BMW :: 1999 Responded By Idling Up To About 1200 RPM And Then Dying
Jul 19, 2011
My 1999 BMW 3 series, with 112K, full synthetic oil and a 5 speed transmission does great, except for one minor issue. About once a week, when the motor is warm, it dies. Tonight after driving it about 20 minutes on the highway I came to our hill, put it in 1st gear to come up (like always), and then came to the flat part where I put it in neutral to coast the few feet into our driveway. The car responded by idling up to about 1200 RPM, and then dying. It always starts right up the 1st time (even after sitting for 2 weeks), and it is absolutely otherwise reliable. My initial thoughts were something with the idle control valve?
View 1 Replies
Advertisement
When I'm idling and I rev the engine to exactly 1200 rpm i can feel an extra vibration coming from the engine. If i hold it at this rpm it will continue on. now this is not a violent vibration but more so of a buzz i can feel that travels to my steering wheel as well. what could it be ?
Another question is when i travel up my driveway and i hit the sloped curb at a angle i can hear a specific "clunk" sound coming from around the drivers foot well area what could this be? perhaps my axle going bad? I also heard it when I was reversing out of my parking space while turning.
I am new to this car and trying to make sure I'm doing everything i can to put it into good shape.
View 3 Replies
My 1997 f150 5.4 has started an idle issue. The truck when started will idle around1200 rpm and not settle down After driving a bit it will drop down around 800 and idle rough and sounds like it has a plug fouled. As soon as you give it gas it clears up and sounds fine, then drops down an idles rough.
Checked for vacuum leaks but don't see any. pulled the MAP sensor and cleaned it, but did not change.
View 7 Replies
I have a 2005 5.4 F-150. First off it came to me on a rollback because the owner tried to replace his plugs after he noticed it missing and of course broke one off. So after I extracted the plug from #8 cylinder and installed a new plug I cranked the truck and it was idling very rough and had a terrible miss around 1200rpm. I pulled the codes and got several misfire codes and ignition coil faults on #5,6 and 7 cylinder. Popped in 3 known good coils in these 3 cylinders with no difference.
On Mode 6 on my diagnostic software you could watch the misfire count steadily increase on #7 and every now and then there would be a single misfire on #5 and 6. It also had several codes for O2 sensors biased, stuck rich on that bank. Well since it had a brand new plug and coil, I popped an injector in #7 and havent had a single misfire on it since and it also started idling alot better and all the O2 codes went away. The problem I am having now is #5, 6 and now 8 will randomly misfire, sometimes build up a steady count on one of them, sometimes just skip around between them.
The truck has brand new plugs in all 8 and new coils on this bank also. The truck has 115,000 on it and does have some cam phaser noise on the bank causing the problem, but its not too terribly bad, I have heard alot worse. My problem is something on that bank only as the passenger side bank is fine. I am wanting to say cam phaser now since this is the side with the noise. I have changed them before but have just experienced the noise, never one running like this because of it. Possibly jumped time a little?
View 14 Replies
I have a 93 Corolla LE and in October I was driving in heavy rain and the car died. Since then I have replaced the spark plug wires, plug seals, distributor cap, battery, and rotor. The car would get me from A to B, but I would always have to put it in neutral at a stop to keep it from dying. This past week we've had a lot of rain and it's been really cold so my car has been dying when I slow down or stop. I gave it plently of time to heat up thinking it would work, but it died three times on the way to work.
View 15 Replies
Car was idling and driving real rough and dying at stops. Turns out that the transmission mount was torn so I replaced it and verified that the other two motor mounts were good. Car was still running rough but on a drive with some jerky shifts (automatic) after about 20 miles all is well and I'm running as smooth as a baby's bottom with great turbo action. Cars just don't fix themselves. What could have been wrong? By the way there were no codes from the Tech ll. Using a pc of tubing I can't hear any vacuum leaks nor when spraying brake cleaner on the hose ends does the engine race.
View 3 Replies
My brother's 5.4 has been rough idling and dying at stops and in reverse for a few weeks now. Today it threw a code and he finally had me look at it and it's a P0345 code. I was thinking cam phasers possibly, but I didn't think that would cause a code to throw. Also, all I hear about cam phasers is that it makes the truck sound like a diesel, but his when it's about to die sounds like the engine is about to drop out the bottom of the engine bay. Really rough, REALLY loud knocking, etc... What we should be looking at replacing to get this thing back into shape?
