My right rear brake is making a grinding noise when the brakes are applied. I took the drum off a couple weeks ago and the shoes are just a bit worn. Just getting into the numbers printed on the side of the shoe material.
I could not see any thing that would be making the metal on metal sound. Are there any wear indicators on the OEM shoes?
I have a 2012 dodge caravan bought new. After about 6000 miles the left rear brake began making a grinding noise, only when applied, every time the car sat more than a few hours, that goes away after about 2-3 miles. It began in winter and continues into the warm and dry days of spring now with 9000 miles total. Had it to dealer twice and inspection found no malfunction so they say its from rust build up because it goes away all the time and is nothing to worry about. It does not occur with the other wheels. My niece has the same van, in same geographic area and does not have this problem. Does this selective rust build up explanation make sense? Previously burned with bad brakes on a caravan, so am skeptical.
View 7 RepliesIs it just me or is this an ABS thing? during a snow storm i was going about 25mph and had applied the breaks and started making a grinding noise... if it is the abs how are you suppose to work with the response time for a quicker stop.
View 2 RepliesMy brake pedal is making a creaking noise when depressed and can also be heard when letting off the pedal. The noise is not coming from the brakes themselves (front/back are like new) but the pedal area or somewhere behind it. This noise doesn't start until I've driven the car for a little while. The brakes work fine for the most part but sometimes feel a bit spongy if making a sudden or hard stop. The fluid levels are fine.
I'm taking it in on Friday and hoping that the brakes just need to be bled a little or maybe the pedal just needs lube, but I'm worried it might be the booster or master cylinder---if it is one of these?
I noticed yesterday a sound, like a grinding sound, *sometimes* as I apply the brakes to stop. I'm at 68k. The noise only happens when the brakes are applied so I suspect there is an issue with my brakes again.
Some BACKGROUND info: At around 60k (or 8 months ago roughly), the front pads were replaced after the brakes were squealing and a pulsating brake pedal when stopping. The pads were replaced by a dealer. In addition, both front/rear rotors were turned at the same time. Rear pads had 40% at the time and were not replaced.
Some weeks later the pulsation came back and I went back again and they machined them again. For this current issue I was thinking about taking the car to someplace local (not a dealer) and getting a free brake evaluation of what is going on.
I'm also concerned that all this machining the dealer did to eliminate the pulsation may have decreased the life of the rotors and perhaps they need replacement now.
I have an 2002 Hyundai Auto.
My car has the clicking noise under the following situations:
1) rolling in neutral with/without brake applied
2) rolling/decelerating without gas pedal pressed (I guess the same as rolling in neutral) with/without brake applied
The noise is the most noticeable when going at around 20 to 30mph, and would be gone under very low speed <5-10 mph. The weird thing is when I press the gas pedal and the car is accelerating, the noise is gone too.
My mechanics said it is because the wheel cylinder which is noisy. But I don't quite understand why the noise is gone when the car is accelerating.
My car came back from the shop yesterday with new brakes and pads and seems to be making some odd noises, both at low speeds and while breaking. I called the shop this morning and they said that this sound was normal for awhile but to come back in a week if it persists. Is this sound advice, or should I be driving my car right back to the shop?
2005 Hyundai Tucson 122,000 miles
I have 23, 400 miles on my Kia Sportage 2009 and just found out I need to replace both of my rear brakes.They were making grinding noise. Is this a defect? Seems like low mileage to have to replace them?Also my front brakes are down to 50%. Is this a known KIA issue?
View 4 RepliesI have a 1997 F150 (truck in signature). In December my passenger side parking brake cable broke so I replaced both rear cables (front cable appears in good condition).
This past Friday the passenger side brake started making a grinding noise so I pulled the drum to find the self adjuster cable broken and the ratchet jammed between the shoe and the drum. I pulled everything apart and put new shoes (the pin the ratchet pivots on was broken off the rear shoe)and all new adjusting hardware (adjuster screw, ratchet, cable, and cable guide). The rest of the hardware looks in good condition (still paint on the springs and retainers). I got everything put together and took it for a test drive, it had a nice firm brake pedal (it's been a while since this truck has had a firm pedal) and great stopping power.
