Accent MC (2006-11) :: Suddenly Started Running Real Jerky, Rough / Misfiring
Jun 4, 2012
Our Accent has just about 86k on it now, back in November it suddenly started running real jerky/rough, misfiring kinda thing. So I was able to drive it to my local repair shop and they found a bad coil pack on #3, so they replaced that and put in new plugs while they were doing it.
Just Saturday we were shopping about 20 miles from home and cranked it up to go home and started doing it again, pretty much identical symptoms, runs out normal at certain RPMs so I knew it was probably same thing...I was able to get it home and then took it in this morning and sure enough now #1 is shot. So they are replacing that. They want about 30$ more per coil then I can order them for myself online so I didn't want to scarf up the money for the other 2 that are still original.
View 29 Replies
Advertisement
So Friday before last my ex laid down on me while i was headed to work. So I parked it in a walmart parking lot and caught a ride to work with a friend then had it towed home that evening. Problem i was having is it started running really bad, miss firing, smoking, and sounding real rough, but I wasn't getting any trouble codes. So after both uvch's, icp, ipr, icp pigtail, checking fuel for water contamination and pulling my hair out, i decided to check the oil and found it to be 4 quarts low. Talk about feel like a knuckle head.... While it was down it did receive a new water pump, a diesel site 203* thermostat, new billet thermostat housing, Gooch's Radiator Flush Procedure, and some fresh rotella etc.
View 5 Replies
So after taking my car to the stealership to get defective door seals fixed, I start driving home and I realize the front tire is flat. After changing to the awesome 17" spare, I decide to get gas. After filling the car up, it started for a few seconds running real rough and then shut off. I tried restarting it multiple times for about 10 minutes and the car kept turning over, but no start. I finally just shut it completely off for five minutes and it restarted, but is running roughly with the CEL light on and another green light, EPL, or something like that. I was able to drive home, but the check engine light is on still and runs like crap.....Back to the dealership in the morning. What this could be? I noticed lately sometimes when I push the gas hard it kinds of bogs down for a sec before accelerating. I had them check this and they said nothing looked wrong when they tested it. Fuel pump maybe?
View 13 Replies
I have a 2008 Kia Rio, 4 Cyl 1.6L, and recently the check engine light came on and the car started running real rough after getting the timing belt replaced at firestone. I took it back to Firestone and they said that 2 of the cylinders where misfiring and i need to replace the ignition coils and the corresponding spark plugs, but that i also want to get a catalytic converter cleaning or flush or something like that because of the unburnt gas that was running into the converter. Is this true? They want to charge me another 100.00 for the cleaning on top of the 300.00 to replace the 2 ignition coils and spark plugs, should i get this done or can i clean it out myself?
View 6 Replies
I have been puzzled to why my truck isn't running right. We were driving down the highway one day and*then all of the sudden it starts running really rough. I changed MAF sensor, plugs and plug wires, oil change, fuel filter and air filter. Still doing the same thing. What this could be? 2003 ford sport trac..
View 11 Replies
I have a 2011 Hyundai Accent 1.6L. A few weeks after I bought it w 38,000 miles, it started misfiring so I replaced the spark plugs. It ran great for about another 6 months and started misfiring again. I took it to Hyundai to have it fixed and of course it wouldn't do it for them. I told them what it was doing and they said that there was no code so it was probably my spark plugs. I replaced my plugs with the OE plugs and got the same trouble about 4 months later. Now it has 60,000 miles and my warranty is done. I put in new plugs yesterday and it only ran well until it warmed up and it did the same thing. I ordered new, better than OE Delphi coils yesterday and I'll get them today. I feel like there's a bigger problem with the system that's causing the problem with the coils.
View 7 Replies
I have a 2001 F150 4.6L auto. This truck suddenly started running rough. Cleared all codes and re-scanned after starting truck. The codes are as follows; P0135, P0155, P0443, P0740, P0743, P0758, P1451, P1460, P1747, and P1760.
My question is; is it normal to have this many DTCs come up at once? Could my PCM be faulty causing this problem? Can you swap a pcm from the same year truck with the same options without reprogramming?
View 2 Replies
The Basics: I have a 2011 GTI with 44k on it. First GTI, I have had it for a few months...
I was leaving for work yesterday and the CEL came on and then it started to run real rough. I pulled the codes with a auto zone scanner and I got these:
P2015 - sensor 1 bank CKT range/perf
P2279- air intake leak
P0300 - multiple misfires
P0301-P0304 cylinder 1-4 misfire
I did a bit of research on here and it sounded like a PCV valve. So I picked one up and I installed it. Problem did not go away. I then read that maybe pulling the battery may clear the codes... It did not. Now I have a lot more lights on.
