Aurora :: 1995 - High Mount Brake Light Not Working
Mar 4, 2006
Someone mentioned to me this week that my high mount brake light was not working. No big deal, just a burned out bulb I assumed. Well, I replaced the bulbs (two bulbs) and it still does not work. The sockets look fine, no corrosion. The wiring that I can see looks good. I used a volt meter & found I'm getting no juice at the socket . . ? Is there an in line fuse or something else simple I should check. I'm thinking this should be an easy fix & am frustrated I can't figure it out. By the way, my lower brake lights are working fine.
View 3 Replies
Advertisement
Trying to replace the burnt bulbs. Did the obvious: removed the two screws but in no way could I take the red lens off. I pried hard almost broke it but it's not coming off. It feels like some other mechanism holding it down. It is the one on top of the lift gate. The inside is just a hole with wires going through. What's the trick?
View 12 Replies
2010 F-250 14,000 miles, gas engine with Knapheide utility bed. Tilt wheel has been kept in the up position from day 1.
The problem:
No rear brake lights.
No high mount brake light.
No rear turn signals.
No rear hazard flashing lights.
All trailer lights work.
All other truck lights work.
Things checked: Fuses all OK. Visual inspection of multi-function switch. Looks clean. Brake switch at brake pedal has power on one wire. Jumpered the other wire-no brake lights.
I need to haul my trailer and am nervous when I see a Savannah, GA metro police car.
View 8 Replies
Can this be changed easily by a non-dealer? The local Autozone doesn't list any replacement bulbs or assemblies, and I can't see a simple way of accessing the light assembly from the trunk.
View 1 Replies
My wife's 2010 ES 350 third brake light has an intermittent LED issue. The last 3 LEDs on the pass side flash on/off when the brake is depressed. My understanding is there may be a broken solder joint. My problem is I can't seem to get the assembly out. How the high mount assembly is mounted and how to remove it?
View 2 Replies
Just bought an 02' camry and the high mount brake light on the spoiler is half burnt out. Tried removing what I'm guessing is an LED assembly but the screws are stuck and the angle is really awkward. Am I going to have to replace the whole LED bar?
View 2 Replies
Recently I noticed that three LEDs in my 05 SantaFe's high mount stop light glow even without the brake applied. When the brake pedal is depressed, the entire light glows as it should. But only the three LEDs glow at all times.
View 13 Replies
My high mount break light works sporadically. When I break, sometimes you can see it as bright as it can be, other times it is dim, and then sometimes no light comes on. The dealership could not even figure out how to get to the led unit.
View 8 Replies
Lexus has diagnosed a ground fault with an intermittent connection.... I am not sure how to proceed ... Could it be a light bulb connection... or does it even have these? Can the part be serviced in place... or must I replace the whole assembly?
View 4 Replies
1995 Aurora Remote entry fails. Keys were in pocket and I got wet while surf fishing... It worked last night coming home but this morning it fails to open doors or trunk.. I checked batteries,, 3 volts each... Did I short out the unit?? How can I check that out and if so, other than a dealer where can I find a new remote entry device...What has to be done to the unit to tune it to my car..
View 13 Replies
I cannot control the windows, locks, trunk or gas release from my 2001 Aurora. The fuses are under the back seat, which I took out. I checked the Drivers door module and the fuse is fine.
View 1 Replies
I have a1994 Dodge 1500 Ram Hemi extra cab 4door. The brake lights on the bed of the truck not the high light will blink on and off and sometimes stay on the other day my son-in-law narrowed the truck and a trailer and the trailer also blinked but again not the high light. Also the cruise has stopped working about the same time this started. At one time it was infrequent now is most of the time. Wondering if it could be part of the alarm system or something else it is driving me crazy.
View 4 Replies
1995 Cadillac DeVille 4.9 L Check engine soon light comes on, battery voltage high. When I increase speed the head lamps get brighter when I decrease speed the head lamps get dimmer. I changed the alternator because that's what a mechanic said I needed but I still have the problen battery voltage high. Will this damage the battery or other components? Should I stop driving the car.
