Accent MC (2006-11) :: Rough Idle At Start Up With Flashing Check Engine Light (while Low On Fuel)
Apr 17, 2012
I have been experiencing some issues with my '06 rio5 (same engine as your hyundais). this forum is way more active than the kia forums, so figured id give it a shot here.
I am experiencing a rough idle at start up while the car is low on fuel (<1/4 tank). it idles rough for a few seconds, the check engine light flashes a bit, and then it runs fine.
The car is an '06 rio5 with approx 19k miles on it, five speed manual. Also, sometimes after refueling and it will just shut off while waiting at an intersection. Not sure whether these two issues are related, but thought i would mention it just in case they were.
View 14 Replies
Advertisement
I just bought this car from the original owner. She didn't take that great of care of the car. First oil change was done at 8,000 miles for example. Basically if it was broken she would fix it, but didn't do much preventative maintenance.
I just replaced all 4 spark plugs and coils since one was misfiring and didn't want to have to go back in and replace one in another few months. Replaced the AC belt a few days ago since it was cracked and worn. All other belts are fine. I drove the car around for a few hours the next day and it ran great.
Today, the check engine light flashes and then stays on. The car is idling rough at stop lights and acceleration is poor. Previously, the light came on and it was the EVAP system. Not sure which component and I was told it isn't supposed to affect the way the car drives.
View 14 Replies
Yesterday my car had a rough start (lasted all of 5 seconds) and it threw the check engine light on. Now other symptoms. It was a rough start, almost like a misfire then it idle fined, and drove my 60 mi commute home without issue. I had fine acceleration, gas mileage idle etc.
I got home and turned it off for 10 min and it then started normally and ran fine again. I'm thinking it was just a random miss that threw on the light, but I'll take it to Advance to get the code later today.
I replaced the plugs about a year ago with cheap-o plugs so it may be time for a replacement again. I thought maybe an o2 sensor but there wasn't a drop in mpg, at least anything noticeable.
And its been a few days since I've gotten gas so I'm doubting just a gas cap issue... The CEL did NOT flash, only solid the whole time.
View 8 Replies
As the title says, my CEL goes on and flashes too.
I've read up a bit on why the CEL comes on/flash and it says it has something to do with the exhaust system and if continue operating will damage the catalyst converter (which I don't understand since I'm a car dummy.
In addition, the engine vibrates like crazy. I can feel the engine vibrating when I'm inside the car as well.
I already got the car tolled to the dealership and they kinda just told me it might be misfirings and then they said they couldn't locate the problem. So my car basically has to stay there until they open again on Monday and hopefully they will figure out the problem/fix it under the warranty and call me back.
The problem arise late Friday night and I just did a 30K maintenance on Thursday. (but the car already has 43,000 miles on it).
View 35 Replies
My 3.0 with 216k miles has developed a rough idle and it progressively got better with new parts and cleanings. On startup it revs up to 2k then back down to 600. If I let it idle for about 8 or so minutes my Check Engine Light starts flashing. If I drive about for a little bit it stops and is just fine.
While the light is flashing I get codes P1000, P0305, P0306, and P0316. Which are OBDII Monitor Testing Not Complete, Misfire detected in Cyl 5, Misfire detected in Cyl 6 and Engine Misfire Detected on Startup (First 1000 Revolutions) respectively. Any other time the truck runs like a dream. Gets 20 city and 29.5 highway.
I cleaned my Mass Air Flow, replaced my Idle Air Control, SeaFoamed throttle body and vacuum lines, brand new coil pack, new wires, new plugs, new fuel filter, I've only ever run 91 octane, Chevron with Techron goes in at every oil change and B12 every other and I just ran 3 bottles of Lucas fuel injector cleaner.
View 12 Replies
It happened randomly on the way home from work, the car chugged along with the check engine light flashing at me and then staying on. I was able to limp it home and got a ride to the nearest auto parts store to get some new plugs. I went with the NGK brand. Well, $60 later (including tools on the spot) and it's still running rough.
I know best case it to try and limp it to the autoparts store to let them try and pull the codes. I noticed an old thread where updates were made to the software to correct a running issue. I will note this same chugging randomly happened at 50,000 miles. I shut the car off, let it sit for a moment, restarted and it ran just fine. The engine vibrates noticeably just like it did at 50,000.
2009 Accent running rough 73,000 miles....
View 6 Replies
I just replaced fuel pump and tps on my 1989 Dodge Dakota 4 cyl truck. Now it idles rough and the check engine light came on. I have removed battery cable to reset computer but did no good. What could be the problem now? I have since replaced the plug wires and distrib cap and it is flashing 3 5 5 twice now?
View 10 Replies
I started my Accent this a.m. The Check Engine Light is on and it runs really rough. I left it here at my apartment - it's that bad. It's got 27k miles.
The only other thing to note is that it's been very cold (for Northern California anyway) - around 45 degrees F right now.
First-time poster, haven't had any problems with the accent except for a sun visor that was replaced under warranty last week. All scheduled services done at the Hyundai dealer.
View 20 Replies
The check engine light came on after cleaning the engine and the engine runs rough. Where to look. 2007 Hyundai Accord.
View 5 Replies
I did not get the specific cel code but its what the guy told me at autozone.
Long story short. Washed engine, let sit for about 30 mins. Car started with flashing CEL and was "puttering" and very rough idle. Drove home took intake off and replace with stock, took spark plugs out and they were not wet. Then let it sit for about 15 mins. Started just fine. No CEL at all.
