Accent MC (2006-11) :: Getting P0012 Code
Mar 1, 2016
I am getting a poo12 code on my 2007 hyundai accent. All the sensors seem to be fine. How to get it fixed?
View 9 Replies
Mar 1, 2016
Advertisement
Camry :: 2.4L 2005 Vehicle - P0012 DTC Code
I have been looking for a reason for the P0012 DTC code and was looking for the VVTi Oil control valve & filter. I cannot see where it is on the engine.
View 3 RepliesLexus ES 2007-12 :: CEL On Along With Check VSC - Code P0012
I have a ES 350 and my check engine light is on along with the check VSC and the slippery when wet side. I took it to Toyota and they stated cam timing oil control vaule P0012. Question how serious is this? How long can I drive before anymore problems? It has 107k miles...
View 2 RepliesLexus LS 2007+ :: Check Engine Light Came On - Code P0012
I have an '09 LS SWB AWD with 86k miles on it. A few days ago the check engine light came on with a message on the dash for me to check the VSC system. The next day the check engine light and VSC warning went away on their own. A day after that they came back on. I pulled the ODB codes and got the following:
P0012 - "A" Camshaft Position - Timing Over-Retarded Bank 1
I took it to my local Lexus dealership and they determined that my VVT-i motor assembly needed replacing. Total cost would be $1,222. Apparently this part regulate the camshaft for variable valve timing. I asked if I should notice a performance dropoff since it's related to valve timing but they said no. They said I wouldn't make it worse by driving it so I took my car back and they would order the part for me.
The next day the check engine light and VSC warning went away on their own again and have not come back on for 3 days now. I don't understand why the warning and check engine lights keep going off on their own if this motor assembly needs replacing. Once again it has been 3 days now and no lights have come on.
Ford F-150 (2004-2008) :: Code P0012 - Cam Timing Is Over Retarded
I have a 2004 F-150 FX4 and I am getting Code P0012 on an OBD II code reader. This is saying that the cam timing is over retarded. What is the best way to fix this?
View 5 RepliesFord F-150 (2004-2008) :: 2005 - Rough Idle - Code P0012
I have a 2005 f150 5.4 3 valve with the p0012 code the truck runs good has a rough idle not sure if it is worth changing the vct or not the truck has 190000 miles....
View 1 RepliesFord Super Duty (1999-2016) :: Bad Valvetrain Noise On Power Steering / P0012 Code
I'm working on an 05 with a 5.4. I got it with a bad valvetrain noise on the PS, which ended up being a bad cam, and one bad rocker. I changed the bad rocker and any others that showed any wear, the cam, and all 12 lifters on that head.
The truck starts, idles, runs, and drives fine; identical to my own 05. But if I get on it, it has a dead spot around 3-4k rpm, then picks right up again. After a while, I get the p0012 (Variable camshaft timing over-retarded bank 1). After I get it pissed off, the idle gets rough as well and bogs down.
Now I know the cam went it correctly. I used the wedge tool so the phaser never left the timing chain. I marked the chain as well just to be safe, and the phaser only goes on the cam in one position. Also, it idles too nicely, and runs fine under normal acceleration.
Tonight I swapped the VCT solenoids from one side to the other. It took a lot longer to get the code, but finally came up as a freeze frame dtc, and on Bank 1 again, so it's not the solenoid.
So in my mind, all I can think is that the timing chain jumped (which I don't think is likely due to the good running under normal conditions), or the phaser is bad/sticking on Bank 1. I popped off the oil fill tube and the phaser looks fine physically, so I don't think I banged into it somewhere along the line. I also manually excited the Bank 1 solenoid by grounding the purple wire, and it gives my the same rough idle which I get after the p0012.
It looks like the phaser to me. Another mistake I made was not scanning the truck when I first got it. It came right from a repair shop which diagnosed the camshaft, but I would have at least known if they cleared any codes from it.
Ford F-150 (2004-2008) :: Truck Lost All Power / Barely Staying Running - Code P0012
2008 F150 5.4L .. The truck lost all power the other day driving and barely made it to work. On the ride home it was still running horribly, like it just fell on its face. the check engine light came on. Went to autozone and put HEAT in the gas tank cuz the night before it was at quarter tank and temp went from warm to freezing(thought maybe condensation in tank).. Truck ran a lot better( not perfect). Drove around that day and it was fine. Pulled down the driveway and CE light shut off. Ran the code anyways and it was P0012..
