Accent MC (2006-11) :: MIL Flashing And Car Starts To Misfire Significantly
Jun 25, 2015
Started with trouble starting right after a fill up. Right before I was to replace the evap purge valve, I filled up and on my way home, the MIL starts flashing and the car starts to misfire significantly. I replaced the purge valve, but no change in performance (though my car now started up right away after filling it up!). I would drive the car and it would misfire while idling at a light, backing up out of my driveway, accelerating on flat and inclined roads, etc. Codes were 300, 301, 303, and 337 (misfire, misfire, misfire, crankshaft position sensor low voltage)
So, I replace the crankshaft sensor with OEM (this is my 3rd one and this sensor going bad has caused different symptoms each time. First my car would cut out and die while turning, second it would not allow the car to start, and now presumably rough idle). Now the car starts up with less cranking, but still runs rough and misfires (only 301 this time).
So, next I replace the plugs with NGK V's gapped at .044. Better, but not perfect. I noted that the plug in cylinder 1 was darker than the rest.
I read on thread here about regapping to .035, so I tried that. Again, I noted that cylinder 1 plug is slightly darker, while 2-4 have a slight white coating. After the regap, runs great, no misfires, smooth acceleration, perfect...for 24 hours.
On day 2 I start to feel a slight misfire going up a hill, and sometimes at a red light or accelerating from a stop...but not all the time.
Now its day 3 and similar to day 2. Not since I regapped the plugs has the MIL been on, so the misfires are hard enough to feel, but not enough to trigger the MIL.
Not sure where to go next. The coil packs were replaced last year (35,000 miles ago). The car has 137,000 miles on it.
View 7 Replies
Advertisement
I have a 2008 Hyundai Accent that is giving me one heck of a headache. I keep getting a code for number 1 cylinder misfire. When you start it up it runs fine for a while then the CEL will flash and it will start running rough. As soon as I shut it off and restart it, it runs fine. I even experimented with it this morning on the way to work. It started running rough doing 60, I put it in neutral, turned the car off and then right back on, put it back in gear. It ran fine the rest of the way to work. I have swapped coil packs, fuel injectors, spark plugs, and have even hang tested another ECM. Still number 1 cylinder misfire.
View 8 Replies
I did not get the specific cel code but its what the guy told me at autozone.
Long story short. Washed engine, let sit for about 30 mins. Car started with flashing CEL and was "puttering" and very rough idle. Drove home took intake off and replace with stock, took spark plugs out and they were not wet. Then let it sit for about 15 mins. Started just fine. No CEL at all.
The accent saved the CEL and the guy told me that Cylinder 1 had a misfire.
My question is, should I do anything now even though the car seems to be running ok?
View 26 Replies
Ok. Im going to keep this as short as possible. I bought my 05 passat 1.8t AWM TIP used in 09 with 44k
At around 90k I started getting a Random misfire only at idle. And it would be a different cylinder, not always the same would come back after clearing. The RPMs would be very low like around 840. And i think it should be around 920-960. That seems to be one of the main issues. Everything on the car is stock.
So basically, If my CEL starts flashing, and I clear it, I could drive a million miles with no misfires, but as soon as it starts to idle they come back ( I do have vag-com) and know how to use it for basic functions.
This is what has been done:
July 2011:
Engine rebuild (bad piston rings due to clogged cat converter)
Timing belt Kit (Timing was off 5 degrees!!!)
brand new turbo KO3, and Oil feed line
DV
N75 valve
Fuel Pump
Fuel Filter
Fuel Pressure regulator
MAF sensor
ECU swapped out (old ECU would not go through all steps for Throttle body alignment)
So, after all this and 3 weeks later, I get the car back and it ran great the whole way home. Put it in park waited 5 seconds, and the random misfires came back. So it went back to the shop the next day.
September 2011
These things were done:
Crank Position sensor
Cam position sensor
Compression test ( to make sure he didn't make a mistake while rebuilding motor) Results were Perfect
Leakdown test
Map sensor
Another MAF
2 O2 sensors
Upgraded DV
Fuel injectors
Removed engine wiring harness and OHMed every single wire. Nothing wrong
OEM Coilpacks
3 sets of copper plugs
Throttle body was swapped with 2 others from known working cars.
Trans pan replaced fluid flushed and new trans filter
I have heard this is a fairly common thing on the B5.5 models...
View 5 Replies
I got a 2002 and its giving ma a po301. I know that means a misfire in cylinder 1. I replaced the Coils, Plugs and wires, and now its still there but the check engine light is flashing. What next?????