View 3 Replies
I pushed the handsfree button on the wheel today and said "Call". System responded after a bit with "No Network Signal". I tried to dial via the nav screen and it tried connecting for a bit and then just stopped. I was streaming music via bluetooth without a problem.
View 2 Replies
I have a 1999 Ford F550 with a 6.8L V10 and a 4R100 Auto.
I want to run an underhood hydraulic pump, like what a wrecker uses only I want to use it to run a generator under the truck.
How can I get a 6.8 to idle up to 1200 or so? I searched the Body builders guide and it looks as if the idle up is for the 7.3 only.
My truck also is not a 2005 and up like the other posters, who can take advantage of a drive by wire.
Also I doubt my transmission has a PTO cover so I think a generator option using that route is a dead end. What are my options to idle the truck up to 1200?
View 2 Replies
I am still trying to debug my 7.3 running sluggish in the 1200-1800 rpm range. The problem is intermittent. I checked the wiring harness under the valve covers to verify they are plugged in and there are no opens in the circuit. I replaced the crankshaft position sensor and the high pressure oil sensor.
This will run fine one time and a few miles down the road it will chug and smoke out the exhaust until I either get into the accelerator or back off and re press the accelerator. Again, it does it intermittently hot or cold.
I ran both a cylinder contribution test and perdels with a Snap On Verus. The cct passes everytime. The perdels have a couple of cylinders 5-6 and 8 fluctuate between 0 and 1.80% with #8 up to 2.5%.
My question is. Do the cylinders in the test correspond to the actual cylinders in the engine? Reason I am asking is the Verus does not follow the firing order on a gas engine. The cct is in order of 1-8 and I have to correlate the cct order to the firing order. Found this out the hard way when I had a bat cop on a 5.4 and replaced it only to have the same cylinder still show not firing.
I got out the graph leads and tested the cylinder and pulled the injector thinking it was bad. Everything showed good but the cct still showed it not firing. I had to unplug each coil and watch the cct to determine what the true cylinder in the test was. It turned out to mimic the firing order so I am asking out of concern that cylinder 3 in the perdels is really cylinder 3 or a different cylinder.
Btw, the perdels all show 0% if the transmission is in drive. I would have thought that a load on the engine would have showed higher perdel percentages with a load on it.
View 13 Replies
I have 2005 f250 5.4l 3v that was having miss problems between 1200 and 2000 RPMs. Changed VCT solenoids which worked, but then could hear chain hitting cover when powering down throttle on left side. Figured chain tensioner was bad, so tore down and removed timing cover. Found left chain was tighter than what seems normal, and right side had huge amount of slack. While taking off tensioner on left side, something happened to fast for me to see it, and still not sure if what happened wasn't just my imagination. I thought that the chain moved very fast for an inch or two. Anyways, I watched how to video on timing the 3v, but I am very confused about it. The left bank seems to line up on timing marks perfectly, but the right chain is off by at least 2 1/2 links. Not knowing any better, I removed three rockers on left bank (2 intakes and 1 exhaust) but only removed two intake rockers on right side. I don't know what I am doing and getting scared.
View 1 Replies
Battery light comes on when the truck is running at less than about 1200rpm, but I see zero movement on the needle. Weird thing is i charged the batteries and tested the alternator with my multimeter and it was reading 14.1-14.2 which is nominal. Run it for about 10 min then it reads 12.3-12.8
I'm thinking a bad cell in the battery or alternator is going out. Oh and all the connections are tight, wires look good. 2001 f250 4wd 7.3 intake exhaust basic tuner gauges. Could the constant heat be a factor?
View 12 Replies
I have a 2000 f250 crew cab short bed 7.3 on a 6inch bds lift and 37 inch tires. When I accelerate pretty much any load above 1200 rpms I can feel a vibration, kinda feels like it may be coming from the front left but I'm not sure. I have heard that a wheel bearing going out can cause this, would this maybe be what's causing it?
