I have a 99 alero. The temp runs right above the mid point and I get coolant over flowing out of the over flow tube. I have bought 2 caps and still the same problem. I have bleed the system thinking it was air trapped in the system after repairing a small heater hose. I thought that was the problem at first but I have repaired it and replaced the cap. But i'm still getting coolant coming out of the over flow tube.
View 4 RepliesMy friend is working on a 2004 6.0 F-250 and it has used 75% of the coolant in the overflow bottle in 5 days. Can't smell coolant either. The inside of the tailpipe is wet soot black and there are wet spots on the tube coming from the intercooler to the turbo at the turbo and the intercooler. He's thinking EGR cooler.
View 6 RepliesI was getting a check engine light with a P1112 code, so I had a mechanic replace the coolant flow control valve. There's a TSB on that and it seems to be the thing to do. But after the replacement, I'm getting overheat warning light whenever the engine needs to work hard. Also, the cabin heater only works when the gasoline engine is not running... when the engine is off, I get heat (though it's not as hot as I'd think when I have it on max heat), but when the gas engine kicks in, the cabin heat disappears.
View 8 Replies2001 Olds Alero. i'm getting a P0300 reading, Cylinder misfire, and i was told a could months ago my mass air flow sensor was out of range. are they related? how serious is a misfire? can i drive a couple hundred miles before service?
View 2 RepliesWhy am I losing coolant out of overflow on a 1999 jeep Cherokee classic for ?
View 10 RepliesI have a leak where my heater core tube goes into the intake at the rear pass side of engine. I have read that this part is pressed in. I dont want to remove the intake since i just paid $400 to have a new gasket kit put on. My question is can I bypass this tube with a hose from the water pump like in this video?
FORD 4.6 , 5.4 , 6.8, HEATER HOSE UNDER INTAKE REPLACEMENT THE EASY WAY !!! - YouTube....
If I can do a rubber hose like in the video I was to make sure that the tube just goes through the intake and that it does not supple coolant into the intake??
I have a 99 Alero that wont start. I have had 3 people look at it and they don't seem to understand what's wrong with it. I was told to replace the ignition switch and to also get a new battery , which I did. It still wont start. I go to turn my key and it does absolutely nothing. Makes no noise , nothing. When I have it in the on position all my lights begin to flicker including my headlights. They also get very dim and it makes a fast clicking noise coming from the fuse box under my hood. Someone told me that my security system needs to be reset and to put it in the on position for 10 mins , but nothing happened.
View 2 RepliesIPR CF2 Byasss High Flow Coolant Filter Ford 6.0
Made for the 6.0, the biggest problem on the 7.3 might be finding real estate for the filter assembly.
One review refers to using it on a 7.3.
I have a 2003 F250 Super Duty 5.4L V8 with no heat. It wasn't missing, running funny or blowing white smoke out of the tailpipe and there were no coolant leaks nor did it overheat. Thermostat has been replaced twice, heater core flushed twice, water pump replaced, fan clutch replaced and blend door works...Cabin airflow gets colder when turned from hot to cold. This thing is sitting in my driveway and I am about to push it over a cliff. Did I mention it only has 56,000 miles on it?
Coolant was drained to replace water pump and flush heater core (again, water ran through in both directions with no stoppage). 3 gallons of undilluted antifreeze was put into the overflow bottle to be topped off with water...the coolant went in and stopped. Engine was started to force coolant from bottle...coolant backed up into the bottle and out the top. Heater core inlet hose is hot and outlet hose not very warm if at all. Upper radiator hose is soft. Didn't check lower radiator hose as I was a bit peeved and slammed the hood closed and called it a night. I have been throwing money at this thing that I do not have and am at my wits end with it.
I have a 2001 7.3 and have found the engine oil dipstick coming out of the dipstick tube by 6 - 8 inches on three different occasions. Did not think much of it until my other 2000 7.3 did the same thing.
What causes this as afraid it will come all the way out and get into the serpentine belt.
Well I was fueling the truck today and I opened to hood to check it out and noticed that there was no pressure in the cooling system by squeezing the upper hose. I did have a spare degas bottle cap and removed the old one slowly and replaced. I have been driving over 30 minutes and it is close to 100 degrees.
I then drove on down the road, the truck is not getting hot. I stopped to look at some running boards and the truck was running and then I came home and still no pressure, the truck is still running, I removed the cap and no pressure, I then removed the small hose going to the top of the degas tank and no coolant came out. I turned the truck off and disconnected the upper hose and some coolant did come out.
Is this normal? The truck runs just fine, just has me worried. I just bought the truck and the previous owner recently replaced the water pump, T-stat, hoses, etc. All parts were bought at O'Reilly. So everything looks good.
So after a hot drive yesterday we thought to do some googling about our clutch cycling on and off so fast. Yep, the airgap was out of spec. Fixed that.
Then we added some refrigerant to the truck. The truck is "new to us" and this is our first summer with it so not sure what might've gone on previously with the AC. Didn't take long to find a rather sizable leak. :P
See that metal tube going into the "spongy" area? Yeah, that's where it seems to be coming out. That tube is the only one that's cold, the rest are ambient temp. We fix a lot on our jeeps, but the AC system is naturally a bit out of our wheel house since it's not something you normally tangle with. Is this an easy fix? Or do we need to take it in to get serviced?