View 2 Replies
My Azera has developed a misfire. Upon leaving work today it ran rough ass soon as I started it. CEL flashing.. I could feel it skipping as I was driving home. Skip never let up.
When I got home, I hooked up the Scanner to it. DTC P0300 was set. Which I think is random misfire. I checked underhood. Nothing appears amiss. With engine off I clear the code and restart the car, This time it set DTC P0301 cyl. #1. I think.
I do not have all the factory service manuals yet. so I need to know what the firing order is on the 2006 3.8 L VIN F Engine. And where the #1 cyl is located. I am suspecting a bad coil at the #1 Cylinder.
View 16 Replies
Been awhile since I've been able to post but I've got a serious issue with my 2006 Ranger XLT 4L V6. So last night about 2 miles from home my check engine light started flashing like it was a at a rave and my engine wasn't acting right, also had the STRONG odor of raw gas, no other lights from the dash, no fluids leaking, oil was good n nothing in radiator but coolant. Was able to baby it to my current home but all my tools are in storage so had to wait to get my ODB scanner to see what's up. Scan came back as 'cylinder #3 misfire' & 'O2 sensor reading rich'.
Go cylinder #3 spark plug out and it were fouled bad. Got ride to the store and got a whole new set. Got back n got'em changed and fired ut up, idle still rough and check engine started flashing again and white cloud coming from exhaust pipe and STRONG odor of gas. Check and now have 'multiple missfire', 'cylinder #2 misfire' and 'cylinder #3 misfire'.
Shut it down go and double check ALL spark plug wires are connected and TRY to start, get about a turn n a half then starter spin. Try again and the engine won't even turn over. "Great I've seized the engine!" Was able to put a socket on the crankshaft pully and manually turn the engine over "whew didn't seize the engine", did this a couple of times and tried to start, was rough but eventually it fired up, still idling rough and again check engine light flashing, while it was running I pulled one plug wire at a time from the coilpack to see/feel the lighting and there was spark for the 3 I pulled, didn't affect engine idle.
Run codes and 'cylinder #3 misfire', so now that the engine is was warmed up I pulled out my ohm meter and started checking wire resistance. Cylinders #1, #2 were at .012, #3 was .011 and #5 was .009.
I've figured that the raw gas is due to cylinder #3 not burning and just pushing gas into the exhaust. So to the brass tacks, do I invest in a new set of wires? Or could it be the injector being stuck open and just flooding the cylinder? No when I originally pulled the #3 plug fuel did not spill out. Haven't pulled #3 again due to it being May in Arizona and had to take a break. I'm going on the assumption that the engine wouldn't start after a short run do to "hydraulic lock in cylinder #3", my manually turning the engine over cleared this and allowed the engine to start.
View 9 Replies
I have a 2006 GX 470, the immobilizer light is flashing but car starts and drives with no problem. How to turn off or reset this light?
View 2 Replies
I know it is a random cylinder misfire code however I started my car in the morning and it was fine I moved it and put it back in my driveway. I started it up later and waited for it to heat up i came back outside 10 min later and my check engine light was flashing and my car was shaking like crazy you could tell the engine was misfiring like crazy. I had under a quarter of a tank but not empty yet. I shut it off and turned it back on and it was still doing it. I drove the mile to the gas station the way it was.
Under partial throttle it was revving to 4500 and over 5, had to let of throttle to make the car shift up a gear. I filled up and started the car again performed fine after that however the check engine light was solid now and still on. I went to my local mechanic and he read that code P0300. I changed my spark plugs that day and they were crap the original spark plugs I have 65,xxx on my car now. Car is smooth now. I cleared check engine when i saw him first and it did not come back on all day even before i changed the spark plugs later that night. Why my light was flashing and why my car was acting like that till i filled up?
View 6 Replies
What is the easiest fix on this and what is the worse case scenario?
View 6 Replies
Yesterday while driving my wifes check engine light came on and started flashing so she limped the car home so that i could take a look at it. I know from previous issues it was a sever cylinder misfire. I hooked up a computer to it and got codes for cylinder 1 &2 having misfires. So today i went and bought new plugs and 2 new ignition coil packs. when i took out the coil pack on cylinder 1 it was broken off and the top of the plug was broken. (nothing entered the cylinder and there wasn't any noticeable oil. But when i changed cylinder2's plug it was covered in oil... i changed the plug and coil pack and cleared the codes from the computer and started it. there was some blue smoke coming out the back (lots actually) for a min or 2 then went to regular exhaust. what would cause the oil in cylinder 2 and possibly 1?
