Accent MC (2006-11) :: Clutch Slipping / Revs High While In Gear Without Accelerating Especially In 5th Gear
Jan 2, 2015
I've got a 07 accent with 90k miles on it. It has recently started slipping some (revs high, while in gear, without accelerating, especially in 5th gear). It also can be physically hard to move the shifter into gear sometimes (with my hand).
So, does this mean I need a new clutch? Or are there other possibilities? Should I replace/fix anything with the clutch? Sounds like the flywheel should be resurfaced? Will it shift more smoothly after the fix?
Is this something a newb could do himself? I can change the oil, rotate tires. Outside of that I haven't done much. My toolset for now is fairly limited: two jackstands, a trolley jack, torque-wrench and ratchet sets.
View 12 Replies
Advertisement
The transmission shifts into gear and when the clutch is released it starts to crawl forward. When the throttle pedal is pushed it still revs up the engine normally. But when the transmission is in gear and the throttle is pushed it revs up like it is in neutral. At first I thought this might be a transmission problem but then I figured it might be a linkage somewhere. After looking under the hood and under the car I still couldn't see anything that would cause this problem. I had this car less than a week when this happened and I had to be towed home.
View 4 Replies
2008 Hyunda Accent, 5 speed, with high mileage. She claims it slips out of 5th gear when she's driving. They're on vacation, the car is in the shop, the shop is saying that it can't find the problem...
Apparently it slips out under load (in constant motion).
It seems that it only occurs when the transmission is hot, meaning the oil has less viscosity. The dealership apparently is saying they can't find anything wrong and she isn't making it up since she said she drove from Michigan last week with her hand on the shifter the entire time to keep it in gear. Dealer is saying they aren't going to just drive it around and around until it happens.
How modern cars are built these days. I know older cars had some synchro things that would wear and allow the shifter to pop out of gear, but I read that some Hyundais have cable driven shifters....at a loss.
It happens in 4th sometimes, too, and will also pop out even when leaning on the shifter.
I did see this thread, but was wondering if there was any additional information: [URL] .....
View 3 Replies
I have a 2008 Accent (base model for the most part, no C/C), and my transmission seems to be slipping a bit. The symptoms are: slow acceleration, a delay in gear shifting, and after the 30MPH mark, it takes forever to get up to anything near 60. I just wanted to know if it's a simple solution such as topping off the transmission fluid, or if it's a bigger issue.
View 5 Replies
Tranny started acting funny recently...shifting hard into reverse at first, then last night it was like it was stuck in high gear or slipping on the way home. Limped it home and took the following codes:
P0743 TORQUE CONVERTER CIRCUIT ELECTRICAL
P0750 SHIFT SOLENOID A MALFUNCTION
P0755 SHIFT SOLENOID B MALFUNCTION
P0760 SHIFT SOLENOID C MALFUNCTION
P0765 SHIFT SOLENOID D MALFUNCTION
P0962 PRESSURE CONTROL SOLENOID A CONTROL CIRCUIT LOW
P0966 PRESSURE CONTROL SOLENOID B CONTROL CIRCUIT LOW
P0970 PRESSURE CONTROL SOLENOID C CONTROL CIRCTUT LOW
View 1 Replies
Ok, so I got my car at 60k miles, and the clutch went out almost instantly so I had the entire clutch replaced, and it was working just fine until now. It has been 25k miles since I did the full clutch replacement so it shouldn't be messing up again already. It is not going in to reverse at all, it goes in to 1st gear, but only after a lot of coaxing and grinding, and the clutch feels strange. The clutch is too soft (too easy to push down), but after a while it seems to get better.
2007 Hyundai Accent GS
Manual, hatchback
85k miles
View 8 Replies
So I have a stage 2 endurance clutch and light weight flywheel on my car. I had not really gotten on it of late until yesterday. I was getting on the highway and really got on it. When I hit third gear it felt like my clutch was slipping. I have only had it on the car for like six months and about 10,000 miles. It could be worn out all ready? And after the incident yesterday I pushed the clutch in and held it to let it cool down a bit after it did it held fine even in higher Rpms didn't feel like any kind of slipping. Pulled very strong. This morning after having all night to cool off (and I mite just still be freaked out a bit) but it seemed to feel different, like a possible slip at 3,000 Rpms but again I mite just be freaking out about nothing. What does a master cylinder or slave cylinder going out feel like?
View 1 Replies
I have a 2006 accent gls manual and when I am on the highway in 5th gear my rpms are high. if I am cruising at 110km my rpms will be almost at 3500..
View 13 Replies
So I got my stage one flash yesterday and I noticed 5th gear slipping already. I don't plan on getting a k04 upgrade, maybe stage 2 down the road. so I am looking into the drop in clutches, preferably this one [URL] .... I am just trying to find out some reviews from people who are currently running drop in clutches and the issues that they have come across.
View 8 Replies
I have a 06 plate Santa Fe 2.2 diesel and i think the cluch is on its way out, keeps slipping out of gear and the pedal itself is not aligned with the other two, mileage is about 79K i think.
View 4 Replies
So I was driving my car and notice when I was in 5th gear the rpm was at 3 and was increasing to 4 then when back to 3 or 3500 rpm. I tired it again but with a little more gas to it and got the same results. Wondering if this is signs of clutch slipping or another cause.
View 5 Replies
I have a 1994 Geo Metro that I picked up a little over a year ago. I had to swap engines and replaced the clutch at the same time. This included a turned flywheel and new pressure plate. I also replaced all seals and gaskets except for the distributor O-ring and the head gasket. This included the crank and cam seals on the front and rear of the engine as well as the seal housing gaskets/oil pump gasket. I drove it for several months and then the distributor O-ring began to leak oil profusely which is a common problem with these cars. The distributor is keyed directly into the camshaft on the rear side of the engine so it sits sideways directly above the transmission/engine interface. Some of the leaking oil went right down into the clutch area. Being that adding a cup of synthetic oil every day was still cheaper than driving one of my pickups, I just kept driving the car until the new O-ring arrived and added oil. Once the O-ring was replaced, the oil leak stopped.
