Accent MC (2006-11) :: Power Steering Pulley Locking Up And Start To Slip
Aug 13, 2013
I have a 2007 Accent GLS with 70,000 km on it. At times, my power steering pulley will lock up and start to slip. All belts have recently been replaced. After about 2000 km after replacement, is when the problem started. The problem is intermittent and the pump itself turns freely after the belt is removed. When it locks up a loud squealing sound can be heard. This happens only when tight turns are made (usually it's to the left). Could it be related to the pressure switch relief or relief valve?
View 11 Replies
Advertisement
So I purchased a 2009 Accent hatchback about 11 months ago and so far its been great. However, recently (as in the past 2 weeks or so) I have begun noticing a strange cyclic noise developing from the engine compartment accompanied with some minor vibrations. Over time it has grown more prominent. I would rather deal with this before it becomes worse (and more costly) if its a serious issue.
Some info: I recently took a trip to North Carolina (from Florida). I also recently replaced the spark plugs before I left, so they are relatively new. The car has about 37k miles. After popping the hood and taking a look, it seems as though the noise is coming from the power steering pump/pulley area. The noise seems to match the rotations. Either way, here's a video of the noise (pardon the moving in the video, I was mainly recording for sound): [URL] ....
It may sound like normal engine operation, but it did not make that cyclic sound for the first 10 months, so it worries me. Perhaps I'm just paranoid.
View 4 Replies
I have a 2002 Accent 1.6L and when I turn the wheels all the way too the right or all the way to the left the pulley stops spinning. Could this be that the pump is going bad or something else?
View 2 Replies
My '02 Hyundai accent's power steering pulley makes noise when the car is turned on all the way. That noise doesn't go away until I shut off the car. It is not the same noise as a belt slipping as I have that problem before and had fixed it by tightening the alternator adjuster bolt.
When I spray a little bit of WD-40 on the P/S pulley bolt(bolt and split washer) the noise goes away. However, it comes back the next day, since I am guessing the WD-40 has been dried away. So, should I replace the pulley to fix this issue or is it something else?
Pic of Bolt (Its yellow and black in the pic) ....
View 11 Replies
I am driving an accent crdi 2006. Facing some problem with power steering oil leakage.
View 1 Replies
I have that annoying squeal when I start my car and when I turn my steering wheel (also noticed I can't turn the wheel very well as it feels dodgy, as in the belt catches then lets go if that makes sense). Now once the car warms up it usually doesn't happen again but obviously I want to rectify this as my car draws enough attention at start up but this is getting ridiculous. I checked my power steering fluid and it's bad, brown and has some sediment so it needs changing for sure but here's my problem;
How do I check things to make sure I don't get ripped off at the mechanic? I'm sure a power steering flush and re-tightening of the belt will probably fix it as I've only but 40K on the belts since ikilledbarbie and I changed all of them out. Whay I don't want to have happen is go in and hear "oh you need to replace XYZ" when the problem really is only ABC if you catch my drift.
View 6 Replies
I need to remove the power steering pulley on a 2001 Toyota Celica GTS to replace the pulley shaft's seal. I've got several pullers, so I figure one of them will work. But, I'm concerned that when I pull it out it could damage whatever it messes with inside. Also, I'm going to try doing this with pump on the vehicle.
View 1 Replies
I have a 2009 Accent GLS. The PS pump has become increasingly noisy, especially when the car is first started and when the steering wheel is turned. The noise is coming from the belt and when it does this it looks like the PS pump slows down and the belt is being forced through by the water pump. I bought a new/remanuf pump; however, the PS pressure switch thread diameter is smaller than the hole in the new pump and does not fit.
I took it back and tried another pump and same problem. Looking at a pump on RockAuto, A-1 CARDONE 215473 {#571001E000, 571001G000}, this one shows a plug with a slot in the hole where the switch screws in. I am at a loss with replacing the pump when I cannot seem to find what the car came with.
View 3 Replies
My Santa Fe has a broken power steering pump pulley. Darn thing broke right around the spindle! I can not find a replacement anywhere. I've tried to find a one new, used and at the upull lots (only one Santa Fe in at Pick n Pull dang thing was stripped clean!). The pump is easy to find but this pulley is a ghost!
View 3 Replies
I have accent model 2008, the car has EPS (electrical power steering), Two-days ago, i was driving on high way, suddenly the EPS lit is on and the steering is jammed and i cannot turn it left or right.
I succeeded to stop and turn off then on again, the steering came back to the normal status, I called the service center who i am dealing with him, the Engineer advised me either
1)to change the EPS kit or
2)to change into hydraulic system, i.e., installing a new hydraulic system instead of the electrical one.
View 1 Replies
A friend of mine has a 2007 Accent with some scary MDPS issues. Basically it randomly freezes the steering wheel without a warning making it extremely hard to drive. He went to the dealership and since the car is without warranty they'll charge him 1200$ for repair. Is there any recall on these models for this MDPS?
