Accent MC (2006-11) :: Headlights Operates In Low But Not High Beam
Oct 31, 2016
08 accent passenger headlight was noticed to not be operating while in low beam. Switched to high beam- it works, but still no low beam.
First instinct was replace the bulb. Low beam works but now.. high beam doesn't?? Bulbs are fine, brand new out of the box and driver's side works like a charm. Bright as heck... passenger's side isn't quite as bright If that's any relation to the problem.
Checked the fuses, they're all good. Made sure bulb was placed in secure. Filament didn't get bounced around either. Was poking around online and seems it could be the relay. Manual doesn't seem to list a relay for the headlights or am I not reading it right?
View 3 Replies
Advertisement
Last week I smelled something burning when I arrived home. I looked around the car and did not see any smoke. I noticed the other night that I had no headlights (low or hi beam) The fog light work fine. No fuses are out.
View 2 Replies
My car is fully stock, with all options available to me (cold weather package not available here). The low-beam triple-LED headlights are aimed way too low compared to all my previous cars, and where they should be. BUT high-beam is aimed properly. So if I adjust the low-beams up, my high-beams might end up lighting up the trees, not the road.
If adjust the headlights up on a fully stock car (not lowered at the front)? Are the high beams still lighting up the road fine? And if you can be specific as the number of turns on the screwdriver, it'd be good too to have an initial adjustment reference.
View 3 Replies
I installed a set of bi-Xenon HIDS identical to these.
in my wife's 2008 Accent. I unplugged the DRL module as shown in a thread I found here, but now there's no high beam indicator on the dash. Is there a wire on the plug that I can put a jumper on or something to make this work again?
And before all the nay-sayers growl at me, instead of assisting with this problem, I aimed the lights really low so there's minimal glare to oncoming traffic. We drove about 125 km last night with them and never got high-beamed once.
View 3 Replies
I bought a 2009 Accent last week after my 1987 Camry wagon bit the dust. It has 47000 km and seems to have been very well maintained. The only problem I have noticed is that the high beam indicator light does not come on, although the hi beams do work. I downloaded an owner's manual but am not sure which fuse the indicator light is on; in any case, everything else seems to be working so I expect the bulb is burned out. My problem : I don't know its location on the instrument panel since it has never worked, and I don't know if it is possible to replace it without special tools.
View 2 Replies
I have a 2012 Hyundai Accent GLS and recently noticed that my low beam only works in the high beam setting and the high beam doesn't work.
View 10 Replies
I own a 2001 Accent 1.6L. The other day both low beam headlights went out. The brights work and so do the parking lights when turned on. I changed the bulbs and still the low beams don't work but the highs and parking lamps do. I looked on the hood for a relay but could find one in the fuse box. I checked the fuses and they appear okay. What could cause the problem? I'm hoping it is not the stalk. Still a relay or switch under the dash?
View 7 Replies
Just discovered that both high beams are not working. Regular lights ok. When switch to high beam both go off. I know some bulbs have two filaments, is this the case for this car? Are the bulbs burnt out or something else is wrong?
This is a 2007 Jeep Wrangler Rubicon Unlimited.
View 11 Replies
I added plow lights to my truck and something quit when I had the high beams all on at once. All 4 shut off. Low beams still working. What I fried or where to check? Its a 99 F250 superduty.
View 14 Replies
When my gas light comes on during the day my horn blows every couple minutes at night time the headlights go from high-beam to low-beam every couple minutes. Also, my check engine light is on more than it is off
View 4 Replies
So I recently bought a 1997 7.3l F250. It is in fairly good condition, but it has some problems with the lights working. The turn signals and hazards all work, as do the tail lights and headlights. However, when I hit the high beam switch, the headlights cut off entirely. Also, the brake lights do not work at all. Ive checked the bulbs and since they all work Im not sure what the issue is.
View 3 Replies
I have a 1995 ranger four letre 5sp, dubbed Beula. I figured there'd be a few gremlins and there was and is, which I know to be more common than not in older trucks. The top priority is figuring out why when I push the lever for the high beams forward, the headlights cut out completely, whether in gear or not, and I don't know where to begin troubleshooting. I've surfed around the forums looking for answers and really only found conjecture.
View 14 Replies
The low beams on my 2010 Sonata seem dim compared to my other vehicles. I do not want to install HID lamps but would like a recommendation for a brighter lamp.
View 8 Replies
How do you adjust the low beam headlights for a 06 Passat? I have found the vertical adjustment now I'm trying to find the horizontal adjustment. For some reason the lights are aimed way out to either the left or the right. Has been like this since I bought the car. Had the car a month, only 42,000 and it's already been in the shop 3 times. Everything from ignition coil, to steering column and comfort control module.
View 5 Replies
I have a 2013 Accent and have installing driving lights. I am looking for the correct high beam wire on the driver's side on the headlight assembly. I will then run this to a relay so that when I turn on my highs, the driving lights will come on. I have tried to locate the correct wire but the one wire that is hot when the highs are on, is still hot when the car is off as well as the lights.
View 6 Replies
I have a 2006 Buick LaCrosse. The low beam headlights have stopped working. I thought that maybe the bulbs needed changed (since I usually have to change them every 6 months) but after changing one with a brand new bulb, it still doesn't work. The "old" bulb looks ok. The fuses are also good (I checked them with a multimeter.) The only thing that I see in my shop manual is something about the ambient light sensor. If this has gone bad, would that cause the low beams to not work? The high beams work fine. The low beams will not work with the headlight switch in the "auto" or "on" position. I don't see any DRL relay or fuse in this car.
View 17 Replies
I have an accent 2006 GS Sedan. I bought this as used recently. Noticed that the lights are not powerful at nights. When I turn on the lights there is no changes in the power of the driving / low beam lights.
Whether this is the standard with accent 2006. Other vehicles I have with me changes the power of the light and in this case there is no changes at all. I bought extra powerful bulbs and put them and there was a slight change, but there is no change between the driving lights and the low beam.
View 4 Replies
Wanted to change my stock yellow high beam (DRL) bulb to an LED bulb i bought from jdmtoys I also changed the parking light to LED and it works perfectly, so after changing the high beam bulbs it worked for few seconds then stopped working... I put back the stock high beam bulbs and it still is not working did i blow a fuse or something? Now when I turn the high beam on my headlight turns on instead of the high beam....
This is the bulb i purchased : [URL] .....
View 14 Replies
My roommate has a 2006 S60 Volvo. One day the passenger turn signal just stopped working. It only works if the high beam is on. The driver side turn signal works fine and so do the emergency flashers. It's not the bulb, not the fuse, not the turn signal lever, and she even took it in the shop and they couldn't figure out the problem without replacing the DIM which would cost a lot.
View 1 Replies
This morning a dash light informed me a headlight bulb was out. It was my DTR light on the passenger side.
I purchased Sylvania H7 high intensity, installed it and it failed to work properly. Daytime light on only drivers side works.
High Beam on , both lights works.
I checked my manual and it said to check fuse in the 5 slot on the driver side dash/door panel and there actually is no fuse in there. I checked the driver side and there was no fuse there either.
I replaced my driver side bulb last year and it took 5 mins....i am already 4 hours into this!
View 4 Replies
I drive a 96 Subaru Legacy. What does it mean when one of the high beams is dimmer (less light output) than the low beam? I am using a brand-new bulb. It's not an adjustment issue because I was looking at the bulb when it was outside of the housing and it clearly gets dimmer when you switch to brights. However, they are equally bright when on low-beam, so I don't think its just a crossed wire.
View 2 Replies