I am going to install a coolant filter on my 2004 6.0 E350 van. I have read threads about bypass filters and full flow filters and I started asking myself "Why use a bypass when I can filter all of the coolant?"
Is there any reason why someone should use a bypass filter? I bought the van used knowing I would eventually have to do most if not all of the 6.0 repairs. IPR sells a complete coolant filter.
I talked with the people at FICM repair and they suggested I do my research but leaned towards the IPR cooler. Ed spent a good 30 minutes on the phone answering all my questions and never asked if I wanted to buy anything. If anything, he was trying to stop me from throwing money at the van until I isolated what needs to be repaired.
I already bought the Sinister Kit and requested a return.
I have had my 2001 Alero since it was brand new off the lot. It has been a strong running car. It has had done work on it, most recently the mechanic I'm using has replaced the intake gasket, thermostat, hoses, and coolant reservoir because of the coolant leaking. After all that still having problems with the coolant leaking (but apparently not mixing in to the oil)....I've just been putting water in and I have to stop after driving about 10 minutes to refill the reservoir.
The mechanic was going to replace the cooling fans because he said they weren't working but then he hooked up a sensor machine and there were no issues, so he ended up replacing the radiator because he thought there might be a blockage causing the water to boil back up into the reservoir, and the car overheating. The car drives great, but after about 10 minutes there is a type of sputtering. The mechanic is saying that he has replaced everything that can be replaced in the cooling system and that he thinks the head gaskets are bad.
1999 Ford Windstar started overheating. I discovered coolant leaking from a small metal tube coming out the top of the rear right (drivers side) of the engine. There are two similar small tubes. This one appears to be corroded through. I tried to pull it off, but if felt like it would break off.It's pretty far back and somewhat difficult to access. I'm wondering if this can easily be replaced and if so, how would I go about it.
View 7 Replies'90 Maxima...I've noticed coolant reservoir has been running low/dry and I also notice coolant dripping from the overflow hose. Why would it keep pushing more coolant out if there isn't an excess in the reservoir? Engine runs fine., no other issues.
View 13 Replies2014 fx4 6.2. Had a coolant leak. Brought to dealer for warranty work. Found a leak in middle lower tube area. Said they replaced radiator part # BL3Z-8005-D. It sure looks like my old radiator still under the hood complete with squished bugs. Am I missing something?
View 2 RepliesI'm trying to figure out a small leak on my mothers' Santa Fe. Recently I smelled coolant after my mother had gone for a long drive. I checked the Radiator and overflow... need maybe 1 qt of coolant.
Now I'm trying to find the cause of the missing coolant ! While it's running, I see no leak. Shut it off and it starts to drip from a small plastic tube on the firewall inside the engine bay area (on the passenger side). It drips down onto a rubber boot covering some steering stuff. Is this from the heater core?
I have read all the posts pertaining to this code, replaced my coolant flow valve, bled all the air out of the coolant system and still am getting the cel with the 1121 code.
I have tried setting multiple coolant flow valve positions, checked all wiring in harness, coolant level is full in rad and reservoir, checked temp sensor at bottom of storage tank, checked pump operation at top of tank to attempt to clear this code to no avail.
Is there a default position the valve is to be in before cold start up?
Is there anything else that can trigger this code? What am I missing?
I am having a overheating issue with my 1.8t AWP gti, it goes as fallows, start the car, engine warms up go for a drive (short 5-8 mi), park the car and temp gauge starts to rise, (turns off car)... I began to check some things with the system, I checked both rad hoses bottom is hot top is a bit hotter and fans work when ac is on; here is where it gets interesting i took off the coolant return hose on the reservoir (cold start) and nothing was flowing ...water pump?... So i turned the heat on and air full blast and all of a sudden coolant starts to flow.
It also seems like air is being spat out as well. Soon after the flow beginning my coolant in the reservoir starts to fluctuate (rising and dropping) with air bubbles and beginnings to over flow so i shut the car off. Now I know what the possible issues are its either the water pump, air in the system or bad autozone thermostat. Here is some history of the car TB was replaced at 70,000 by Previous owner, i bought the car had the belt inspected and was told it was good, about 2 months ago i had a coolant leak and had it misdiagnosed as a thermostat housing leak; it turns out it was a coolant bypass hose that was leaking so i ended up fixing it. I lost a lot of coolant but topped it off with g12+. My mechanic doesn't think its the water pump and recommended changing the thermostat for an VW one another mechanic recommended to bleed air of the system.
I do not have coolant flow. Changed Waterpump and Thermostat 2 times, hoses, new radiator and even clutch fan. I even cut out thermostat all together just to make sure that wasn't causing any flow problems. I flushed out heater core and hoses.
I'm thinking i have a block in engine not allowing flow. only thing left i can think of... So currently i have water pump removed and my question is: There is 4 open ports, 2 on each side for which the waterpump covers and pumps coolant through. Is the coolant pumped in 2 holes on one side and then comes out other 2 entry ports on other side after flowing through engine block?????
I tried to flush with waterhose, but can only get water to come out on same side of the 2 ports. NOTE: The port are ones square and other circle bore, one on each side. Flushing through square port and water comes out circle port.