View 5 Replies
I have a '95 Aerostar where the two lights are always on. I'd like to pull the codes if i can. Does this year has the RABS or the RABS II module. Or is the diagnostic connector the same?
View 14 Replies
Power door locks on my 2001 Aurrora have stopped working. It seemed to progress. First the rear door locks didn't work, now the rear and passenger door locks won't open or close with key fob or power switch on doors. I can still operate the door latches manually with the door lock lever. Also the interior lights and power windows to these same doors don't work. I examined the fuses under the rear seat and found nothing blown. What controls all these devices? The driver door operates as normal.
View 14 Replies
My wife's '98 Aurora, she said she heard a loud click and suddenly lost the heated seats, tach, speedometer, fuel & temp gauges, DIC, and climate control. I check the 60A fuse under the rear seat, it was OK. Replaced it with another 60A, no difference. Everything else electrical is still functioning.
View 1 Replies
1995 Lumina LS 3.1L w/ ~185K mi
A few weeks back, the amber ABS light would periodically illuminate and then became more frequent until it was On every time I used the car. The light only comes on after driving the car forward ~10-20ft. Recently in the past few days, the red brake light also started coming on at the exact same time as the amber ABS light. I can start up the car and idle, backup, and then as soon as I drive forward 10-20ft., both lights simultaneously illuminate, along with the sound of something that is engaging/closing/switching etc. coming from the front driver's side, maybe where the brake module is located. The sound coincides with the illumination of the lights. There is also absolutely no noticeable difference in braking.
I just changed the oil a couple days ago and the fluid level was good and appears to have not moved at all since I flushed the lines ~2.5yrs. ago. I cannot recall if I returned the pistons to the home position back then, but either way I was able to bleed all 4 lines.
What may be causing both lights to illuminate together when the car moves forward in addition to coinciding with a sort of clunking/engaging noise coming from the front driver's side?
If I have to replace the EBCM, then do I need a scan tool?
I already called Module Master and they do not rebuild any GM EBCMs built before 1999. Looks like Rock Auto has some though.
View 11 Replies
Just bought this wagon with 80000 miles. AC just stop working, fans and all. At the same time check engine light came on. Is it worth fixing or will I be facing thousands of dollars for furture repairs for this year car?
View 14 Replies
I just bought an older 1995 Ranger XLT 4.0 I was told that the truck is stuck in overdrive. The overdrive light is not working and the button does not respond. It shifts smooth but run away with it's self. It is not shifting a lot going up hill and curves.
I got a diagnostic and it did not show codes. I was told the trani has had an oil change and filter with no metal parts in the oil. Since the overdrive switch is know for a short in the steering column maybe when they looked at it they did not know what they were doing.
I am driving it only once or so a week. But don't want to hurt it. A friend did the first work and had it diagnostic done yesterday.
View 14 Replies
I have a 1995 Chevy k1500 Silverado Z71, I am having problems with my tail lights where when my headlights are on and I hit the breaks the driver side tail light completely turns off, if I use the left blinker it blinks very fast up till I hit the breaks. When my headlights are off they still don't work properly but legal enough, the left blinker blinks in between fast and slow and when I use the brakes the left side works but very dim, the wiring is all original never tampered with, all I did was put aftermarket tail light covers on it which shouldn't affect anything. The problem usually comes and goes but this last time it lasted for 2 months and now everything works perfect, the problem will be back and I'm afraid I'll run out of luck and a cop will finally notice it.
View 5 Replies
My Ranger, an '04 Edge without cargo lights. The high mount stoplight is faintly lit with the parking/headlights on. I had changed out the incandescent bulb for a LED, and went out to see how everything looked after dark. Well, the high mount had a slight glow to it, not really on, just a faint glow. This was never noticed with the regular bulb. I suspect I may have some stray voltage coming from somewhere, just enough to make the LED glow, but not enough for the normal bulb. When I switched off all the lights, it went out as well.
I tried to find a wiring diagram on line, like I've suggested to others in the past, but no luck from Autozone, or the EBSCO host I've used before. In fact the EBSCO will no longer accept "tech" as a user name or password.
So, where the problem may lie? I hate it when I can't figure out something like this!!!
View 6 Replies