Took it to work today, and on the way back I stopped to pickup a package from the UPS store. I set the parking brake and put the truck in 1st like I always do. When I got back out to the truck to drive home, I released the parking brake but there was still obvious drag as I drove home (no good place to stop during rush hour), got out of the truck and it reeks of burning brakes. I pulled the driver side drum off (after it cooled), which was rather difficult, and everything looks to be in order except the rear shoe was not touching the post at the top of the backing plate. I checked and the adjuster was still all the way in, so that isn't the issue.
I pulled the parking brake cable out to slack the drum side of it (with the pedal released there is some spring tension from the pedal mechanism) and clamped it with vice grips so the cable was slacked and the shoes were then touching the post, and the drum could be installed and turned relatively easily, I then removed the vice grips and let the spring pull the tension out of the cable and the brake held firmly (requiring considerable effort to turn the drum). Is there anyway to adjust the spring tension on the parking brake cable when the parking brake is released?
Additional notes: when setting the parking brake, the pedal will only go down an inch or 2 before the brakes are locked up tight and the pedal won't move, it used to go down several inches before. also I noticed that the feral on the end of the drivers side cable (that locks into the lever attached to the rear shoe) is deformed, like the cable has too much tension on it. The cables are the correct ones for my wheel base according to Autozone but I'm starting to wonder if they are too short. Spring tension on the parking brake cable (when the brake is not set) causes the parking brake to drag. How do I get the parking brake to stop dragging? ("star" adjusters are new and adjusted all the way in).
I have a 2012 Hyundai ACCENT 4 door 45K miles. There is grinding noise that I hear when I do a slow brake. At first This grinding noise use to only happen in the morning the first couple of years, it would go away within minutes or less. Now, the grinding noise is almost during every slow brake at a red light etc. It's a grinding horrible noise that seems to be getting worse.
View 2 RepliesMy read brakes have been grinding. I bought new pads to replace them. After pulling the drums I noticed that they were hardly worn. 50,000 miles on the car. They was a bunch of brakes dust in them. Cleaned the dust out and put the drums back on. It was quiet for about 3 weeks, now the grinding is back.
View 3 RepliesMy daughter has bought a 2003 4 door accent and on the way to work she lost most of the brakes. I could not see any fluid leaking and the level was ok. I did try pushing on the brake pedal with my hand and it was making a noise like a clicking? I was thinking it was just the brake light switch but not sure. The place she bought it from put new brakes on it when the driver side was getting really hot. I am thinking maybe air in the system? It sounded like a caliper was sticking when I test drove it but only a couple of times. You would have some brakes but you had to pump the peddle.It is in a parking lot right now but I can work on it unless it is some sort of different? I am going to try to bleed it in a little bit but was thinking I should ask around. I read that the piston could be sticking but can you just rebuild the master cylinder to fix it if that is what it is? I could pull the pedal back a little bit. I only looked at for 4 or 5 minutes kinda dark and no tools with me.
View 10 RepliesI have a 2007 Elantra with 138,000 miles. I never had any slipping or jerking or reverse issues in the past. I got into the car put it in reverse just fine then put it in drive and nothing happened, I put it in park and the car kept rolling like in neutral and started making a loud grinding noise. When I put the transmission in any other gear the noise stops but will not move and acts as if in neutral.
View 2 RepliesI have a 2007 Toyota Camry 4 cylinder and the ABS light comes on intermittently. Not only does the light come on, but sometimes when I apply the brakes, the brake pedal makes a grinding, vibrating sound that I can hear and feel under my foot, and feels as if the brake pedal is going to go all the way to the floorboard. If I quickly pump the brake, it stops that sound and the brake works fine.
I have taken the car to O'Rileys and Firestone and they put it on the analyzer. Two codes come up which indicate that the right front ABS was bad and/or an open circuit. I replaced the ABS sensor, but the problem described above persists. I took it back to Firestone and the same codes displayed. Firestone said it was an open circuit and that I should take it to the Toyota Dealer. I called the Dealer and they want $135 to analyze the car. They won't tell me what they will do in the analysis. I also took it to Just Brakes and they kept it for 3 days and could not or did not do much other than suggest I take it to the Dealership. I have read that the Dealership will probably say the ABS computer needs to be replaced ($1,000). I have also read that the 2007 Camry Hybrid ABS brake system has been recalled, although my Camry is NOT the hybrid.