I thought wheel bearing because it kind of sounds like there's a howl when decelerating, probably when accelerating as well but the trucks too loud and I can't hear it. or also have heard motor mount gone bad, I've also heard ujoints but the ujoints were done this summer. the front ujoint is bad but the front driveshaft shouldn't be turning when out of 4x4 and hubs unlocked.
View 4 Replies
I've got a 99 4runner with the 3.4 engine and it's gotten to where it wants to stall in traffic. It starts right back up. Runs fine on the interstate. No check engine light. I've changed the fuel filter, cleaned the throttle body, and cleaned the MAF sensor. Not sure what to do next.
View 4 Replies
I started "Hard Start at Operating Temperature" you can probably tell that 300k has done a number on my HPOP. I'm wondering what to do... do I buy a new pump from ford? Buy from ebay? Or is there a good pump rebuilder in the Portland metro area? I've heard they are almost impossible to rebuild.
View 6 Replies
I've got a 99 Ranger. A month or so ago, it started to be a little hard to start. It would turn over, but not fully start unless I gave it a little gas. This did not happen all the time, primarily it happened after it had sat all day when I left work. Not long after that started, my check engine light came on. The codes were for a lean mix as reported from the 02 sensors. Before I could dig any further, it just wouldn't start at all one evening. This was after I had driven it for 30min and then parked it for an hour or less. But this time it was different in that the solenoid would just click, but that was it, like it didn't have enough power to turn over. I took the battery to have it tested and it had been severely discharged.
I got a new battery as that one had reached it's limits. Put it in and the truck started right up no problem. A few days later it started acting up again like it had originally, I had to give it some gas to get started. I had the alternator/starter checked, both were fine. A day later, it got so bad that I had to shift to N and keep giving it fuel anytime I stopped the truck. I had to do this all the way to and from work. Now this morning I go out and it starts right up, no issues, no dying at idle and didn't have bit of problem coming in. Initially we thought it must be a fuel pump, but then I can't explain why it worked fine this morning. I changed the fuel filter less than 2 years ago, so I wouldn't think it would require changing already. Wondering if there's a sensor issue, one that calls for appropriate amount of fuel?
View 2 Replies
So, about 6 months ago, I bought a 1999 Dodge Ram just to keep around the house to do odd and ends jobs. Not a daily driver. I might have a need for it every few months. Well, a few months ago, I went to start it and the battery was dead. I have a battery charger that tests the battery. It said the battery was bad. So, I bought a new battery. A few days ago, I went to start it... again with the new battery, it was dead.
Put the charger on it and it said again that there was a shorted cell in it. So, I returned that one under warranty. Now went to start it, dead again (a week later.) So, I guess it's obvious it's not a bad battery (or at least the bad batteries are a cause of something else wrong.) I'm guessing there's a slow drain somewhere in the truck. How to find it?
I don't know if this has anything to do with it... Ever since I've owned it, every once in a while when driving the truck, all the gauges on the dash go to 0. Then it will just randomly start working again. Don't know if that has anything to do with the battery dying problem.
View 2 Replies
My issue is not with the truck starting its with it staying running. I had plugged in all the night prior and all day while at work. When my shift was over went out started fine let it run for about 20 minutes and left to make my way home. During the trip it ran fine for about 1/2 a mile and then it started idling really rough at a stop light went to go threw the light and it as though I had left it out all night with plugging it in. I went to turn on a side street because this situation was not going to end well and it died trying to turn. It would not start back up I was able to get a jump and made another 1/4 of a mile and it died right in front of my house. I replaced both the batteries this morning and it fired right up lasted about a minute and then died again. All the gauge read fine, oil level is good, and the injectors were replaced 2 years ago.
View 14 Replies
I have a 1999 f250 super duty and something keeps draining my battery, I replaced the old one and im having the same problem. What could it be?
View 14 Replies
My starter solenoid keeps dying. I can't use a retail chain part. They burn up in a day. Always Motorcraft and it only lasts a year or so.
Any way to test this thing to see why it burns out prematurely?
View 9 Replies
In the last 15k miles, I've replaced the led lights on my driver side mirror twice already, and come to see this morning: they are out again. The turn signal LEDs still work, but the parking lights don't work anymore. Passenger side is fine.
View 3 Replies