Talked to a few mechanics and they said try replacing the Camshaft position sensors..did so and it ran worse. the truck hardly would idle or rev and shook violently..i shut it down right away. Then it threw 9 codes..Cam shaft position- over retarded timing bank 1(P0012), misfire cyl2, misfire cyl3, misfire cyl 4, random misfire, cam sensor bank 1, three of them were repeated codes..
I replaced the sensors back to stock and cleared the codes. the truck is running like it was in the beginning of the problem..No vilant shaking but falling right on its face at idle and any rpm..not drivable. Would rather do the work myself. very capable except for replacing camshaft phasers which i have heard could be the issue..Could it by the VCT seliniod, EGR valve, plugs, wires...Did just change the oil a week ago and cleaned and reoiled air filter.
Accent MC (2006-11) :: Code P0497 Came On
I have a 2007 hyundai accent 1.6 l gls, recently got a code p0496 and installed a purge valve and 4 days later got a code p0497 (evap emission sys. Low purge flow). Would it be better for me to take my car to an emission shop where it can be diagnosed since i do not want to take to dealership cause the cost would be very high. I want to diagnose it with some machine that will pinpoint the main problem without me replacing parts just to find out that maybe the part i thought was bad did not need to be replaced.
View 2 RepliesAccent MC (2006-11) :: Misfiring On Idle - No Code
Recently got broadsided (passenger), got the body fixed up. Now it is Misfiring on idle and only on idle...
Prior to this I had Coil go out on me, got that changed out, changed the spark plugs. It was running great then the accident happened an this Misfire on idle problem.
Took it to the shop, had them check for a code, no code. They suggested that it made be do to carbon buildup from the previous misfiring issue and suggested using STP engine treatment on it.
Accent MC (2006-11) :: Gas Mileage Went Up - Code P2096
This is in regards to a 2007 Accent 111k miles, about 3 weeks or so .. I had a p0420 code, and replaced the downstream o2 sensor, and the CEL went off, and gas mileage went up. Now today I got p2096 code. Seems to mirror the p0420 code. So now I am thinking the catalytic converter.
So my questions are:
There are two catalytic converters right? one would be the exhaust manifold and the other would be half way through the exhaust system after the two o2 sensors?
Which should be replaced in regards to p2096?
Could anything else be causing this code?
Accent MC (2006-11) :: Check Engine Light Has Been On - Code VSS
My check engine light has been on for months and the only code coming up is for the VSS. I got the VSS replaced and the light came back on as soon as I hit 70 on the freeway. Checked the code again and the same one came up. Is this a common issue with 06 Accents? I'm wondering if it might be a wiring or computer issue... My ABS light is also on, would this have anything to do with it?
View 5 RepliesAccent MC (2006-11) :: Misfire With Error Code P0302
2009 Accent, 1.6L 154,xxx Cylinder two misfire. Engine was rebuilt due to timing belt. Twice. Second time I did it. Replaced plugs, coil packs, all gaskets, (everything new in the head) did a smoke test, compression test 180 psi across all four, used a noid light for coil packs (good) did it at the injectors 1,3,4 did good, but 2 came on then went off. Check resistance and it shows good, replaced injector anyway and the connecter. Still doesn't work. Checked powers and grounds at the rail, good. Good solid voltage. I hooked up a scan tool and tried to shut injector 2 off, no change in RPM or vibration. Scan tool worked for 1,3,4. Used another PCM, still misfire in two. Even jumped a wire from PCM control and 15A inj fuse for the 12V constant (bypassed the harness) and still doesn't work. Also have knock sensor code, just two codes.
View 14 RepliesAccent MC (2006-11) :: VSS Code PO501 - No Faults Found
Have VSS code PO501. Have fitted new right vehicle side speed sensor, after reset code clears but quickly returns so still got code. Speedo is working. Have sent ECU for testing - no faults found.
Car is an auto, can the left/drivers side sensor cause this or the transmission sensor cause this?
