Audi - A4 :: 2001 - Misfire On All Cylinders And Car Appears To Be Running Lean
Jul 19, 2011
I have a 2001 Audi A4 1.8t (AWM engine, B5 platform). When I start the car, I get misfires on all cylinders (very rough idle, sometimes it stalls when the engine is cold) and the car appears to be running lean. Once the CEL comes on, it runs fine (albeit the slight loss of power do the ECU going into limp mode to correct the problem).
So far, I've done the following myself: new O2 sensors, new SAI pump, new EGR valve, new diverter valve, new N75 valve, new vacuum hoses, cleaned the throttle body, new MAF sensor, cleaned the air filter, new plugs, and new coils. When the problem persisted, I had my mechanic change the timing belt, check for vacuum leaks, change the valve cover gasket, replace the fuel pump and filter. None of this has solved the problem! This is driving me nuts.
At this point, there are only two possibilities that I can think of:
1) Catalytic converter is clogged? I pulled out the pre-cat O2 sensor, started the car, but it still misfired. This seems to mean that there's another problem (i.e., if the cat is clogged, it's in addition to something else).
2) Dirty fuel injectors? I've put two bottles of Techron through the car to no avail. From the outside, they look pretty dirty, so I'll definitely try removing them, cleaning them, and replacing the gaskets. Hopefully this solves it.
Is there something I'm missing?
View 7 Replies
Advertisement
I am getting the dreaded emission workshop.
The codes i am getting are p0301-p0304 and p0171
Which are misfire on 4 cylinders and system to lean (bank 1).
Here is what I have done:
Got the 4 ignition coils replace, replaced the mass air flow, replaced the air filter, replace the plugs.
I just check the L wire and it doesn't have any cracks or holes
I don't know what to do next.
View 4 Replies
I have a 99 ford ranger xlt 4.0 ohv basically it sputters so bad while driving it sounds like a dump truck but it all started when I changed my o2 sensors but in doing so I broke my heater control valve and when I was going down the road it started sputtering well it started sputtering so I checked the o2 sensors there good and I changed the heater control valve. But nothing so I changed my coil pack spark plugs and wires but still nothing. But on my reader it says cylinders 2,3, and 4 are misfiring and bank 1 and 2 are running lean plus it has a bad aroma of gas in the engine compartment but when it idles its somewhat smooth but when I'm driving it its horrible the sputtering is so bad it takes awhile to get up to speed plus I'm only getting 100 miles to a whole tank that's like 8 or 9 mpg I need to fix this soon. This is my only transportation...
View 11 Replies
I have a 2001 1.8T Passat. I bought it used recently and have had tons of problems. I have been getting a lean air code for some time now and I think I recently resolved that. I had to replace a few vacuum lines, MAF, exhaust flex pipe (it was broken), fuel filter and fuel pressure regulator. The car was still running bad and throwing a lean air code (Bank 1) so I finally changed the O2 sensor and I think that did the trick. Now every time I start the car I get misfires until is warms up. I get misfires on all cylinders along with the multiple misfire code.
View 5 Replies
So my daughter's 2000 Golf Mk4 with 160,000 miles on it was running rough and had 3 codes stored - cylinders 2 & 3 misfire and a 411 secondary air injection problem.
Having had the misfire code before I swapped injectors around and the error code moved cylinders with the injectors so I attempted cleaning them and also cleaned the throttle body and intake manifold. At this point car still running rough but also started smoking badly.
Replaced the following items:
- Spark plugs
- Spark plug wires
- PCV valve
- PCV hose
- Fuel injectors w/ remanufactured
Hose reconnected between secondary air injection pump and air intake - previous owner had duct-taped it in when he couldn't get it to seal I guess. I've never heard it run.
Car running better, idles more smoothly, doesn't stumble or stall like it did before, no error codes coming up BUT car smokes a lot and the fumes make me feel sick just driving it a mile.
The car had never smoked like this before, hasn't had a whole lot of love the last year or two but no real problems either so why the sudden smoke?
At first I assumed it was cleaner being burned off but that should have been gone in under a minute and this is on-going. It's bad enough to not only be embarrassing but apparently dangerous as the fumes are bad.
