Ever hear of a crank pulley failure? Mine did and took out the serpentine belt. I have 63,000 miles on the 07 and it was a big shock to see the pulley in two parts.
View 5 RepliesBeen trying to isolate my noisy serpentine belt. Had the belt off and spun everything, only thing I found that made any noise was the alternator. It had a nice churp like a bearing was on its way out in it. So I replaced that figuring my squeak was going to go away. No such luck. Listening to it again while it was idling, I crawled underneath. Almost seems like the churping noise is coming from the Crank Pulley. Is there a bearing on this pulley that goes bad?
View 13 Replies2006 6.0l ... I've read all over for tips on routing this belt and everyone plays it off as being some simple '20-minute' task. I'm on my 4th hour on this now.
I can't figure out how to route the belt around the tensioner pulley, circled in the picture (from another thread). Everyone glosses over how to do this and I can't figure it out.
It seems like the only way to get it on is to bend the belt and slide it between the pulley and the block, but that I just can't reach the blasted thing.
2002 Camry 4 cyl. Can the idler pulley alone be replaced on the serpentine belt tensioner? I noticed a very slight side to side play when I had the belt off. No noise from it. When I looked at rock auto, they sell the whole bracket with the pulley.
View 2 RepliesMy tensioner pulley is making noise.I replaced the rear idler pulley (can't get to the front one), but still have the noise. Mention a DIY for replacing the tensioner pulley bearing. A part number for the bearing?
View 2 RepliesThe nut that holds the pulley in place on the alternator has fallen off, causing the pulley to become loose and now the serpentine belt will not stay on. What is the size and thread type for the nut that I need to replace?
Alternator Pulley Nut for 2004 Camry 4cyl
I have 1997 F250 LD since i bough it has been doing this chirping sound coming from the serpentine belt and the pulley area but when the truck has been working for 15 - 20 min it goes away
This is apart from the from the problem before I think the fan clutch is broken because when I start the truck I can hear the fan going at the same speed of the engine is that normal ? even when the truck is cold
I am working with Honda dealership management because I had my timing belt changed at 102,000 miles and 25,000 miles later The belt broke and frayed while driving in heavy traffic at night on freeway leaving me stranded in the median luckily instead of in the middle of the freeway. Honda dealership stating that the idle tension pulley caused the fraying of the belt not due to poor workmanship by their mechanics. I am asking dealership to consider assisting in payment because the day the belt went out, the car had been serviced for a oil change.
When I was called to be notified the job was complete I asked the service rep questions about the oil transmission and told him there was a noise in the engine could they check it or did they check it which she replied no that I would have to make another appointment for that. So even if I would've made appointment the next day the damage was already done because that night is when the belt broke Is this part of Hondas responsibility is it reasonable for them to take part responsibility. Also if the idol tension pulley had been changed at the same time of the belt, it would've saved my engine. So this is all my responsibility not theirs?
I own a 2006 Kia Sedona which we bought brand new. Now after five years and 40,000 miles (we don't drive it much) it has developed a rattling noise by the top serpentine pulley. I am afraid this is where the timing chain is. I am not even sure if this vehicle has a chain or belt. Could either one of these be the problem?
View 15 RepliesSerpentine belt on a 2006 Honda Odyssey fraying and then ripping into the timing belt causing that belt to break? I recently had this scenario given to me as the cause of my recently replaced timing belt breaking.
View 11 RepliesOne of my belts squeaks. I've tightened one of them as far as it goes I think. The other one is the one with the alternator. Do I tighten the pulley bolt on the alternator to add tension to that one?
View 4 RepliesI've been hearing a slight squeaking near the belt area. It's not continuous. Does it for a second then stops for a second and continues.
I hear it a lot more when I put the heat on through the top window (defroster). Never noticed it until it started getting cold. You think it might just be the belt? Or what?
How to replace the belt tensioner. It's not putting out enough tension when the engine is cold. So, the belt makes chirping noise for couple of minutes idling when cold with AC on.
I had the AC inspected and everything checks out according to my mechanic.
He believes that the issue is with the tensioner since I had recently had replaced the serpentine belt.
I just replaced the original serpentine belt at 95k miles (more preventative than anything) and now it's squeaking. Does this mean I have to replace the tensioner?
View 11 RepliesIs it time to replace? There is a noise coming from the belt and when I listen with the hood up my best guess is that it's the tensioner. I'm not sure if it is easy to replace or if that is even the problem. The belt looks fine. It allows me to twist it barely less than halfway so to me it does not seem loose. But in the rain last week got the battery light and lost power steering, power brakes, etc, then it went back to normal and hasn't failed again since. The car has 131,000 miles.
Is there a way to check the tensioner? It's pretty tight in there. Or am I wrong as to what the problem is? The sound is a rubbing/slight clicking sound that is in time with the engine and you can hear it if you listen inside the car when the engine is on. The belt also seems to wander around on the tensioner just a little. One day it was about a mm in too much, a few days later, a few mm out, in relation to the pulley.
Speed, RPM gas and temp cluster are black. Wire and cluster contact fixed once each. repair lasted two months. Is it possible for an owner to get at the cluster?
View 4 RepliesI have a '06 sonata 3.3 v6. Let me first describe what was happening to the car before the noise started. When I first started the car and put the ac, the first time turning the steering wheel in either direction the steering wheel would tighten up and the battery indicator light would come on and the fasten seatbelt light would flash even though I had the belt fastened. It would only happen the first time I would make a turn and after that I could turn with no problem. So in recap, it would only happen on the first turn and only when the ac was on. Now when I start the car up there is a noise coming form the pulley/belt area. I wouldn't classify it as a squeaking noise more like a grinding. I've looked at the belt and it seems to be fine. After I start to drive the car the noise goes away. If I start the car again after a drive within about 2 hours the noise doesn't happen when I start it. What this noise could be? and also could the noise and the steering wheel tightening when the ac is on be connected?
View 1 RepliesIs it possible to change the water pump and serpentine belt in a 2006 Toyota Camry with 4 cyl. engine in less than an hour?
View 4 RepliesI have a 2006 Escape with a 4cyl. 2.3L automatic gas engine. Recently when going down the road my serpentine belt broke. I purchased a new one and attempted to install it. However, after routing it over all the pulleys there is still a significant amount of slack. Keep in mind when putting the new one on I didn't even have to move the tension pulley. Upon starting the vehicle I was able to see that all of the pulleys were moving and doing what was expected.
However, there is a great deal of squealing and risk that the belt with be thrown off or broken. I researched and am fairly certain that it is in fact the correct size belt as all the sites indicate the same part number and size. Could this be the result of a bad tension pulley that needs to be replaced? Need access to the routing diagram in case I may have put it on incorrectly? Am I missing some other form of adjusting the tension in the belt?
I have an 06 Azera LTD with about 40k on it. Recently the passenger power seat stopped working. Only going forward, all other directions work. Now the seat is all the way back with no way to move it up. Can't be a fuse, but maybe a loose connection?
View 4 RepliesPreparing for a timing belt replacement on a 2007 elantra. well aware of how to remove the crank pulley and do the job. My question is this : once you have the nut off, does the crank pulley come off by hand or is a puller required? came off nicely wiggling it by hand on any accent i've done, but never done this particular job with the elantra.
View 4 Replies