The other day I disconnected battery, then removed and cleaned the throttle body. Now cold-start idle is high, and erratic,
goes to 1,600, drops to 1,000
- back to 1600, drops, up to 1,400
-- wavers there, and then finally,
starts to taper down to steady idle of about 650-700 rpm.
Since battery disconnected, does not seem there would be a chance for TB to "un-synch" with cars computer.
I recently cleaned the throttle body and now it surges up and down. Not really sure what to check next. 2002 toyota camry 4 cyl.
View 3 RepliesI cleaned the MAF in my 2008 (58k miles) with CRC MAF cleaner and cleaned the throttle body as well. There was a small puddle of oil in the intake manifold from the previous owner overfilling oil so I cleaned that up as well.
View 19 RepliesTook my car in to get the tire and headlight replaced. Not my usual mechanic. While they were in there, they took it upon themselves to open up the filter and root around the throttle body. They said it was heavily gunked up, and asked to clean it. The car has been having serious starting issues, so this made sense to me, so I overlooked them examining a part of the car that had nothing to do with what I'd asked them to repair, and told them to go ahead.
Mechanic cleaned out the throttle body. Now he says there are scratches in it, he suspects from a mouse or rodent. Says it needs to be replaced, but he couldn't source a part today. Either way, I can't afford that. Says it's fine to drive, though.
Whatever they did, the car is now worse. Engine revs up high in park or when I start the car, and then drops dow and keeps revving rhythmically while idle. And I swear that while in drive, it's running faster even with my foot off the gas, and not dropping out of higher gears as fast. I go back and confront the mechanic. He says yes, that's all because of those scratches. But I don't understand how before, when it still had these scratches, WASN'T clean, when it was, in his words, all gunked up, it was working BETTER than it is now, when it's clean and just has those scratches?
I have a 2004 V6 LE with about 135k miles. I cleaned the throttle body two weeks ago, just because I hadn't ever done it. It wasn't too dirty. Before the cleaning, it idled at < 1k revs. Now, when I start the engine cold, it revs at around 1500, sometimes higher. It goes back to normal after the engine warms up to operating temperature.
Also, I hear a very slight high-pitched whining (maybe hissing?) noise when I accelerate. The noise is more prominent when the engine is cold. I checked for vacuum leaks but couldn't find any.
It feels like I'm depressing the gas pedal a little bit when I have it in drive or reverse, and it wants to pull harder than usual. When I bring the car to a stop with light brake pressure, as it drops into first gear, the car gives a slight tug forward, again, as if the gas pedal is depressed. I mention this to show that it's not just an issue with the rpm at startup.
I suspect that the issue lies with the throttle position sensor, which I may have jostled when I moved the throttle valve. The method I used when cleaning was, I first tried opening the valve by hand with the ignition off, but the resistance was much higher than I had anticipated. So I did the key-in method by turning the ignition to ON and putting a brick on the gas pedal. There was a high-pitched whine coming from somewhere in the engine bay when the key was ON, which I had not noticed before; I wonder if that is normal.
This seems to be a rather common issue after cleaning the throttle body cleaning, but there doesn't seem to be any consensus solution besides to wait it out.
2002 Camry XLE.
I cleaned my throttle body today. Since the throttle plate moves by a motor, in order to keep it open, I turned the key to ON and held the gas pedal down by using some weight.
After I put everything back, the idle was high 2000+, then stays at 1300 to 1400 range. I drove about 10 miles and it is still the same. When stopped at a light in drive, the idle is still 1000
Did I mess up the e-throttle or the throttle position sensor? (Since I used a weight to hold the gas pedal down, I am worried now).
I cleaned my daughters throttle body on her 2005 prius. Sprayed it down on the vehicle trying to fix my P0505 code and now its idling high. Is there a learn procedure to reset this after service.
View 6 RepliesJust took off the throttle body of my 2002 GT to clean it. Had all of the sensors off (IAC, MAF, TPS). Put everything back together and it fired right up but immediately went to 3000 rpm and acted like it would keep climbing.
Thought I was very careful putting everything back together. Obviously the throttle is open but there is no play in the throttle cables. Could it be a sensor?
High mileage 1999 4.6 4wd 5 spd: Needed to replace the rear ABS sensor and decided to clean the throttle body too while the battery was unplugged. Cleaned it around the butterfly and not much else. Truck idled at 750 BEFORE cleaning the TB. Now it fluctuates between 820 and 950 rpms. Also tends to stay at a higher rpm after pushing in the clutch and taking it out of gear.
Did a thorough check for vacuum leaks, nothing. After research, I cleaned the IAC and re installed (battery was disconnected then too). No improvement. Unplugged the IAC while running- ZERO change in idle. Installed new IAC, no change whatsoever. Unplugged NEW IAC, no change whatsoever. Is there an issue with the PCM needing time to fully re learn? Am I missing something.
08 Accord. After replacing the starter and cleaning the throttle body I keep having a CEL and the P0507 code.
Checked for leaks around intake, vacuum lines, etc. found none.
Tried the relearn procedure and still no luck. Car idea higher than normal ( just over 1000 rpms warm). Also feels like it wants to pull even when stopped.
So I figure I have either:-damaged the throttle body somehow cleaning it- Have incorrectly implemented the re learn procedure- missed a vacuum leak ( possible but doubtful)- or something else I don't know about
2002 mercury grand marquis high vibrating air pressure is in the throttle body it become louder with the more gas you give the car.The vibration is the worst in the idle speed control.The vibration extend all the way down to the air filter.The air filter is not stopped up.The noise use to come and go and the car would cut off at a idle.