There has had two fender benders on the left front side and the right front passenger tire hit a curb which bent the tire, but the tire has been balanced (not sure if the wheels were damaged in these minor accidents or if the wheels could be causing this?) Other thing that occurred right before the ABS light started coming on, and the brake issue, is that the air conditioner went toes up, and there were small metal fragments within the air condition housing unit. I replaced the whole A/C unit. I haven't been able to assess if one would have anything to do with the other, but it is interesting that the ABS and brake issue all started within a few days of the A/C unit being replaced.
I own a 2005 Hyundai Accent 1.3 SOHC and a while ago the front right wheel started to make a grinding noise, problem was related to the brake system..
So far I've tried replacing the rotor (disc), repaired the caliper (using a rebuild kit), replaced hoses (both), and event the master cylinder.... and the problem persists, it actually came to the point that after driving a while the front wheels will get stuck.
I've followed all the directions from the service manual and it still got the problem...
Occasionally the car will make load grinding noise that sounds like a garbage disposal:
[URL] ....
[URL] ....
When this happens the gas pedal is also vibrating. It will go away when the car is stopped and may not return for a few days.
It's 2008 accent SE with a performance chip.
I have a 6-cyl, 2000 Camry that is making a scraping noise from the right rear brake. After driving it for a while I put my hand near the rotor and it was hot. The other side wasn't. I changed the pads and rotors yesterday and it's still making the noise. I'm guessing that there's something wrong with the caliper. Do I need to buy a new one? Can I rebuild the current one?
View 6 RepliesWe have a 2010 Hyundai Accent, with low miles (10,000), and the A/C Compressor is making a "growling" noise. The only way to explain the noise is when you hear a human try to immiate the sound of a dog growling. That's exactly what it sounds like.
First thing in the morning it doesn't make the noise to much, but as you drive for a bit you will start to hear it. Sometimes it's really loud, sometimes quieter. When you shut the A/C off, it will continue for a few seconds then stop.
The service department told me it was the compressor and it is, "pretty normal on the cars." How is that normal though? It sounds awful.
I have a 2009 Accent 4-door sedan.
I was told during an oil change in the spring that I would need a new battery soonish. I haven't bought one yet.
Last week I tried to start my car and it made a machine gun noise and wouldn't start. A friend jumped it and it started fine. I took it to Canadian Tire and a mechanic tested the battery and said it was over charged, 508 I think, should be 500.
Then today it won't start and is making the machine gun noise again. Now the horn and lights are dimming too when I lock it.
What is going on? I checked the posts; they are clean and tight.
My girlfriends 2013 Hyundai Accent is having some problems. Yesterday, the Check Engine Light came on, but went out on its own maybe 15 minutes later. She did not feel that the car was running any differently.
This morning, after the car being parked through the night with the parking brake applied (she usually does not apply the parking brake), she observed that it still felt like the brake was applied when she tried reversing out. I told her to pull and release the brake a few times, but she said it was no luck.
What this might be?
I have a 2006 Subaru Forester with 115K miles. It's been well-maintained and well-loved.
For the past few months, the brakes have been inconsistently making a dragging/grinding noise when coming to a stop at low speeds (<5mph). It sounds to be coming from the front half of the car - I can feel it vibrating a little near the driver side. We've taken the car in to be looked at three times - each time, the mechanics think they've heard the noise and report there is absolutely nothing wrong with the brake pads or rotors. Twice they reported a shim was out of alignment. After the last shim adjustment, the noise got a little better - instead of grinding, it's more of a dragging sound now. Because the noise is inconsistent, I haven't been able to crack the formula of the conditions that produce it, other than that it only happens as I'm coming to a stop at very low speeds.
Is there something besides the brakes we should be having inspected? Does this sound safe to drive?