I had a couple episodes of clutch slipping not long after the leak was fixed and then everything seemed fine. I figured that some oil got down there and wore off after the clutch stopped slipping. The car drove fine for about a year until I began noticing the clutch slipping under load in 4th and 5th gear. I had some suspicions of this for a week or so before it became more obvious that the clutch was most definitely slipping. I have a new clutch kit and a spare flywheel that I plan to have machined in the next few days. I have been driving it a couple weeks around town and just babying it so the clutch won't slip.
I was also told by some that I should intentionally burn the clutch some to remove any glaze build up on the clutch disc or flywheel/pressure plate surfaces. They told me to put the parking brake on or put the front bumper up against a tree and burn the clutch. I originally figured this was a bad idea but decided to try it yesterday, figuring I had little to lose. I did it just until I began to see smoke and smell it and then stopped. I let everything cool off for an hour and then took the car for a drive. The clutch was no longer slipping at all so I am wondering if this fixed the problem for now or simply delayed the issue for a short while. I am sure I took some life off the clutch by doing this but....
View 10 Replies
I have a 2012 Golf R 6 Speed manual, Just noticed that my clutch was Slipping in fifth gear when I give it gas. What clutch kit is recommended. It is the first time I have a VW and dont really know what will work better on it. Mods are Full catless downpipe and exhaust, Injen air intake and Revo stage 2 tune, ST Coilovers and NICHE Bronze wheels. Podi boost gauge and AEM wideband. I put down 285hp and 310TQ at Dyno jet 2 weeks ago I was kind of suprise expected a bit more but maybe the clutch was going bad already.
View 1 Replies
My first VW was '99 Jetta that had 150xxx miles on the original clutch before it was stolen in '11. I leased a GTI shortly after, and decided to buy it out last year. At 35,000 miles I am starting to get I guess what I would describe as a chatter when slipping the clutch into first and sometimes second. Car is stock, never abused. I tried to reproduce this for a video clip but the problem is sporadic. Never had a clutch go on me so I don't know what to expect, but from what I've seen of people losing their stock clutches after ecu flashes is the car slipping under wot in top gear. I don't have that issue. No other symptoms. No stubborn shifts or anything, clutch still feels the same and rpm's have never flared up on shifts.
View 5 Replies
Clutch is starting to slip - can't handle torque above 3k in 6th gear.
6500 miles on the car
700 miles with module
Never launched - just wind out gears occasionally
Don't have to ride clutch on hills
Not a daily driver - not stuck in traffic
I shift like a granny...
View 10 Replies
So I tried to launch my 04 accent today, but when I threw it into 2nd, all I got was engine revs. 3rd, 4th, 5th and reverse all work fine, but 1st won't work at all, and I can only get 2nd to work if I shift into 1st before hand. My question is what broke?
View 2 Replies
when cold motor reves high when in gear and car doesn't want to go very fast. after car warms up runs fine. doesn't do this in the summer. just winter.
View 1 Replies
I am searching for any kind of adjustment that might enable me to force the clutch level to the positive stop. It stands off about an 1/8" to 3/16" and I think is the reason I am not getting engagement in first gear, it slips heavily but fine in all other gears. The key way on the the lever prevents me from moving it a notch or two if I thought I could and don't know if that's even the answer . I can't figure out what is preventing it from returning fully on its own I can push it by and and a little fluid will squirt from the reservoir. Ive replaced the slave cylinder and bled it.
Is there any adjustment under the dash? This is a 2001 elantra that I just put a 2000 trans 5 speed.
My original plan was to pull the parts from the 2000 and replace in the 2001. I had lost 1st and 5th totally and found a 2000 that went right in with some minor mtr mnt mods. It shifts just fine except for this 1st gear thing. I saw a video and am having second thought about that move. I dont really want to pull the trans out again.
1st gear just keep slipping. new clutch kit installed when I swapped them out. It feels like a linkage thing somewhat but I cant find adjust ment to tryout.
View 4 Replies
Having clutch issues? I have just put 10k miles on my JSW and the clutch feels like it slipping in 1st gear when heavier load(uphill ETC) is present its even worse. We have never drove it hard pretty much cream puff.
View 9 Replies
2010 with 85k miles.
My car will randomly seem to stutter, almost like a very quick cut of power or skip, sometimes multiple times in a row. I feel like it may be the clutch slipping. It happens only at lower rpms (that I've noticed), and in any gear. When it skips, I don't see the tach jump at all and I have no cel. Are there any tests i can do? The car will move from a full stop to rolling just under the power of idle, I don't know if that means anything.
View 5 Replies
It does not like to stay in 5th gear, drops out to neutral. 2001 Accent Hatchback. 1.5l 5-speed
The other day it started slipping out of 5th gear on the expressway. Held good for the first 10 to 20 minutes. Afterwards I had to hold it in 5th for it to stay in gear. While holding I noticed it pushed on the shifter when applying throttle, and let up some when I let of the gas.
I inspected the pivots at the transmission. The forward / back bushing was not installed properly by the previous owner. I rigged it up better with a fender washer and cotterpin. It previously had just a pin and the bushing had expanded out. This removed the play from shifting I had previously noticed. It also halfway fixed the popping out of gear. It stays in gear a little longer, and when I put it back into 5th it stays there for a while most of the time.
I have not inspected the lubricant level yet. Where to check next?
View 10 Replies