View 13 Replies
Owning a Hyundai. I have a problem and it seems to be pretty common but haven't gotten anywhere with it yet. Last week my 2004 accent 1.6 manual transmission started running rough. It was idling higher than normal and while driving would not go past a certain rpm (about 2500 if I had to guess,no tach). On the way home from work it was running this way and then started badly misfiring and shut off, when attempted to restart it would not. I pulled the codes with a scanner and got p2400, p0562, and p0121. I charged the battery and replaced the throttle position sensor, still won't start. I can hear the fuel pump kicking on when I turn on the ignition. Also found the ecu 1 fuse blown, replaced it and continued to attempt to start with no luck, fuse was blown again. Like I said I haven't owned the car long and I don't know much about it. I am not sure where to go from here and I don't know how all these symptoms are tied together.
View 42 Replies
I was driving my '98 Jeep Grand Cherokee Laredo (6cyl 4.0l 4 wheel drive) on the freeway when it, very suddenly, started shuddering badly. The check engine light came on and then started blinking. I pulled right over and shut it off. I stared it back up and the engine is misfiring badly. I had a code reader with me and it's showing three codes. A random misfire, a cyl #5 misfire, and a Cyl#6 misfire. It will sit and idle (very roughly obviously).
There was no drop in RPMs, oil pressure, voltage or anything when it happened.
I got it home and replaced the distributor cap/rotor, all six spark plugs, and the plug wires but there is no improvement. I cleared the Codes and re-read them and got the same errors again.
View 4 Replies
I have a 2009 Hyundai Accent with 52000Km (32932miles) The car was parked since 2011 and now when I started it, it started really rough and would not accelerate (it would die if i pressed the acceleration pedal) but now after multiple attempts the car sounds like it wants to start but it doesn't unless I press the acceleration pedal when starting the car then the car revs to 2000rpm and dies within 1-2seconds,I also hear a odd sound from the intake its like a loud rumble. So far I have tried
- changing the spark plugs
- changing the coils
- checked spark
- cleaned intake manifold
- cleaned throttle body
- replaced PCV valve (because originally there was alot of oil in the intake)
- checked if fuel pump is pumping gas
I also checked the engine codes and there is a code for crankshaft position sensor abnormal -P0336 I unplugged the crankshaft sensor and the car wont start at all further more I also checked if it was sending the correct rpms with my obd tool and it seems like it is ...
View 9 Replies
I have a 2008 Accent 1.6L automatic that is running very rough when it accelerates. First of all there was some engine check light, I got the codes and it was a Cylinder misfire. Then I checked the following:
1.- Spark plugs (replaced them same NGK but I didn't gaped them, same result)
2.- Fuel injectors (removed them, cleaned them and installed in different order, same result)
3.- IGN coils (measure resistance, swap them in different places, same result)
4.- Checked most of the sensors including TPS, Crankshaft PS, MAF, Camshaft PS and nothing.
5.- I checked for any type of vacuum leak and I couldn't find one
After all that troubleshooting I cleaned the codes, started the car again and I have the same problem with no check engine lights on except that sometimes I would get a "running rich" code.
I also noticed that the air intake is LOUD like a performance air intake, is that something normal on the accent? (I checked the air filter and its not clogged FYI). I could only think of:
Gap spark plugs to .035
check timing belt
check fuel filter (I don't think so)
View 11 Replies
I have a Ford F150 XLT. I have 67000 miles on it and the other night it just started running rough out of no where near idle. Once you got over 20mph the rough running would go away. I took it to get an engine change and engine flushed but it came back. It doesnt always run rough near idle or below 20mph. The Ford dealer says my engine has only 22 psi oil pressure near hot idle and cant engage the VCT phazers and they want to replace the whole engine.
View 1 Replies
I have a 2008 Accent. Yesterday the check engine light started to blink and the car started stuttering and the idle was rough. I've changed the air filter, which worked. But, it was recommended that I change the fuel filter. But, when I went to the parts store, they say that this model has a fuel strainer instead. What is that and where is it on my car? Is it easy to replace?
View 4 Replies
The check engine light came on after cleaning the engine and the engine runs rough. Where to look. 2007 Hyundai Accord.