View 11 Replies
I bought an 05 elantra for my daughter's first car. 47,000 miles.
I noticed every time the fan is on, the a/c appears to be running (as evidenced by cold air, clicking on and off of the air conditioner, draining of the system onto the road after shut down, etc.). Even with the a/c light off, it's clearly running. Could it be the switch or relay?
View 9 Replies
I have a buddy at work who has an 04 f350 6.0 that is running very rough. we put a scanner on it and disabled the injectors and 1,7,8 have no change. He checked the FICM voltage and is getting 48 volts on crank and run. He checked the wiring for anything loose or rubbed but nothing seems wrong.
View 14 Replies
Recently replaced plugs/wires on soon-to-be 10 year old '04 SF 3.5L (157K mi.) for the first time.
Plugs were OE Champion Platinum and all 6 looked identical except for excessive gap of .010 +/- due to all the miles. Replaced plugs with same as OE. Old plug wires looked good, but replaced them with aftermarket wires ( fit was as good as OE). Also replaced plenum gasket.
Problem is: engine runs rough at idle and high rpm and appears to be mis-firing. CEL is off and code reader shows no Trouble Codes stored.
View 19 Replies
Toyota read the codes wrong and told me that I need a new hybrid battery. That is incorrect info. Codes P0300 P0301 P0302P0303. The codes mean misfire in cylinders 1 , 2 and 3. I have had injector cleaned in the past new spark plugs. If I drive it it gets warmed up and shuts down. It will restart and run maybe 7 more miles the same. The brake light comes on and I have to restart it.
View 9 Replies
Friend of mine has a 2001 Elantra, not sure of the mileage but it started running really rough, like it's on 3 cylinders. His mech wants to look at the head, thinks there's a broken spring or something.
I asked if the timing belts ever been changed, no it hasn't. My suggestion is it might have lost a few teeth from the belt and jumped. I can't see it being a broken valve spring or something worse because the beta engine are tough as nails.
He said the wires are fine, they probably need replacing too because my friend is the type of person who changes oil and that's it.
View 2 Replies
I picked up a really cheap Hyundai Elantra 2005 that the kid that owned it really beat up on. Right now I am trying to sort out the issues so that it can become my daily driver for the next few years.
Second issue, The check engine light is on and it is popping up a P0171 generic engine running too lean code. The car looses power sometimes and I can smell gas in the car. I have a friend that is going to be loaning me his MAC code reader so that I can see if it is one of the O2 sensors and if so which one tomorrow.
View 16 Replies
2001 Santa Fe with 2.4 engine auto FWD 198k miles. When it is started first in the day, the engine sounds good and shifts well. After a few minutes and also after stops, first gear works well but then the following gears do not work well almost as if the engine and the transmission quit talking to each other. Traveling at 60 mph starting up a medium hill, the car downshifted and could not pick a gear. Although I pushed the pedal harder, the car did not respond rather continued to slow down. It acts like I lose 2 of the 4 cylinders in all cases. I replaced the spark plugs and two of them had oil on top of the plugs and also all around the threads. I replaced both coils thinking that one of them was the issue but no change has been observed. I replaced the throttle position sensor; no performance change. I do not believe it is the transmission as I have not notice any clunking, or bad shifting when starting out. While coasting at 40 mph in neutral and my pedal pressed at a certain position, the rpm gauge fluctuated from 3k to 3.6k many times for the duration of 20 seconds.
View 2 Replies
Bought a fixer upper 2001 v10 and it's definitely not running on all cylinders. Also the check engine light is not on and the PCM is not saying it's on (per my code reader) and it doesn't come on when I turn the key on.
Is it possible the previous owner had a programmer of some sort to disable the CEL? If the bulb were removed my scan tool would still show it on. Trying to get it to tell me which cylinders I am having trouble with.
View 6 Replies
2003 Ranger (4.0 L-2wd)...
Codes - random misfire and cylinder banks 1, 2, 3, reads out lean fuel
Will be checking out injectors and rail pressure, however, trouble shooting in general for this issue.