Accent MC (2006-11) :: Code P0339 - Car Stalling While Idling
Twice today my car stalled out while idling. Once at a left turn red light and once in the drive thru. The first time it restarted after about 10 minutes. The second time it restarted after about 2 minutes.
Car is throwing cod P0339 for Crankshaft Position Sensor A Circuit Intermittent.
I did some reading up on this on the forums but didn't do much about it. I just tried wiggling the wiring and all that when idling, didn't notice any roughness or stalling so.... may not be a connector issue.
Anyhow, planning to take it in for diagnosis and repair as it's really not derivable the way it is.
Actually this is the first time ever the car has given me engine trouble of any kind. just passed 90,000 miles. Shucks, streak broken.
Accent MC (2006-11) :: 2010 GL - Misfire On Cylinder 2 / Code P0302
I have a 2010 accent GL manual sedan. It has 104,962 KM on it, the warranty expired December 18, 2015. Since February this car has become a frustrating money pit. Being in the dealership constantly for repairs, then within a week something else 'happens' and back it goes. Spent almost $5000 in 4 months on repairs. Decided that's enough and will do majority of repairs myself.
Yesterday while drive on the highway I had a sudden loss of power and a check engine light came on. My scanner which has become a standard item in my glove box indicated a misfire on cylinder 2 - P0302. I limped the car home, in 3rd gear I was having a hard time staying above 2000rpm at 60km/h. at lights I had to use hand brake so I could keep my foot on accelerator, revs were dropping below 300.
Today I replaced all the plugs (all 4 were still in good or better condition, #2 showed signs of a slightly rich burn and #3 a slightly lean burn), replaced all coil boots (no cracks, no burns, and still pliable), removed and cleaned all the injectors. Error code P0302 persists.
Accent MC (2006-11) :: 2008 - Code For Cylinder 1 Misfire / CEL Flashing
I have a 2008 Hyundai Accent that is giving me one heck of a headache. I keep getting a code for number 1 cylinder misfire. When you start it up it runs fine for a while then the CEL will flash and it will start running rough. As soon as I shut it off and restart it, it runs fine. I even experimented with it this morning on the way to work. It started running rough doing 60, I put it in neutral, turned the car off and then right back on, put it back in gear. It ran fine the rest of the way to work. I have swapped coil packs, fuel injectors, spark plugs, and have even hang tested another ECM. Still number 1 cylinder misfire.
View 8 RepliesAccent MC (2006-11) :: CEL Code P0420 Bank 1 Popped Up While Driving
P0420 bank 1 code popped up while driving. Im thinking this is just an oxygen sensor? Is it ok to drive with this code for a while if i buy an o2 sensor online?
View 5 RepliesAccent MC (2006-11) :: Shuddering When Vehicle Is Placed In Gear - Code P0301
When looking at the engine from the front of the vehicle. what numbers are the cylinders from left to right? To curtail off of that question where do I locate the corresponding ignition coils to these c I have been dealing with intermittent misfires on cylinders 1 and 3 codes P0300, P0301, P0303. I replaced the spark plugs to no avail. Whenever the vehicle shudders the headlights dim and the shuddering is worse when the vehicle is placed in gear, the A/C fan is on, or the vehicle is accelerating. Once I reach a certain speed, usually 35-40 mph, I don't notice until I again slow down. I replaced the spark plugs the day after I had the first issue appear which read code P0301. Prior to installing the spark plugs, I experienced a severe loss of acceleration power, but now only experience the shuddering.
2011 Hyundai Accent 63500 miles ....
Accent MC (2006-11) :: Got A Check Engine Light Code P0139
I did a spirited sprint from a stop light and then got this cel. It says it's for the second 02 sensor. I got home, jacked it up and checked it out. Everything looked, sounded, smelled, ran fine. What should I do?
View 28 RepliesAccent MC (2006-11) :: CEL Code P0171 - Misfires With Full Throttle
My accent 2006 has the check engine code p0171. AT mornings I have to start the car like 5 times until it revs up and do not stall. Also when the car is running, If I press the gas too much it starts misfiring and have really slow acceleration. I have already change the 02 Sensor, spark plugs, TPS and maf sensor, and PSV valve, cleaner the throttle. I really don't know what else to look for.
View 5 Replies