Avalon 2005-12 :: Various Misfire - Common Code P0301 Which Is Cylinder 1
Aug 31, 2015
'07 Avalon with 169k miles. I replaced all 3 back coils and 6 plugs back in December when I had various misfires, but the most common code was P0301 which is cylinder 1.
Car ran great until last week when I made a hard left and accelerated. CEL started flashing, read code and it's P0301. Every time I accelerate half throttle or more I can set the code off, but then shutting down car and restarting it drives fine, until I go half throttle. Car runs better when cold, and worse when I turn left and accelerate.
As long as I don't mash the gas I can drive for a half hour or so without the strumbling/hesitation. Surely the new coil hasn't failed so soon, I hate to pull the wipers, plenum,etc. and buy another coil just on a chance that might solve the issue. Car is only throwing a P0301 this time, no other codes like before. I've read a clogged cat or sticky exhaust valve could cause a cyl misfire.
View 10 Replies
Advertisement
I experienced a misfire code for #4 cylinder on my 2006 Toyota Avalon approx 8,000 miles ago and replaced the three front bank coils with Beck/Arnley coils. I didn't realize they were made in china until they arrived. The car ran fine until today when I got another misfire code for the same cylinder. I still had the two old coils in the garage so I swapped out # 4 and I'm happy to report that solved the problem. My question is should I be concerned that the # 4 cylinder has gone thru two coils in 8,000 miles or chalk it up to cheap chinese crap replacement parts?
View 4 Replies
My 97 F150 through a CEL Tuesday night P0301 so I picked up a new plug because it's cheap and simple, but that didn't do anything. Spark plug wires are about 3 months old, I also swapped injectors between 1 and 2, and misfire stayed with cylinder 1. It also gained a tap when the misfire started but only above idle, but it doesn't sound like a rod knock.
I also noticed if you unplug injector 1at idle it taps/knocks 3 or 4 times, however if you unplug any of the others it doesn't do that. I checked and I definitely have good spark from the plug. I plan on picking up a new compression tester tomorrow since mine never was returned. If you take the oil fill cap off it doesn't have any blow by at idle, however if you rev it you get a quick cloud out of it.
I thought about picking up a kit to check the injector pulse.
View 8 Replies
This happened xmas shopping with the wife. Started misfiring on the highway,took the 1st exit to find a garage as I am 20kms from home. The vibrations were worse at stop, but made it to a garage. They gave me the p0301 misfire cylinder 1, said they don't touch 5.4 plugs, told me to go to ford 2kms down the road. NICE. 4 in the pm, FORD dealer worse case scenario. Nope gave me a loaner told me come back at 930am. Truck was just waiting for an injector when I arrived. Plug & coil were good injector was shot,changed the fuel filter & oil change.
View 6 Replies
2009 corolla 1.8l 155,000 miles. Replaced iridium spark plugs at 100,000
I got a CEL few weeks ago, P0301 Toyota - Cylinder 1 Misfire Detected
Car has been running bad for about 2 weeks now, excise noise on the highway, especially up hills.
Yesterday, I took a look, replaced the spark plug in cylinder 1, same results. Checked the coils using one of those flashing tools, all 4 flashed quickly, with no breaks in flashing. put it all back together, cleared the code, went home.
Took it out for a drive today, and it started running way worse. Checked the CEL, and now I have both P0301 and P0303 Misfire on cylinder 1 and 3. Barely made it home, ran VERY VERY bad.
Got home, and made a video of it. It just kept dying. Check it out here. [URL] .....
Also, when it does run, it almost sounds like I can hear excess air, its hard to hear in video, but doesn't sound right. Maybe air leak? How do I check?
View 2 Replies
So I dropped my prius off to get looked at for error code p0301 number 1 cylinder missfire. They ruled out Spark plugs, coils and fuel injector. What else is ther? Also could it be the battery or even gas?
View 12 Replies
I am at about my wits end with this P0301 (Misfire On Cylinder #1) code on my 2003 Ford F150 4.6L. I've replaced the coil pack on that cylinder, all the spark plugs, and replaced the fuel injector on that cylinder. We keep clearing the code and it keeps on coming back.
The weird thing is that it only misfires after the truck has set for a few hours and then it only misfires when I first put it in gear. Once I am out of the driveway and on the road it's fine for most of the day unless I let it sit for several hours and then it might misfire again.
We noticed that the connector to the fuel injector is wobbly and doesn't snap tight to the fuel injector (before and after it was replaced) due to the clips on the side not working well. We zip tied it together this afternoon to make it fit tightly to the fuel injector to see if that works.
What could be causing this? Other than that misfire the engine sounds great and the trucks runs very well.
View 4 Replies
I have a 98 F150 4.2L with code P0301 Cylinder 1 Misfire.
This is what I have done so far. New plugs, coil pack, plug wires, TPS, EGR, EGR Vacuum control regualier, DMCP, canister, all of these parts are new and was bought from the ford place. Have taken the egr value, and egr value bracket off to see if carbon blockage was present, but it was clean. It was clean in the motor also. Have blown air through the metal tube that connects to the egr value and it come out the tail pipe very good, so no blockage their. Have cleaned throtle body and injectors. Have tested fuel injector with tester and it works correctly. Motor holder pressure. Have correct fuel pressure.