View 7 Replies
My Santa Fe driving me crazy. Have a 2002 Santa Fe 4 cyl with a problem. It will start when cold and run normal about 2 minutes. Then it starts running erratically like a misfire. If you let it idle this way it will stall quickly and not restart until totally cold again the next day. If you catch it quick enough and continually pump the throttle it continues to run rough until it starts to warm up. As it warms up the engine slowly improves until it reaches operating temp. At this point the misfire is much less but still there. If you shut it off for more than 10 minutes it will not start until the next day. There are no codes at this time. I have changed the coolant temp. sensor, the cam position sensor, fuel pump and screen, spark plugs and wires. I have also verified all timing marks on the crank, cams, etc. The crank sensor was replaced about 40k ago when the timing belt was replaced. What can I look for now???
View 2 Replies
We have a 1999 Audi A6 Avant (wagon) with about 190,000 miles. Best car we've ever owned, and want to keep her running until the wheels fall off (so to speak). We split our time between sea level and a ski town at 7000' (yes, that may be relevant).
Last spring our Trusty (sea-level) Mechanic repaired the exhaust system; both tailpipes were shot (car sounded like a tank). Rather than replace with Audi parts (was going to be a full exhaust system replacement - $000s) they spliced in some new tailpipe. Car ran quietly after that.
However, immediately thereafter (like, on my drive home from Trusty Mechanic's shop) and ever since the car will occasionally stumble (misfire) and throw a check-engine light. Typical scenario is after having been off the throttle while going downhill and then tipping into the throttle at the bottom of the hill, the car will stumble and on comes the CEL. Stumbling lasts 5-10 seconds then gradually subsides. Light stays on, though. Not 100% reproduceable under those circumstances (but doesn't really happen under other scenarios), but happens often enough to be disconcerting.
We recently decamped from sea level to spend the summer up in the mountains (great bicycling), and while the car misbehaved a couple of times on the way out of town, by the time we got to 5000 ft or so, the CEL was no longer illuminated. The car has not misfired once while at altitude despite plenty of situations that would presumably have triggered the issue, were we at sea level.
Trusty Mechanic has replaced some injectors, some coil packs, and the spark plug cables. No behavior change.
View 11 Replies
I have a 2004 Audi A6 wagon that has an intermittently flashing check engine light. I took it to the dealership to have the codes read and they told me that they got codes for Cylinder 2 and Cylinder 5 misfires. Additionally they got a code saying the Engine Coolant Temperature Sender was electronically faulty. What is this part and what does it do? Is it essential to fix it immediately?
The dealership recommended changing the spark plugs and the air filters for the cylinder misfire issue. We are also talking about replacing the timing belt since the car has 105k miles on it. I know there are several other parts that are replaced during the timing belt replacement (like the water pump, thermostat, oil seals, etc). Is it essential to replace these items if there is no immediate need to do so?
View 5 Replies
So, unfortunately, when I go to start it, it dies shortly after. So I scanned it and I'm pulling up a couple codes, actually quite a few. I'm currently at work and can't look them all up.
U102f
p0011
p052a
p0300
p0303
p0506
p0011
Most of them are misfires, but what are the chances that I've got a misfire in all four of my cylinders? Bad coil packs all go at once? I was told it could potentially be a boost leak?
View 12 Replies
I have a 2002 VW GTI, it's entirely stock and I can't get rid of this lean code. Compression is Good. Injectors are Good, Vacuum Limes are Good, Spark Plugs are Good, Coils are Good!!!!!. I only have two weeks to pass inspection in DE, I'm a college student and as most of us know, that mean $0 for car repair.
View 3 Replies
So last Thursday I started my car up in the blistering cold and it ran fine for about a minute and started to misfire so I shut it off. It hasn't ran since. When that happened the check engine light was blinking because of the misfire. I didn't have a code reader at the time to read it. now that I got a code reader the damn thing isn't throwing any codes. it spits and sputters sometimes. I've had no previous problems with the car. Thinking It might be a weak fuel pump or bad coils and in not sure how to test them.
View 1 Replies
Random multiple cylinder misfire according to auto scanner report on a 2002 Passat 1.8L? I have recently changed all belts including the timing toothed belt. I have had this very same problem prior to changing all belts on this car. Mileage is 111,000 ....
View 2 Replies