The accent saved the CEL and the guy told me that Cylinder 1 had a misfire.
My question is, should I do anything now even though the car seems to be running ok?
View 26 Replies
I recently purchased an 06 f150 fx4 5.4L with 60K miles. Just recently my check engine light came on and I've noticed a slight rough idle in park. I took it to autozone and the code read P0422 evap emission leak. Bought a new fuel cap but didn't work... EGR valve?
View 2 Replies
The check engine light came on in my 2000 Jetta and the engine power suddenly decreased noticeably. Got worse quickly and was idling rough, like it was about to stall out (but didn't). Took it to dealership, they said spark plugs were the problem and replaced. All seemed normal driving home, but after 10 minutes, same problem: check engine flashing, weak engine (trouble on hills), and a rough idle.
Two questions: what could it be?
and is it safe to drive back to dealership (~10 miles) or might that cause further damage?
View 1 Replies
Rough start like some thing missing, check engine light came on, shut off car checked my oil, ok, restart runs smooth but check engine light stays on, went to dealer 8 mile drive, car ran fine ????
View 12 Replies
I go in this week to recheck my nagging check engine light. Flashes after a warm start, then stays on. Been there once already for it, it has come on too after a cold start... Last time they said it was a very vague miss fire code.... It did shake a bit... On the plus I get to drive a nice new Elantra again.... On the down, I never want my car back after driving it ...
View 2 Replies
If you get a f!ashing cel ,the next time you start it should it flash right away or can it go back to solid on cell? 02 Accent 1.6 130 k. What can be done to check the flex pipe for a leak? Can you spray water or what? The outside looks good. Also looks hard to check around intake manifold for leaks.
View 11 Replies
My check engine light just appeared like an hour ago. In idle, it sounds like a big flicking V8 Supercharged (I actually feel the car vibrating) and I need to give it a LOT of gas to start in 1st. When I turn the key, it takes a while to start. It is flicking weird. I am dropping my car first thing in the morning, but somebody got that so far?! And the last thing I did before getting the light is reversing in a parking lot and parking my car. I have my car since december.
View 6 Replies
Ok on the way the my 1997 f150 4.6 L 180,000 check engine light started flashing and running rough and then the light went off, Also we took the Aftermarket Dynomax muffler off of it earlier today if that makes any difference, it still has the Cat Converter, New Plugs and Napa Wires.....
View 12 Replies
I have a 2010 2-door accent, automatic. Today after driving about 45 minutes (engine warm), I stopped the car. When I tried to start again, it wouldn't turn over. Turned over on the third try; tachometer read at 0. Managed to drive home (35 miles), and the car did shift from gear to gear, but engine sounds tinny on idle. Turned off car at home and turned back on, still rough start and tinny idle but tachometer appears to be working again. No check engine light. At a loss; I've heard that there are a couple of crankshaft sensors that could do this, but I really don't know. Car is regularly serviced and has new belts (belts look fine), new strut plates, new tranny fluid, all about 6 weeks ago.
View 2 Replies
Got an 07 Screw with only 50,000 miles. Yesterday, wife drove it home from work and said it would only do 45mph and didn't sound good. No warning lights were on, she said. I test drove it in the evening and it ran totally fine. Today, she drives it to work and said it ran real rough and "Check Engine" light was on. I picked it up from her work and it idles very rough and slow, and once you hit about 2000 rpm, it runs decent, maybe even normal. Below that, it stumbles and engine doesn't sound right. "Check Engine" light is either ON steady, or flashing. I don't have a code reader, so its likely going to the Ford Dealer Monday. Is there any way to read the code without a reader?
View 11 Replies
2005 F-150 4.6L 2WD, 268,000 miles....
Recently I got a flashing 'Check Engine' light and a rough running engine (along with a tapping noise) when I was passing someone (and pulling a trailer). I retrieved codes 300, 304, & 305. I can't swear to it, but I think the tapping noise started at the same time as the coil problem.
I replaced coils #4 & #5 (later that same day) and the engine smoothed back out but the tapping noise is still hanging around. The noise speeds up at higher RPM's and doesn't go away if I shift into neutral. Oil level and pressure are fine and I only use Motorcraft 5W-20 and Motorcraft filters (and change the oil every 5K miles).
Not sure if this is relevant: I think I have bad valve guide seals (blue smoke after long idles) but no other problems that I am aware of. It sort of sounds like a lifter, but is there a good way to pin it down? Is it possible that this tapping is related to the bad coils?
View 5 Replies
My 99 Explorer XLT V6 SOHC has been misfiring lately. In idle the RPM needle fluctuates a bit and the vehicle vibrates and shakes. At night when the lights are on I notice them dim a bit as the engine struggles in idle. It doesnt stall very often at all. Accelerating I notice way less power and the engine studders. Thats when the engine light comes on flashing. Then remains on solid afterwards.
I brought it to a mechanic friend who read the code and it was cylinder two misfire as well as O2 censor. I replaced the plugs and leads and censor. Noticed the plug in cylinder two had little to no gapping. Thought I had fixed the problem. Vehicle ran perfect. Three or four days later driving on the hwy same problem came back. Thinking it must be the coil pack I got one for a good price and replaced it.
Again, the truck ran great for four days and now the problem has returned. Same thing, shaking studdering and flashing engine light. I have verified the locations of the wires and plugs a few times so i believe they are all properly installed.
View 7 Replies
