thing I see is #35, instrument cluster. The rest of my instruments are working, so what else would cause the fuel gauge to stop working? It had a little over a half of a tank before the stall, after the stall it went down to less than half. I filled up shortly later and it's just stuck at less than half.
I have an issue with my 960 wagon. When I first got the car this past July, the AC light was flashing. I ignored it because I didn't really need the AC. I knew the heat worked fine, which I need up here in the northeast. However, a week ago or so the heat suddenly stopped working. It worked fine in the morning. I parked the car in a lot, came back about five hours later, and no heat.
I found the sheet with the AC diagnostic codes on it, and followed the procedure to get the codes.
[URL]........................
I'm getting the code 132 every time I do the diagnostic, and sometimes I also get 161. Of the three times on three different days I've done the diagnostic, the 161 only came up once.
In-Vehicle Temperature Sensor
Open Circuit Or Short Circuit To 12 Volts .......... 132
Solar Sensor ......................................... 161
I'm not sure where the in-vehicle temperature sensor is. Is it in the dome light? It says the "courtesy light fixture" in the docs, so I'm not sure this is the same thing. The dome light is not currently connected in my car. I have two of them in the garage but neither ever produced light when plugged in, and the heat worked fine all during that time, so I didn't worry about it. It was only until a week ago or so that the heat stopped working.
The temp panel controls work fine. Blower blows as needed, vents switch no problem. Recirculate actuates. No heat.
My AC stopped working a few weeks back. The garage looked at it and noticed it had no refrigerant, the fault code stated this also. It was traced to the condenser which was replaced and the system regassed. The AC will still not work. The current fault code is 00716 Air Recirculation Flap Positioning Motor (v113) 005 - No or Incorrect Basic Setting/Adaptation. That is the only fault code showing and cannot be reset.
There is no cold air at all. Could this fault be preventing the AC from working? What is odd is that the compressor seems to be running when you switch on AC as it shows up in the diagnostics as running with about 2nm of torque.
I'm having trouble with my 2000 Grand Caravan 3.3L. The gauge cluster was working intermittently & recently quit. I have the P1698 trouble code & looked up info online. I of course found out about the solder joint problem & figured that would be the culprit. I took the dash apart & found the solder joints were fine, but when coming apart, the wire plug on the back side came out on it's own. The retaining clip was broke & I thought maybe that was my problem. There's enough room to install a zip tie to hold the plug in & I put it back together. It still doesn't work though.
Here's the symptoms- I turn the key to ignition & nothing in the instrument cluster comes on. When I start the engine, everything lights & works as normal except for the trans indicator- the letters light, but no position shown (regardless of any gear selection). This continues for about 5-10 seconds & the trans position indicator lights up around EVERY letter. A few seconds later the entire dash goes down. I then shut off the engine by only turning the key back 1 notch. At this key position the odometer & trans indicator come on & the trans indicator will properly display every selected position correctly. It is consistently working this way every time now. The heat is also stuck on hot & the rear window wiper/ washer is not working.
I've also pulled the body module to check for connection problems & don't find anything with that. I've pulled the fuse under the hood too. So far no luck.
My 2001 Malibu v-6 temp gauge is not working. I have replaced the temp sending unit and it works for a few weeks unit it goes out. What keeps killing the temp sendor?
View 6 RepliesI have a 2001 Ford Focus. A year or two ago, I noticed that the fan (and therefore front defroster) really only worked when it was on the maximum setting. I was and still am a poor student, so I didn't bother to get it fixed. A few days ago, I noticed that the fan was no longer working at all, even if it was on the maximum setting. I checked the fuse under the hood and it was in fact blown.
I bought a new fuse and replaced the old one, thinking that I would lick the problem. Unfortunately, no such luck. Based on my reading, it sounds like the blower motor needs to be replaced, but I don't want to sink tons of money in a project if that ain't it. Does my suspicion sound reasonable or is there something else I should check?
Now, if that sounds right, I figure this is something that I can do by myself fairly easily. Will I need to purchase a new wheel as well, or just a new blower motor?
My 98 Bonnevilles abs system no longer seems to work. It's been like this for quite awhile now, but I have been overhauling the car and would like to fix it. It stops as if it doesn't have abs and yet the light never comes on. I'm going to run some tests on the wiring.
View 2 RepliesI have a problem with the air conditioning. It stops working when the car is in idle or driving below 40kl.
View 1 Replies03 santa fe... During a stereo install the door panels were off and somehow we found a way to screw up the window switch. (the good new's is the stereo sounds awesome) and I can't pass it back onto the installer, he's my brother
all 4 windows stopped working, and of course, they are in the down position which complicates things just a bit
I checked the fuses but they seem ok at least on a visual, although I haven't eliminated that all together the likelihood that its a fuse, or multiple fuses is moving to the bottom of the list.
The window switch, it looks ok on a visual, anything obvious that I can check or look for ? No loose or crimped wires that I can spot.
If the switch itself somehow got fried I can get a replacement, but I'm hesitant to just go out and buy one right now (75ish + ship) and get it in the mail, to get the ball rolling, and god knows what the dealer would want for the part locally. I'll also check local salvage yard to see if at least I can get the part faster if it comes down to that.
Maybe when the new speaker wires were fished through the flex boot we disconnected or loosened the connector under the dash that goes to the switch ?
The rear wiper on one of my two 2004 Santa Fe has stopped working. Checked that the fuses are OK.
Then I swapped the wiper motor and then the control unit to the other Santa Fe & both work in it so are OK.
What else could be causing the problem?
My 2002 Santa FE's cruise control has stopped working, light comes on but no hold or anything, any obvious faults they have that I can try. I checked the fuse, that's OK...
View 7 RepliesI own a 2004 hyundai santa fe and just recently my turn signals have stopped working. My bulbs are fine because they still light up when I lock my car and my hazards work too. The flashing arrows on my dashboard wont show up for my turn signals but they will show up for hazards. I checked the fuse and its completely fine. I am so confused with what is wrong. The only thing I was doing before was messing with my new head unit which involved unplugging a lot of the stereo and fog lights and hazards but that all should have no affect on my turn signals.
View 6 Replies