View 1 RepliesWhere can I get body side moldings for an 09 Avalon.
The door sides are quite exposed to door dings...
97 Sierra K1500, 5.7 liter. High pitched whistling sound underhood in the vicinity of the throttle body. Starts after truck warms up and quiets down when accelerating. I've wiggled hoses, disconnected what I could without stalling engine, checked air lines into throttle body, checked air filter, etc. Sound does not change when I apply brakes so I don't think it's related to master cylinder. The only time it changes is when I accelerate, then only gets quiet until I come back to steady speed.
Truck has 85,000, runs great. No codes.
2002 V6 Camry 145,000 miles, cleaned throttle body with TBC fluid, now starts runs for a few seconds and dies. In order to open the butterfly in cleaning I turned ign on and propped pedal down. After cleaning the car ran better but idle was high and a little erratic. I disconnected the neg batt for several hours, now it starts, but dies right away. In the cleaning process I had removed the throttle control sensor an reinstalled it. Can't keep it running long enough to adjust it.
View 8 RepliesHaving problems with a ECM and throttle body for 2010 Corolla S? My corolla will idle rough and the throttle body will shut the car down to where it is inoperable. It throws codes and shuts the VVT down. The car currently has 56k miles on it and has been to Toyota 3 times in 3 months.
The first time they say they replaced the ECM, I really don't think so. 24 hours after we picked the car up it shut down again. The second time we brought it back in they said the brake light bulb caused the throttle body to shut down.
It had to go back again this week after it shut down again in traffic when it was idling. Toyota said the throttle body had to re-learn the idle again from when the ECM was supposedly replaced.
I have a 2009 Camry which has the well known very bad vibration at idle when in drive at a light. My Ultragauge shows the RPM are very low when it vibrates. Sometimes it drops to around 425-450 rpm when at a stop light in drive (automatic car). Then it sometimes moves up to around 625-675 rpm and that is when the vibration completely disappears and it is nice and smooth. This issue is intermittent but happens everyday.
Most people think it is due to a bad engine mount and spend money doing that and get no results.
I have done a lot of research and feel it is due to a dirty throttle body and IAC valve and want to test my theory. I will post results once I do the job. What is the easiest and most thorough way to clean both?
So I'm at my wits end trying to locate (and fix) a loud, high frequency rattle noise inside the engine compartment.
It can be heard when applying the gas pedal a certain amount. In other words, I can "find" the noise and maintain it at a certain rpm.
The noise is coming from the back of the engine near the firewall. It feels and sounds like it's coming from the throttle body plate and vibrating the gas pedal. I cleaned the plate and it isn't loose.
The issue doesn't seem to be affecting engine performance.
The sound is noticeable while driving (under load). When in park, I can find an rpm where the throttle body seems to take a heavy wave of vibration from the engine and hum (but not nearly as loud as while driving). Issue existed before I put on new motor mounts, and still persists after replacing all 4 (although the vibration and noise are reduced).
Few weeks ago.....Prius was showing the P0505 code .... Mechanic, ran diagnostics and determined it was dirty TB. Cleaned TB.....cleared the code (inspected PCV...hoses).
When I initially picked it up it was revving very high....so he hooked it back up to the scanner and did some type of "reset" for the idle (this cleared most some computer settings...back-up beep, radio stations, etc...). Everything ran fine for past 3 weeks...
Just last night..... started running rough again. What I noticed this morning ... Started it up and it ran very rough til the auto shutdown after warmup (no warning lights). Then....when I started driving slowly out of the lot...it ran "rough upon acceleration"...... Then fine at cruising speed. Same behavior at every light....rough acceleration.... fine once up to speed. Just started it up again and same behavior.....(does not die...just very rough).
I bought a 2009 f150 5.4 with 150000 miles on it. I have a slight hesitation from idle so I want to clean the throttle body. I found several for the older f150"s with the horizontal throttle body but this 2009 has a vertical mounted one. I change the air filter and cleaned the MAF but didn't change anything. My wife's ford 500 had this problem and cleaning the throttle body completely cured it.
View 3 RepliesTrying to clean the throttle body on my 09 sonata 2.4L due to rough idle occasionally (throwing P0106, replaced MAF sensor still same problem), one quick question, is it okay to force the valve open (with connector disconnected of course), and is "re-learning" necessary and what's the proper way to do it?
View 2 RepliesCarburetor: Autolite 4100
Fast Idle Speed: 1250 RPM
Curb Idle Speed: 600 RPM (At normal operating temperature)
When I cold start my truck, the fast idle speed holds the throttle at 1500 RPM. I will let it idle about 30 seconds or so, and then I will tap the gas to bring the idle down.
When I do this, the idle will immediately drop all the way down, and too low for a cold engine. The engine won't stall, but it will hover just below 500 RPM, which is a bit too low to idle smoothly.
But when the engine is at operating temperature, the idle speed is 600 RPM and the engine will happily idle smoothly.
Shouldn't there be an "in between" speed? When I tap the gas pedal at 1500 RPM to bring the idle down some, shouldn't the speed drop down a little lower, like 1000 RPM since the engine is still a bit cold?
If so, what do I need to adjust? The Autolite 4100 works PERFECTLY otherwise.