View 4 Replies
I am currently having an issue with my 07 Accent misfiring on cylinder 1. So far, I have changed the spark plugs, which were due anyway, and checked the coil pack. Every coil on each cylinder reads 0.8 ohms, so I am going on the assumption that they are ok. Didn't see any issue with the connector end inside the boot. However, when I changed the plugs, I discovered that I had oil in the plug tubes on 1 and 4. So I changed the valve cover gasket and tube rings and cleaned all oil residue from the packs. I have also checked the short coil wire harness right on the packs themselves. Have not tried to check further because I don't know which pins that harness goes to on which ECM connector. I still have the misfire, and I'm not sure where to go next. I was thinking compression or fuel injector. I don't have a compression tester, and I assume the only way I can check the injector is to swap it with another cylinder?
View 10 Replies
My car has been really acting up lately (AGAIN) so I took it in to have it looked at and they came back and told me it had multiple cylinder misfire, and they wanted like $1200 to fix it. What in the world does that mean and what is entailed in fixing it? They mentioned doing a full maintenance on it.
View 9 Replies
2007 accent randomly starts missing. throws cyl.3 missfire. replaced all plugs and cyl.3 coilpak.
View 2 Replies
i have a 2010 hyundai accent base model with 84,000 miles, recently i fixed my misfire/P030X codes. worked fine for about a couple days then CEL P0420 code came on and performance dropped dramatically. Replaced both o2 sensors and erased codes, drove for about 50-60 miles no CEL but still bad performance. cant get over 60 MPH and sometimes drops down to maxing at 50 MPH. Looked down exhaust manifold with O2 sensor out and saw an intact honeycomb for the cat. What to try next.
View 7 Replies
I have a 2009 Accent. It has a misfire on cyl 3. I've changed the spark plugs... no change. I swapped around the coils... no change. The misfire stays on cyl 3. What are my next steps to isolate and resolve this misfire?
View 10 Replies
As the title says, my CEL goes on and flashes too.
I've read up a bit on why the CEL comes on/flash and it says it has something to do with the exhaust system and if continue operating will damage the catalyst converter (which I don't understand since I'm a car dummy.
In addition, the engine vibrates like crazy. I can feel the engine vibrating when I'm inside the car as well.
I already got the car tolled to the dealership and they kinda just told me it might be misfirings and then they said they couldn't locate the problem. So my car basically has to stay there until they open again on Monday and hopefully they will figure out the problem/fix it under the warranty and call me back.
The problem arise late Friday night and I just did a 30K maintenance on Thursday. (but the car already has 43,000 miles on it).
View 35 Replies
So I've been living in FL and the other day there was a hurricane and the roads flooded. I think I got some water in my engine or somewhere because now my CEL is coming on then flashing and the car sounds like it's underwater! I haven't been able to drive it anywhere to get the code checked, I don't want to drive it because it seems like it's in rough shape. I checked all the plugs and cleaned them, but the 1st one was wet so I think there may have been water in there. After I cleaned the plugs I reset the ECU and the CEL was gone and I drove it 2 miles w/o issue. Then I went to the automotive store to get some oil/filter, etc to change the oil. I get back to my car and as soon as I turn it on again the CEL comes on and then starts flashing after a few mins of me revving it. I noticed that there is water coming out of the exhaust, like a lot more than normal, so what is happening. I did the oil change with no problems but when I started it again the CEL came on and started flashing. 2007 Accent SE
View 3 Replies
I bought a 2009 Hyundai Accent used at 110.000Km. I've only been driving it for 3 weeks and today I went to start the car and it turned over and died right away. It did this a couple of times then it finally started fine and I was able to drive it. What it could be?
View 4 Replies
My 2011 Accent's engine light came on recently. The mechanic said it was a cylinder 3 misfire and recommend changing the spark plug and coil pack for that cylinder. We did that over the weekend. Now the light is back on and has read 5 codes in the past 12 hours (4 at one time). They are P0303, P0304, P0003, P0403, and P0100. I have looked the codes up and can't discern if any could be caused by one main issue. About a month ago it read a code for the oxy sensor, but it went away and never came back.
View 3 Replies
I have a 2010 accent 2.0 with 110k. When accelerating from a stop it seems to hesitate or miss in the first 20 ft or so. The service engine light has not come on which indicates to me it's not in the emission sensors. Where to start looking?
View 10 Replies
