Azera TG (2006-11) :: 10 Amp Fuse For A/C Solenoid Blowing
Aug 29, 2016
Just this morning, my 2006 Azera Limited would not cycle on the A/C. I found that the 10 amp fuse for the A/C solenoid had blown. I replaced the fuse. The A/C worked perfectly, blew ice cold air, for about 15 minutes. Then the fuse blew again. Replaced the fuse again, the compressor clutch kicked and started to turn compressor and fuse blew yet again. Replaced fuse a third time, blew immediately. And now tonight, the dash lighting will not go into "night mode" - will not dim the instrument cluster fully, and the night illumination on controls will not light. Also, randomly, the fog light indicator will not light - even though the fog lights are on and illuminated. Not sure all these things are related, but it seems like some sort of major failure is occurring somewhere. I looked for shorted or burnt wiring under the hood, couldn't find any. Other than taking the car to Hyundai and paying two arms and a leg? I have seen posts for other Hyundai models where the compressor wiring shorts against the compressor - but so snug down there I haven't been able to check it properly yet. Also, another post suggested the clutch coil may be bad? But if it was, would it kick in and run properly for 15 minutes? I'm mechanically inclined, have done a lot of work myself on cars for over 20 years, but this one stumps me...
View 4 Replies
Advertisement
My 2006 Azera Limited keeps blowing its backup fuse (10amp) whenever I so much as move an inch in reverse. Moving from P to D (or even past the manual gate) is OK, as long as I don't take my foot off the brake when passing R.
I've so far burned through 4 fuses and still don't know what the problem is.
Here's some history:
The first time this happened yesterday AM, I just replaced the blown b/up fuse with the spare 10amp and the car ran fine the whole day, including several feet of reversing.
The second time this happened was today AM. I ran out of extra fuses, and decided to use the ABS (10amp) fuse instead, to be able to go pick up extra fuses at the local autoparts store. On the drive, I kept seeing check engine and ABS failure messages on the IP, as expected.
After I replaced the 2nd blown fuse, the check engine light came on. I didn't have my code reader with me (it's a funky bluetooth obd reader + android tablet, and i don't always carry the tablet). Had the local gas station look at the codes, and was told of "speed sensor" and a "high-speed controller link" error codes.
Reversed out of the parking spot at the gas station, and the fuse blew again. Twice.
Nothing on the car (other than as described above) has changed in the past several months. I haven't had the car washed for over 6months, but did drive in the rain several weeks ago. There haven't been any other changes at all (I opened the hood up just yesterday after several weeks of not needing to). The car is stock, there haven't been any major modifications (except, I removed an aftermarket nav system and put the stock 6cd radio back, but that was several months ago).
I'm pretty sure there's some sort of electrical fault somewhere, but can't quite figure out what / where.
View 12 Replies
My 2005 4.6L 4x4 screw is blowing the 10amp a/c clutch, 4x4 solenoid fuse whenever i turn the a/c on, at times whenever I turn the defrost on. the fuse does not blow when i turn the key to power (no engine start) but when engine is running fuse will trip. I disconnected elect. Connection at compressor and fuse still blows, also seems like no power or life from compressor.
View 3 Replies
The screen that you see the temperature and see the the way that the AC is blowing started flickering for some time now . It's an electric problem ...I guess . Maybe the fuse is going bad ? -06 Azera ....
View 1 Replies
I have a 2008 Azera, my A/C is not working properly, when I turn it on the drivers side is COOL, the passenger side warm air is coming out.
View 1 Replies
My 08 Azera blows cold air out the drivers side vent when everything on the right sides blows heat. If I set drivers side 88 degrees it blows some warm air. I changed the cabin filter and that did not work.
View 13 Replies
Yesterday My wife's 2010 Elantra needed a jump start, I had Accidentally connected the Jumper cables up incorrectly. I corrected the issue and the vehicle runs fine now. however the AUDIO fuse in the interior, which controls the radio and any alert Dings keeps blowing. Its a 15A fuse. I replaced it yesterday with a brand new fuse and it worked when tested the first time. this morning however it is now not working again and the fuse is again blown. do I just replace it with another fuse? is there something else I can check? will a 20A fuse work better?
View 1 Replies
I tried installing my new DDMTuning 35W 6000K HID headlights with relay harness. No issues until I went to turn the car on and actually power them up. Neither side would work. I checked my power connection, ground, in-line fuse, swapped out the relay, tried without the harness, and nothing worked. I tried putting the stock bulbs back in and I found out they wouldn't turn on either.
I found the issue to be a blown 20 amp fuse in slot 23 (see pic). I replaced it and tried to turn the car on with the HIDs and it blew again. I hooked the stock lights back up and they seem to work fine now with another new fuse. The fuse description says H/LP LO and HID LO LH. Why this fuse is blowing. I am wondering if I just need a higher amperage fuse because of the HID power (in line for harness is 30 amp) or if something else is the culprit. I'm stumped.