Do not have any vacuum leaks, it holds vacuum correctly. Crankshaft sensor is fine. Went throw 4 cans of break parts cleaner, spraying on intake while motor was running, motor did not idle up or change. I have done all this and it still shows code P0301, and it still skips. Here's the catch, if you unplug the vaccum off the egr the misfire goes away, or unplug the EGR vacuum control regulator it goes away, or if you unplug the DMCP sensor it goes away, it does not matter witch one you unplug, the misfire goes away.
I have had several different test done the the truck, but all the test only show that one code P0301, they do not show any other codes, or problem's with my truck.
View 14 Replies
I have a 2006 F150 with a cylinder #1 misfire only code p0301. I have done new spark plugs, new coil packs, and new fuel injector on cylinder #1 with no luck. What to do next?
View 5 Replies
I have a 99 Volkswagen Passat 1.8 Turbo Automatic AEB engine. I recently did a rebuild on it and ever since I keep getting this code P0301 that says "cylinder 1 misfire". The engine is also running rich and the spark plug in cylinder 1 keeps getting gummed up. I've changed the coil and the spark plugs and the injectors and it works temporarily but then the problem keeps reoccurring.
View 7 Replies
I understand the TSB for this issue relates to 2005 and 2006 model Avalons. what's your best guess in terms of how common the timing cover oil leak problem is on '05s and '06s? 20%? 80%?
View 11 Replies
Changed all the spark plugs and also new coils on the rear bank, drove car and the code 302 returned. Did not have the code while idling, code came up when started driving. Added lucas fuel injector cleaner to the gas tank. Curious about Seafoam and if I should try it and which method to use it by. I know it can be added to oil, fuel, or injected right into the vacuum hose from the brake booster. My wife's car and she is getting crabby.
View 9 Replies
What to do Misfire Error all cylinders also coil code P0356 . It is 2006 Avalon Ltd with 37,000 miles always maintained and all recalls completed. Is there something I missed or is this for real or could there be a common problem that is causing all the errors. Car idles ok and no problem driving below 60 mph anything over and you can fell a shutter like it will lose power.
View 14 Replies
2005 4cyl. Vue with 54K... Steady CEL. Runs great. Absolutely no problem accelerating. Don?t hear or feel any misfiring. There is a slight rumbling sound when I first start to drive the car, but to me, the sound doesn't seem come from the engine, but rather underneath the car. It goes away when I continue to drive. Since winter began, I occasionally feel a very slight hesitation during idle?happened once or twice lately.
Again, I only feel justified in mentioning it simply because of the codes that were generated. None of my passengers have made a comment about the idle or the drive. My friend, however, made a remark that occasionally, there is a very very very slight hesitation at the downshift when braking. No crack in gas cap. Great fuel economy. No problems accelerating at all. Never hear or an actual misfire, which I take it, means a problem when accelerating, a jerking, or popping noise.
Took it to a dealer. Codes were 0300, 301, 302, 303, 304?302 generating most often. Dealer recommended new ignition module and plug replacement, but they said it wouldn?t be a guaranteed fix and that it may need EGR replacement (don?t hear knocking though) or be a burnt valve in the cylinder. No suction out tailpipe, no rotten egg smell (signs of burnt valve). What are the chances of burnt valve in a car with 54K anyway?
Also, my maintenance schedule claims that I don?t need new spark plugs until 100K. Is there anything else this could be such as a dirty injector system, fuel filter, fuel pump, or air filter? Again, overall, the car runs GREAT! Should I just wait and see if the misfire becomes more pronounced so when I take it to a mechanic, they won't be looking for a needle in a haystack?
View 4 Replies
I have a 2009 Corolla with a 1.8 L. I have the misfire code P0301. I have changed the plugs, ignition coil, and fuel injector on cylinder one. It still has the misfire.
View 5 Replies
I have a 2009 Prius that I purchased 6 months ago and have been really happy with it until the last couple of months. As the weather is getting colder appears I have a misfiring problem on start-up
I have had this problem now for a little while and have been trying to get it understood before paying $$ at the dealer for "maybe" solutions.
It started as the weather got colder. Intermittently the check engine light would come on. Then after a few days would go off.
I have considered water in the line: fuel injection cleaner/antifreeze
I have considered bad gas in the tank: problem persists several fuel tanks later
I have recently purchased a trouble code reader/diagnostic that plugs into my laptop. Trouble code is p0301. Cylinder 1 misfire.
I have taken it in to the shop.They tried:
>>moving the ignitor coil from cylinder 1 to cylinder 4,
>>and also tried moving the spark plug from cylinder 1 to cylinder 2.
>>performed compression test. Ok
The dealer suggests replacing the injector line for $1400+.( They did this with warm engine. They have not diagnosed cold engine yet. That is new, read more,...) I still have 5K kilometers left on the power-train warranty. If it is power-train I would like it resolved before warranty expires.