View 5 Replies
I have a 1999 F250 SD V10 4x4. I recently had a transmission installed and the truck is running erratic. I have an engine miss (sometimes when idling, more so when in drive and foot on the brake). I say sometimes because there are times it will not miss and the engine runs smooth. The transmission shifts a little strange and sometimes hard.
I am getting a code reading that says my TPS is faulty, but I installed a new one a few months back.
The engine is running rough (jerky on acceleration) especially when driving. I was wondering if I should take it to a shop and have them flash the computer to reset it?
I also remove the AC compressor a while back (bad clutch). I installed an aftermarket pulley.
View 2 Replies
Check engine light had come on, the car was running rough at idle and it would crank hard. So I threw my code scanner on it only to find out it wouldn't link. Drove it to O'Riley's and had them pull the codes. It ran rough and had next to no power on the way there. O'Riley's pulled the codes and we got a P0300 (random multiple misfire), P0301 (cylinder 1 misfire), P0302 (cylinder 2 misfire), and a P0496 (EVAP emissions system high purge flow). So once I got it back to the house, she told me that she had the codes pulled once before and that they told her it could be her gas cap so she replaced it. She also stated that she had replaced the plugs about 3 months ago.
So with new gas cap and new plugs, and these codes, I did a bit of research and come to the conclusion that it'd replace the purge solenoid. The solenoid was making a pretty loud ticking noise and when I pulled it off, it rattled so I figured that was the fix. Pulled her plugs and you can clearly see that cylinder 1 was running VERY lean and cylinder 2 was a little richer but still too lean. Plugged the plugs back into coils and laid them on exhausted. Turned the car over and we had spark. Lead me to think the misfire had something to do with the P0496 EVAP code. Put everything back together and erased the codes. Gave the car back to her and told her to let me know if the light came back on. That was Wednesday last week. Sunday she told me the light came back on and the only code that came up was the P0496 again. When I gave it back to heron Wednesday, it would still crank hard but would start.
Battery is new and checked good, alternator is pulling about 14v and checked good and the starter checked good. My dilemma is the code and the hard crank. She told me that it only cranked hard for her once so I am assuming that has gone away but we're still left with the P0496. I am not 100% sure as to how this system operates but I understand it for the most part. She told me that she had just put gas in it before the light came on. Not sure how much time had elapsed after filling it and the light coming on but I do know she put gas in it. If it's a high purge flow, that makes me think there may be a leak in the system but I'm not sure where to go from here without throwing a bunch of parts and money at it.
View 14 Replies
I have a 2006 E350 van, just recently had passenger side injectors replaced along with dummy plugs and stand pipes. I was at the car was spraying it off and noticed it started running rough, just figured maybe some water made its way into the engine bay and something got wet as it was running great. Well its stayed that way and i am getting codes p0264 and p0276. Digging around on the net seems like its ficm or wiring, ficm is 48 volts and 13.5 volts, connectors are on tight and i dont see any wire chaffing kinda stumped. hoping its not 2 bad injectors at once.
View 2 Replies
So I have a 2006 Hyundai accent with 75000KM on it. I notice when it shifts from 1st to 2nd gear sometimes it will jerk. It feels almost as if it goes to neutral and then sifts, causing the whole car to jerk. It use to only do it when the car was cold (first 15 min of the day) but now it seems to be doing it all the time and getting worse. I have had the transmission fluid replaced, but it doesn't seem to work.
View 30 Replies
My 1999 lexus rx300 first threw a P1135 following a P0125, I tested the sensor and it was open at the heater circuit then then I was waiting the new part in the mail and during that time it kept running rough and then it threw a P0300, P0301, P0305, P0303. I was thinking that the PCM cannot monitor A/F ratio without the sensor so maybe the injector base pulse width was good enough. The misfire is are on bank 1, same as the bank 1 A/F sensor.
View 3 Replies
I bought my 2012 Camry, with 12,000 miles from the Dealership in December of 2013. The car was sold as CPO, car was purchased on Dec 30... just 6 weeks ago and I have had numerous issues with the car Misfiring. When I arrived at the dealer, the CHECK ENGINE and TIRE TRACTION lights are one and the car is running very rough as acknowledged by the service techs. For the 2nd time now, I am told they are not able to recreate the problem, so they are not able to fix it.
This is my 4th Toyota and I have NEVER had this many problems with a Toyota. Did I get a lemon? Service tech says he can't fix it unless he knows exactly what's wrong. I am asking him to check the spark plugs, check the ignition coil...and his response is that they can't just go on a wild goose chase, they need to know what they are looking for. Does this sound reasonable?
View 17 Replies