View 7 Replies
I have a kind of weird problem with my '08 Accent Hatch that just started up last week.
Sometimes when I leave the car (Keys out of ignition and open door) all the doors lock automatically. Same thing happens even if I leave the car running and step out for a minute. And once or twice, the doors locked while driving.
View 11 Replies
Awful belt noise that erupts during cold starts. I realize that this usually means a replaced belt. I want to know how to go along diagnosing which belt and then how to replace it. Here's the symptoms:
1. Awful belt screech when turned on, goes away within 20 seconds
2. Belt noise comes back when turning the wheel to back out of a right driveway
3. The STEERING WHEEL feels like it has no power steering WHILE the screeching is happening.
4. The headlights (when on) dim for about 3 seconds
5. All these symptoms happen when the temperature is below freezing and it's a cold start.
How is the belt screeching connected to the steering wheel being tough I turn?
View 8 Replies
I have a '94 Ford E150 (6 cyl). A few weeks ago the pwr steering fluid began to leak. I couldn't readily see where it was coming from and thought no big deal I'll wait until it's more pronounced. After a week or so of topping off the fluid, I heard a pop under the hood as the serp. belt broke (sheared off actually). Not sure if it matters but at the time I was all manual power with the steering as all the fluid had leaked out.
That's when I noticed that the power steering pulley was slightly out of alignment with the others. I replaced the belt, limped home and the next day the new belt sheared off like the 1st (in ribbons wrapped around the fan). Never had this happen before but is there any way to adjust positioning of the power steering pump and pulley?Looking on the bright side, I'll definitely have a chance to get to that leak now.
View 2 Replies
2010, 5.4L... Noticed a small oil spot under the truck this morning. Took it into the shop after work, we lifted it up, and ran it for 15 min to see where the leak was coming from, and the truck did not leak a drop... until we turned it off. The oil would slowly leak near the power steering pump pulley. But only when the engine was not running ...
View 1 Replies
This problem has plagued me for a while(since last year). When I start the car in the morning, there's a brief period when the power steering is totally gone. When the car is thoroughly warmed up(after 2 minutes of driving), the power steering is back and there will be no problem. Wondering what could that be. The power steering fluid level is normal.
View 5 Replies
One of my belts squeaks. I've tightened one of them as far as it goes I think. The other one is the one with the alternator. Do I tighten the pulley bolt on the alternator to add tension to that one?
View 4 Replies
I purchased a new 2000 mazda b4000 2 weeks ago and the belt was squeaking and I knew I had to change the water pump so I replaced it and the squeaking didn't went away... I thought maybe my idler pulley bearing was worn out cause I could see it wobble back and fourth when the engine was running... Replaced it, still squeaking! Change my belt still squeaking! look further turns out my power steering pulley wobbles slightly. I'm thinking about trying a gator back belt and see if the squeaking goes away. Could it be dangerous to run the truck as it with a slight misalignment in the power steering pulley? or it'll be a must replacement asap?
View 3 Replies
I have a 2011 Corolla LE, about 58k miles. The latest work I did was replace the brake pads, rotate the tires and changed the oil a little over 2 weeks ago. Everything was normal so far. Yesterday I drove for about an hour, again everything was fine, but after stopping at a gas station and starting I have several indicator lights come on.
- Slip indicator, flashing
- TRAC OFF, constant
- ABS, flashing
- Electric power steering warning light, flashes but turns off after about 30 seconds.
I tried my OBD scanner with no luck, but figures since there was no Check Engine light.
View 1 Replies
I recently purchased a used GS350 AWD.After purchasing it, I replaced all of the wheel bearing hub assemblies. The rear ones were grinding, and I decided to just do all 4 at the same time.
After swapping the hub assemblies, the slip indicator light comes on when I go 55+ mph. It's usually when I push on the accelerator. It's not always on. It goes on, then turns off for a while. Sometimes when accelerating it doesn't come on at all. When the light turns on, I loose power for a few seconds but I don't hear or feel any braking.
I have tried an alignment, reset the YAW sensor, etc. The mechanic had a very expensive snap on diagnostic computer and he said everything seems to check out. The steering angle is good, acceleration looks good.
I'm thinking that either one of the hub assemblies has a slight defect that affects the ABS sensors, my VSC computer needs replacing, or YAW sensor starting to go bad.
View 3 Replies
07 f250 I just replaced the power steering pump. I put the serpentine belt back on and when I started my truck I now have a squeaking noise. It's driving me nuts and the more I push the pedal it gets alil louder. Now before I did the ps pump I did hear a little noise like of bearings squeaking when I put my ear to grill.... I put the old ps pump pulley on the new pump but I don't think that is it because it is pressed on. Would it be a bad idler/tension pully? Is it just a coincidence after I do ps pump that it now decides to squeak?
View 10 Replies