Now. Some new info as of yesterday:
Up till now I was not using the diagnostic monitor real time. but that started yesterday,... Last night when I got home from work while the engine was still warm I connected the diagnostic monitor and went for a drive. Every few minutes I would pull over and refresh the cylinder misfiring data. I had hardly any misfires across all the cylinders at all. Maybe 1 or 2, here or there over the span of a 10 minute warm engine ride. Up and down hilly terrain. Nothing that came close to triggering the p0301 trouble code. I parked the car outside and let it rest overnight.
View 19 Replies
My 5.4 F250 with 200,000 miles having many problems... It all started a few months ago, when the cam needed to be replaced, and a cam phaser was also replaced at the same time. It ran fine after, then threw a code for cylinder 3 misfire. The guy I took it to said it was due to the huge crack in the exhaust manifold and that was messing with the o2 sensor coming up as a cylinder 3 misfire. So, got the new manifold and it was good for a few weeks.
Now, starting the other night, Friday the 13th, it threw a CEL when I was coming into the driveway. It had been throwing a code every once in a while, and I brought it to school to scan it Friday the 13th but there was no code. So, I assume that it is an intermittent problem, no big deal. When I go to get in my truck to go to work a few hours later, the 5.4 cranks... and cranks... and cranks.
I get it to fire up, and it dies again. Run codes, and it says that the cam positioning sensor is broken. Replace both of them, still acts up ie. doesn't start when it does start it runs very rough and stalls. Get it up to my uncles shop, and replace fuel filter.. Still runs like trash. Run codes now, and it says rich/lean in bank 1.. My uncle tells me to move my truck out of the shop, so I start it up, and it runs great. No hiccups, it idles perfect as I move his truck out of the shop first.
I park my truck outside and let it idle for about 10 mins, and when I come back out it is still idling, perfectly fine. I get in, put it in reverse, and get about 20 feet when it dies and will no longer start back up. What could be going wrong?! Sick of throwing money into this thing! At one time while started up in my uncles shop, it was blowing black smoke, as if it was a diesel!
View 10 Replies
My wife's 03 Passat w/ 1.8t is bucking and lurching throwing a P0301 (Cyl 1 misfire) code. We have about 58k on the engine and had the dealer do the 40k service 2 years ago.
So far I replaced cyl 1 spark plug, swapped and then replace coil pack with new. My choices for parts were limited on a Friday night and these are el cheapo Autozone parts. Still missing and throwing DTC, I don't really have access to Vag-Com anymore (just OBD reader at parts store) and I don't have a Bentley's either (I know there's some eye rolling going on now).
How to troubleshoot the cause so I can make a decision to take to mechanic or do a few more parts swaps between now and Monday. I've got tools and a multi-meter. I used to have Vag-Com but it isn't supported on my new laptop (Vista), I tried the USB extension cord on my desktop but it is hit and miss.
View 3 Replies
I had a consistent misfire on this car and finally got a P0301 trouble code. I installed new Autolite AP 104 plugs and wires. Now, when I start the engine. it runs perfectly. But when I put it in gear, it misfires. After a minute or so, the misfire clears and the engine runs perfectly. I have not received another trouble code. One thing I did notice is that the plugs I took out (Motorcraft AWSF 32P) had a much larger gap than the .044 the associate at AutoZone set the new plugs to.
View 7 Replies
I just bought a used Toyota Avalon with 135,500 miles on it. They sold it because it was smoking and didn't know what was wrong with it(they were an old retired couple). They were the only owners and it has never been driven hard or abused.... Anyway. I read online that unhooking the vacuum hose from the pcv valve may make it stop smoking. I unhooked it and plugged the vacuum hose and they were right. It stopped smoking after I got the rest of the oil out of the hose. I thought maybe the old pcv valve was messed up so I got a new one and hooked it back up but then smoking was back. So I am getting too much blow by in it for sure. I don't think the valve seals are leaking because as soon as I unhooked the vacuum from the pcv valve the smoking stopped. I drove it for 2 days with no smoke whatsoever. What could be causing the blow by to be so strong? It was strong enough to spit oil out of the pcv valve without the vacuum hose sucking it out(there was oil on the engine).
The check engine light is also on so I hooked it up to a computer at an auto parts store and it said I had a misfire on 2 cylinders(2 and 6). So I changed all the spark plugs and re-hooked it to the machine. This time I only got an error code for cylinder 2. Each plug has a coil so I switched the coil from cylinder 4 to cylinder 2 to test if maybe the coil was bad, but it still gave me a misfire on cylinder 2 only. I even swapped the plug from 2 to 4 to make sure the new plug wasn't bad. Still a misfire on cylinder 2. It is still smoking(ONLY WHEN VACUUM HOSE IS ON PCV VALVE) and check engine light is still on and error code says cylinder 2 misfire.
View 19 Replies
I am having a misfire code on the #1 cylinder. Its not bad but I really want to nip it in the butt before it goes out completely. I was told to try and get some of the older style coilpacks that bolt on and go with them. Can I put them on my 03 passat 1.8t.
View 2 Replies