View 12 Replies
I got in my 2009 Sonata this morning, started it and turned on the headlights. The headlights turned on momentarily and then turned off. The 20 amp headlight fuse blew. I cleaned the battery ground on the fender and the battery terminals. I also cleaned the connection between the battery terminal connector and the negative cable. I put everything back together and installed a new 20 amp fuse. I turned the lights on. They lit momentarily and then, predictably, blew the fuse again. Curiously enough, the "passing lights",which are just the high beams on another position on the headlight switch, still work.
View 2 Replies
My left side blinkers keeps Blowing the fuse, I replaced ir 3 times already. First I thought it was the light bulb but my whole left side (driver side) blinkers were out except the one on the side mirror. Is there a relay for the blinkers somewhere that might be bad or something else?
View 2 Replies
My 2006 f-250 just started blowing the #22 fuse when i go over a bump! Where the wire harness is for this. I've checked all the harnesses I could locate that looked like they could be rubbing on something.
View 14 Replies
I have a 2006 f350 king ranch 4x4, I recently used 4 wheel drive and could not disengage it, it would go into 4 low but would not go back to 4 high or 2 wheel drive, I unplugged the actuator harness and applied 12 volts to the terminals and it disengaged, I reversed the power and it engages, the actuator seems to work properly, I then replaced the two relays located by themselves on the front fender driver side, when I try to install the 30 amp female fuse located in the outside fuse panel rear driver side, fuse #3 for 4x4 shift on the fly it blows immediately, it makes no difference if the harness is plugged into the actuator or not, if I remove the two relays then I can install the 30 amp fuse, but as soon as I try to install the relays it blows the fuse again..
View 6 Replies
I have a 06 Mercury Mariner and this past week fuse #26 keeps blowing turning the HVAC blower motor off. I replaced the blower motor since i had one already in the garage and same thing is happening. The AC will run for awhile and in about 10/15 mins the fuse will blow. Fuse #26 is the Climate control system mode switch, are these known to go bad? Is this the part I should replace or look for other problems IE compressor?
View 2 Replies
Anyways I have a 2006 F350 6.0 and a couple weeks ago I have been having issues with my running lights. In the fuse box under the dash fuse location 17 blows as soon as I insert the fuse leaving me with a short somewhere, no instrument cluster lights (but the instrument cluster gauges work and operate fine), and no running lights on the truck. I have been looking for hours and days and can't seem to locate this short (which I am assuming it is).
View 6 Replies
The fuel pump fuse keeps blowing intermittently. I would assume it's a wire grounding out somewhere but I can't seem to find one yet. I do have a faulty purge solenoid on the canister but I don't think that would cause this. The reset switch doesn't seem to be tripped either.
View 3 Replies
FUSE 38 Keeps blowing...it controls the fans and dealer is not sure why. Coolant fan control (FC) control Module.....
View 6 Replies
I have a 91 celica st and my efi fuse keeps blowing. i would like to know what the efi fuse controls, or what to check first.
View 3 Replies
2007 FJ Cruiser, 4WD, 65K Miles. I replaced the 120 AMP Fuse. Starts, everything seems to work, but the 40 AMP Fuse (ABS Motor) is blown. New fuses blow as soon as I place them in. Brakes pedal has little resistance and can barely stop the vehicle at slow speeds.
What will stop the 40 amp ABS fuse from blowing?
View 3 Replies
My 2000 Passat 1.8T is being evil again. Fuse 15 keeps blowing and I can't seem to find where the short is... however, its stuck at my work. Its a pretty big short, the fuse sparks as soon as I put the fuse near it. BIG SPARKS. Any way to start it without that fuse in?
View 1 Replies
Every time I step on the brakes, there is a bright spark in fuse #13. My brake lights, turn signals and hazards don't work. At this point my truck isn't drivable.
According to the owner's manual in my truck, says circuit #13 is for "stop lamps, CHMSL/hazard, trailer tow stop lamp, and speed control."
I'm assuming that the hazard part covers the turn signals as well, but I know the cruise control works even when the fuse is blown. I used it last night on the way home (this was before I realized I didn't have brake lights).
So I know I have a short somewhere. The only mods I've done to the lights are the aftermarket headlights, but if the fuse only gets blown when I step on the brakes, I don't see what that would have to do with it. Also, these lights have been installed and working for about a month before this started. The only thing that I did around the same time was install the gauges. I ran the power to them from #5, the customer access circuit.
Are there any other "common" areas for this to happen? I already removed the rear brake lights and it didn't work. I am quickly running out of 20A mini fuses.
View 5 Replies
Every time you engage the car in drive it blows a fuse. I have checked through the wiring but cannot see what the cause is.
View 14 Replies
